Products

AUNOV PRODUCT RANGE

Precision Deep Drawn & Stamped Products

Six product families, one factory — every part drawn, machined and inspected under our own roof.

Aunov Tech builds custom metal parts to print across six product families — precision deep drawn parts, drawn tubes and sleeves, sensor housings, custom metal stampings, CNC-machined components and automotive motor parts. We draw stainless steel, aluminum and copper alloys on mechanical and hydraulic press lines, finish them in our own CNC cells, and inspect every batch before packing. Send us your drawing and annual quantity; our engineers will come back with material advice, tooling cost and a per-piece price within 24 hours.

Precision Deep Drawn Parts
The core of our shop — seamless shells, cans and enclosures drawn on 5–500T press lines, in stainless steel, aluminum and copper alloys.
Explore →
Deep Drawn Tubes & Sleeves
Seamless drawn tubes for expansion valves, solenoid valves and oxygen-sensor fittings — no weld line on the wall, bore and OD held to gauge.
Explore →
Sensor Housings
Deep drawn stainless steel housings for automotive and industrial sensors — closed tolerances, size held through the draw, wall thickness you can trust.
Explore →
Custom Metal Stamping Parts
Brackets, shields, covers and formed parts stamped to print on progressive, transfer and single-stage dies — blanking to finished part in one factory.
Explore →
CNC Machining Parts
Turning, milling and trimming cells that take drawn blanks to final print — threads, faces and seal surfaces machined in one pass through the shop.
Explore →
Automotive Motor Components
Drawn and stamped motor housings, frames and yokes for DC motors, fuel pumps and window regulators — balanced for spin, sized for assembly.
Explore →
CUSTOM PARTS
Can’t find your part family here?
Send us your drawing — if it is drawn, stamped or machined from coil, we can likely build it.
Request a quote →

Built In-House, From Coil to Carton

15+
Years of Experience
5–500T
Press Range
500+
Tools Built In-House
30+
Countries Served

Materials, Tolerances and Lead Times

Every part in the catalogue is quoted from your drawing, but three questions decide most programmes: what the part is made of, which dimensions actually matter, and when you need it.

  • Materials. Cold-rolled steel SPCC and DC01–DC06, stainless steel SUS304 and SUS316, aluminium 1050 to 6061, and brass and copper for conductive parts. We advise the grade that draws most easily for the geometry rather than the one with the highest number.
  • Tolerances. Formed diameters and lengths are held consistently once the draw schedule is proven; features tighter than forming allows are machined afterwards. Tolerance only the surfaces that functionally matter — marking everything critical adds operations without adding function.
  • Thickness range. From 0.15 mm foil to 3.0 mm sheet, drawn to depths up to about 150 mm on press lines from 5 to 500 tonnes.
  • Lead time. New tooling typically samples in three to four weeks from purchase order; repeat orders run against the existing tool, so the schedule is set by the press and the finishing route rather than by tooling.

If a requirement sits outside deep drawing, we quote the process that fits instead — stamping, CNC machining or a hybrid route. The engineering behind those decisions is explained in our deep drawing process and material selection pages.

Send Us Your Drawing

STEP, DWG or PDF — our engineers reply with tooling cost and a per-piece price within 24 hours.

Complete product catalogue

Every part below is produced in our own plant – drawn, stamped, finished and inspected in house. Open any part for its drawing route, materials, tolerances and tolerance discipline.

Deep drawn parts (58)

Seamless cans, shells, covers and caps drawn deeper than wide.

Automotive motor components (53)

Motor housings, cans, end caps and brackets for DC motors and actuators.

Sensor housings (17)

Sensor shells, frames, sleeves and housings in stainless steel and brass.

CNC machining parts (6)

Formed blanks finished by CNC – threads, seal faces and precision bores.

Deep drawn tubes & sleeves (4)

Thin-wall drawn tubes and sleeves for valves and fluid control.

Explore Our Product Categories

What Are Deep Drawn Metal Products?

Deep drawn parts are seamless metal components formed by drawing a flat sheet-metal blank into a die rather than by cutting, folding or joining, so the finished shell has no weld line and a wall that stays continuous from base to rim. Tensile forming of sheet is classified under DIN 8584. Alongside drawn parts we build drawn tubes and sleeves, sensor housings, custom metal stampings, CNC-machined components and automotive motor parts, which lets one drawing travel from coil to finished component without leaving our factory.

What is the difference between deep drawn parts and stamped parts?

Deep drawing pulls a flat blank into a die so the metal flows into a seamless shell whose depth is greater than its diameter, while conventional stamping mostly cuts, bends or pierces the sheet without forming that depth. Drawing gives you a leak-tight one-piece body with no seam to fail, and stamping is usually faster and cheaper for flat brackets, shields and clips. We run both, on press lines from 5 to 500 tonnes for drawing and progressive, transfer and single-stage dies for stampings, so we will recommend the route that suits your geometry and annual volume.

Can one part combine drawing, machining and stamping?

Yes. A drawn can often needs a pierced hole, a machined thread, a trimmed flange or a welded boss, and keeping those steps under one roof removes the tolerance stack that appears when separate suppliers each work to their own datum. Most parts continue through CNC trimming, welding and inspection in-house, so one supplier controls the whole chain from material certificate to export carton.

Which metal should I choose for a corrosive environment?

Stainless steel is the usual answer where the part sees moisture, road salt or cleaning chemicals, and it also takes passivation and electropolishing well. Common stainless steel sheet grades are specified in ASTM A240/A240M. Where weight matters more, aluminum is lighter and forms predictably in deep draws; where electrical or thermal conductivity matters, copper and brass are worth considering. We draw stainless steel, aluminum and copper alloys, and we will suggest a grade once we know the operating environment.

Do you supply assemblies, or individual components only?

Both. We ship individual drawn components when you prefer to assemble in your own plant, and we can deliver completed parts where a drawn shell needs trimming, piercing, welding, cleaning and inspection before packing. Tell us which scope you want quoted and we price to that drawing.

What do you need from me to quote a part?

A drawing with the critical dimensions marked, your expected annual quantity, and the material you have in mind. Our engineers come back with material advice, estimated tooling cost and a per-piece price within 24 hours. Minimum order quantities start at 1,000 pieces.