
A valve tube’s job: a bore that seals, cycle after cycle
In a valve, the tube is not just a passage – it is the surface a plunger or poppet runs against, the seat that seals, and the body that holds pressure between actuations. A stainless steel deep drawn valve tube is engineered around those three functions, and its drawing has to deliver a bore accurate enough to seal, smooth enough to let the moving element slide, and clean enough not to contaminate the fluid it controls. This page covers valve tubes specifically, where the demands differ from a general pump tube.
The bore as a sealing and sliding surface
A valve tube’s bore often does double duty: it guides a plunger and provides the surface a seal or an O-ring rides on. That combination sets the bore’s requirements – diameter to a sealing tolerance (measured in hundredths of a millimetre), roundness tight enough that the seal compresses uniformly, and a surface finish smooth enough to let the seal slide without tearing but not so polished that it fails to retain a fluid film. Deep drawing forms the bore as the punch leaves it; achieving the sealing-surface quality then means a controlled sequence of sizing, ironing or burnishing passes, chosen per application. We hold bore diameters and roundness by sizing after the draw, specify surface finish by roughness band, and verify both on first articles with the metrology the valve maker’s own gauges use. For an application where the seal is critical, we recommend testing the drawn and finished bore with the customer’s actual seal in a proof cycle, because finish numbers alone do not predict seal life.
Stress and the pressure cycle
Valve tubes cycle pressure – open, closed, open, closed, thousands or millions of times. That cycling, not the static pressure, is what fatigues the tube, and it concentrates where geometry changes: the transition from the bore to a shoulder, the closed end, a thin wall near a port. Our designs for cycling service keep those transitions generous, avoid abrupt features, and where the application demands it, verify fatigue by pressure cycling the drawn tube to a specified count with inspection at intervals. A valve tube that passes a burst test and fails a cycle test has a stress-concentration problem in its geometry, and that is a design decision made before tooling.
Cleanliness is functional, not cosmetic
In valve service, contamination is a failure: a metal particle that lodges in a seal scores the bore and starts a leak, and residual drawing lubricant is a source of such particles. Our valve-tube finishing includes thorough degreasing, passivation, and a cleanliness verification – particle and residue checks – before packaging, with capped ends and individual protection so the tube arrives clean. Documentation travels with the lot, and for regulated applications (medical, pharma, food) the cleaning record is delivered as part of the tube’s file. This is one of the clearest cases where a supplier’s process discipline, not the part’s shape, decides whether the component works.
Materials, and the stainless steel question
Valve tubes are predominantly 316L/1.4404 for its resistance to chlorides and process chemicals, with 304/1.4301 for less aggressive fluids and 1.4016 ferritic where cost matters and corrosion is mild. Austenitics require the draw care described on our pump-tube page – generous radii, possible intermediate anneal – and the quote reflects that instead of hiding it. Where a valve’s design pairs a stainless steel tube with a magnetic element, note that the magnetic behaviour matters: a ferritic grade may be specified for magnetic function while an austenitic is chosen for corrosion, and a supplier who swaps them for cost will change the valve’s performance. We flag the distinction in every review.
Sizing and burnishing, as with any precise bore
The valve tube drawing with bore diameter and tolerance, roundness, surface finish (roughness band), the moving element’s fit, the pressure and cycle spec, the material grade, the cleanliness and documentation level, and volume. We return a draw and finishing plan, a proof or cycle test proposal, and a sample schedule – typically three to five weeks after die approval, with first articles carrying bore metrology, finish and the cleaning record.
Can you hold the bore roundness our seal needs?
Can you hold the bore roundness our seal needs?
Yes, via sizing and burnishing after the draw – as with any precise bore, the tolerance is bought with a finishing operation, and the quote names it. If your tolerance sits at the edge of achievability, we will say so before tooling.
Our valves leak after a few thousand cycles – tube or seal?
Could be either, but a bore that lost roundness or finish will tear seals. Send cycled tubes; our bore metrology separates a worn bore from a worn seal.
Do you supply tubes with the port features formed?
Yes – ports, shoulders and sealing lands are die geometry where the drawing allows, positioned to the same datum as the bore. Complex port geometry may need a subsequent operation, which the quote will show.
This part belongs to our Deep Drawn Tubes & Sleeves range. The deep drawn tubes & sleeves pages collect the process notes, common materials and inspection points behind every product in the family.
Where this part is used
A valve tube is the passage and the seal at the same time. Inside it, a plunger or poppet slides against the bore to shut the flow off, and the same bore carries the pressure that the valve is rated for. That double duty is what separates a valve tube from a general pump or hydraulic tube: the bore has to be accurate enough to seal and smooth enough for the moving element to travel without galling, and the wall has to survive a pressure cycle rather than a static load.
You will find this part in refrigeration and HVAC control valves, in hydraulic and pneumatic sequence valves, in instrumentation manifolds, and in metering equipment where a measured volume of fluid has to pass reliably every time. Where the fluid is clean and the cycling is frequent – refrigerant, medical fluid, analyser gas – the cleanliness and surface-finish requirements become as much a part of the specification as the diameter.
What we need to quote it
Send us the bore diameter with the tolerance the seal needs, the pressure the tube will see and how often it cycles, and the fluid with its temperature range. Roundness and the bore’s surface-finish band are worth stating too, because they decide how the seal behaves. If you already have a valve that performs acceptably, a sample tube with a measurement report is usually the fastest route to a comparable one.
Specifications
| Item | Stainless steel deep drawn valve tube |
|---|---|
| Brand | AUNOV |
| Designing | Driven by your drawing or a physical sample – unusual walls, threads or tolerances are feasibility-checked first; revisions are re-quoted once rather than silently absorbed. |
| Tooling | Our toolroom covers die design, wire-cut EDM and maintenance, so die cost stays transparent, and the die remains dedicated to your part. |
| Samples | Sample and first article are the same discipline here: measured, reported, then approved. |
| Materials | Materials held include carbon steel, 304 / 316 stainless steel, aluminium and brass; grade and temper are confirmed in writing before tooling. |
| Surface finish | The drawing selects the finish: plating, coating, anodising or passivation, with masking and laser marking available where needed. |
| Processing | Tube drawing with precision turning on critical diameters; first articles verify the whole flow before the run is released. |
| Equipment | Drawn-tube benches, in-line annealing and CNC turning; first articles and batch samples are checked on the CMM. |
| Tolerance | +/-0.03 mm on machined ends, straightness per print; GD&T per drawing, PPAP-style reports on request. |
| Delivery terms | Delivery quoted per Incoterms 2020 – FOB, CIF or DDP – by sea or air, to your address. |
Related Products
Request a Quote for This Part
Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).




