
Precision at the metering point: the electronic expansion valve tube
Electronic expansion valves turn refrigerant flow into a controlled variable – the stepper motor or solenoid positioning a needle in a bore, the controller modulating flow to hold superheat – and the deep drawn electronic expansion valve tube is the precision element at the heart of that control. Where a thermostatic valve tolerated a mechanical envelope, an electronic valve asks the tube to hold a metering bore to a tolerance that directly sets flow resolution. This page covers what that precision demands of the drawing and finishing.
The bore that sets flow resolution
In an electronic expansion valve, the needle and bore form a variable orifice whose area sets flow. Control resolution – how finely the valve can modulate – depends on the bore’s diameter accuracy, roundness and straightness, and on the surface finish the needle slides against. A bore that is 0.02 mm oversize shifts the entire flow curve; an oval bore modulates flow as the needle rotates; a scored bore changes flow with wear. Our approach: draw the tube, then refine the bore by sizing, ironing or burnishing to the metering tolerance, verify diameter and roundness with metrology matched to the valve maker’s gauges, and specify finish by roughness band validated with the customer’s needle. Where the flow curve is sensitive, we recommend a flow test on first articles with the customer’s own needle and seat, because the flow characteristic is a system property and the bore is only one of its inputs.
Straightness and concentricity through the tube
An electronic valve’s needle travels through the bore, and its alignment depends on the tube’s straightness and on the concentricity of the bore to whatever features mount or seal the tube. A tube that bows slightly causes the needle to rub, which increases hysteresis – the difference between the position that opens and the position that closes – and hysteresis is exactly what a closed-loop controller dislikes. Our designs keep the tube’s straightness by controlled draw sequences and, where necessary, a straightening pass, and we tie the bore’s position to the mounting datum so concentricity is a tooling property rather than an assembly one. First-article verification includes a through-gauge straightness check and a concentricity measurement against the mounting features.
Materials and refrigerant compatibility
Electronic expansion valve tubes are commonly austenitic stainless steel – 304 or 316L – for corrosion resistance against refrigerant and lubricant breakdown products, and for the cleanliness that refrigeration demands. Where the valve uses a magnetic actuator element, the material question gains a magnetic dimension, as on our solenoid valve tube page: a ferritic section or insert may serve as a flux path while austenitic material elsewhere resists corrosion. We ask for the actuator architecture at RFQ so the material selection follows function. As ever with austenitics, the draw sequence accounts for work hardening, and where the bore precision requires it, an anneal precedes the finishing passes.
Cleanliness and joining for a sealed circuit
Electronic expansion valve tubes join a refrigerant circuit that is sealed for years, so cleanliness and joint integrity are safety-of-the-system issues. Our finishing includes degreasing, passivation, and residue and particle verification with the record travelling with the lot; packing protects the cleanliness with capped, individually bagged tubes. The joining interfaces – brazed or welded to the valve body and to system tubing – are dimensioned for the process, with the fit band set so filler penetrates a capillary gap without the risk of a cold joint, and validated by a brazing trial on first articles where the customer’s process is known. For a circuit that cannot be serviced easily, these details are the difference between a valve that runs for a decade and one that leaks in year two.
Metering-grade bores are held by sizing and burnishing
The tube drawing with metering bore diameter, roundness, straightness and finish; the needle’s fit dimensions; the actuator architecture (for material and magnetic behaviour); the refrigerant and lubricant; the joining process and mating interfaces; the cleanliness standard; and volume. We return a draw and finishing plan, a material recommendation, and a sample schedule – typically three to five weeks after die approval, with first articles carrying bore metrology, straightness, finish, the cleanliness record and a flow test with the customer’s needle if specified.
How tight a bore can you hold, and at what cost?
How tight a bore can you hold, and at what cost?
Metering-grade bores are held by sizing and burnishing after the draw; the cost is the finishing operation and its metrology, which the quote names. Extremely tight tolerances may need a machined bore instead – we will tell you which route your tolerance requires.
Our valve shows hysteresis – is the tube the cause?
Possibly, if the bore is bowed, oval or rough enough for the needle to rub. Send cycled tubes; bore and straightness metrology will show whether the geometry drifted or the needle wore.
Do you supply tubes with the bore matched to our needle?
Yes – finish and diameter are matched to the needle’s print, and where the application warrants it we run a sliding or flow check with the customer’s needle before shipping first articles.
Deep Drawn Tubes & Sleeves is the parent range for parts like this one; the overview page gathers the tooling logic, finishing options and tolerance notes that apply across the family.
Where this part is used
An electronic expansion valve replaced the thermostatic valve by moving the control decision from a mechanical element to a motor and a controller. The part that made that trade possible is the tube: a drawn sleeve whose bore can be held accurately enough that the controller’s commands produce repeatable flow. The motor can position the needle precisely, but only if the bore it moves in is a known cylinder rather than an approximation, and only if the tube is straight enough that the needle does not rub as it travels.
You will find these tubes in commercial refrigeration and air-conditioning systems, in chillers, in supermarket and cold-chain equipment, and in any modern refrigerant circuit where superheat has to be held within a tight band. As systems get more efficient the control margin narrows, and the metering bore stops being a generic precision tube and becomes a part whose tolerance scheme is set by the valve’s flow curve.
What we need to quote it
Give us the bore diameter and the tolerance on it, the needle or seat geometry it works against, and the refrigerant with its pressure and temperature range. Straightness over the working length matters as much as diameter here, so tell us what the controller expects. If the flow characteristic is sensitive, we would rather run a first-article flow test with your own needle and seat than judge it from a dimensional report alone.
Specifications
| Item | Deep Drawn Electronic Expansion Valve Tube |
|---|---|
| Brand | AUNOV |
| Designing | DFM feedback accompanies the quotation, so surprises are caught before the die is cut. |
| Tooling | Progressive and drawing dies are designed and built in house, so a die can be re-cut against the approved drawing, and maintenance is tracked against the part number. |
| Samples | Sample lead time is quoted with the order, and the approved sample governs the run. |
| Materials | Materials held include carbon steel, 304 / 316 stainless steel, aluminium and brass; mill certificates and heat numbers accompany the first article. |
| Surface finish | Plating, powder coating, anodising or polishing, per the print; finish thickness and adhesion checked on the first article. |
| Processing | Tube drawing with precision turning on critical diameters; first articles verify the whole flow before the run is released. |
| Equipment | Drawn-tube benches, in-line annealing and CNC turning, with in-house toolmaking to keep dies and fixtures maintained. |
| Tolerance | +/-0.03 mm on machined ends, straightness per print; finer bands confirmed from capability data before quoting. |
| Delivery terms | Freight is quoted to your door in FOB, CIF or DDP terms, payment by T/T or L/C. |
Related Products
Request a Quote for This Part
Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).




