Stainless Steel Hex Reducer Bushings – CNC Machined

Specifications

Frequently Asked Questions

Two diameters on one part do two jobs – what keeps their bands apart?

Direct answer: Because they do different jobs. One diameter may locate, the other may carry a seal or a thread, and each has its own tolerance and its own finish. The drawing has to treat them separately rather than giving both the same band, because one band cannot serve two functions.

The hex on a turned part is more than a wrench flat – what else is it?

Direct answer: It stops the part rotating, and it is often a datum. The hex is what the installer grips, but it is also the feature that orients the part, so its position relative to the other features matters. The hex is a functional orientation feature, not just a wrench interface.

Why are the lead-in and the chamfer functional?

Direct answer: Because they are what let the part enter its mate without galling or jamming. A lead-in guides the part into a bore; a chamfer protects a thread’s first turn. Both are functional features that prevent assembly damage, and they are specified rather than left to the shop.

ItemStainless Steel Hex Reducer Bushing CNC Machined
BrandAUNOV
DesigningMade to your 2D/3D drawings (PDF, DWG, STEP, IGS) – samples are reverse-measured into a controlled drawing; the same drawing is used for every repeat order.
ToolingTooling is built and held under your part number, so a die can be re-cut against the approved drawing, and ownership is confirmed on the quotation.
SamplesSamples are issued for approval before the run, so the sample is retained as the master, and later batches are gauged back to the signed sample.
MaterialsStock covers carbon steel (SPCC / DC01), 304 / 316 stainless steel, aluminium and brass; grade and temper are confirmed in writing before tooling.
Surface finishPlating, coating, anodising or passivation are chosen from the drawing; masking and laser marking are available where the job needs them.
ProcessingCNC turning with milling and drilling in as few setups as the geometry allows; first articles verify the whole flow before the run is released.
EquipmentTurning centres fed from bar, with machining centres for milled features, backed by CNC turning centres and a climate-controlled inspection room.
Tolerance+/-0.01 mm on turned and milled features; finer bands confirmed from capability data before quoting.
Delivery termsFOB, CIF or DDP per Incoterms 2020, payment by T/T or L/C, quoted in USD or EUR; sea or air freight is quoted to your door.

A hex reducer bushing is a small, cheap, standard-looking part, and it is one of the most instructive examples of a component whose tolerances are all relationships between two of its own features. A reducer bushing’s job is to go into a hole and come out smaller, and it has to do that while being located by the hole and driven by something external. Every dimension that matters is a fit, and two of them are more important than its size.

The reducer’s defining characteristic is that its two diameters are both functional, and they are functional in different ways – which is the distinction this page is about.

Two diameters, two different requirements

  • The outside diameter is a location. It fits into a hole in the mating part, and that hole is what locates the bushing – concentric to it, angular to it, and axially. So the OD’s requirements are a fit to the mating hole, roundness, and concentricity of everything else to the OD.
  • The inside diameter is a passage or a thread. If it is threaded, it is a thread that a fitting screws into, and its requirements are a thread class, a pitch diameter, and a form. If it is a plain bore, it is a passage and its requirements are the bore’s size, roundness and surface finish, plus a lead-in.

The mistake that this part invites is to specify both diameters to the same tolerance band and call it done. They are different features with different requirements and different failure modes, and the tolerance scheme should reflect that. In practice the OD is usually the one that has to be tighter, because it is the locating feature and because a mis-sized OD cannot be forced, while a slightly loose bore can often be accommodated by the fitting’s own tolerance.

The hex, which does more than take a wrench

The hex on a reducer bushing is usually treated as a feature for a spanner, and it does that job, but on a reducer it carries a second load that is frequently missed: the drive torque.

  1. When is the reducer driven? A reducer bushing is commonly used to bring a small threaded fitting into a larger hole, and it may be screwed into place by its hex rather than held by the fitting. If so, the hex has to transmit the torque of the connection, and the hex’s flats are the shear path. A thin hex will deform and a rounded hex cannot be undone.
  2. The hex is also the assembly’s indexing reference. On a fitting assembly with more than one hexagonal part, the hexes’ angular relationship is sometimes functional – a wrench applied to one and to the other in sequence, or an orientation requirement for a valve handle. Where that applies it should be stated as an angular tolerance, not left to the general tolerance.
  3. Width across flats is a fit, not a size. It is the wrench interface and it has to be within the tolerance for the wrench or the corners round. This is the same requirement as on a hex cap nut, and it deserves the same specification.

The lead-in and the chamfer, which are functional

Two chamfers on this part, and they do different jobs.

  • The bore’s lead-in. On a threaded bore, the entry chamfer on the thread is what allows the fitting to start without damaging the thread’s first turn. A too-small chamfer will make the fitting hard to start and will deform the thread; a too-large chamfer removes engaged turns and reduces the thread’s strength. Both are functional, so the chamfer’s angle and its diameter should be specified.
  • The OD’s chamfer or its relief. On a bushing that is pressed or driven into a hole, a lead-in on the OD is what guides it. And where the bushing is driven to a position, the lead-in’s length and angle determine how much of the driving force becomes insertion and how much becomes a wedging load on the hole’s edge.
  • The edge break on the hex’s corners. Small, functional, and frequently omitted. A sharp corner on a brass or steel hex is a hazard and it is also where a crack would start if the hex were over-stressed.

Material, and the specific choices on this part

Carbon steel, 304 and 316 stainless steel, aluminium and brass, with grade and temper confirmed in writing before tooling. On a reducer bushing the material decision has four considerations and they are all specific to this part rather than general.

  • Corrosion, from the environment the bushing sits in. The OD is in contact with the mating part and often with moisture, and the crevice at the joint is where it will corrode. 304 for general service, 316L for anything chloride-bearing – and the same galvanic question as everywhere else: a stainless steel reducer in an aluminium housing, or a steel reducer in an aluminium housing, is a couple.
  • Hardness, if the bushing is driven. A bushing that will be hammered or driven into place needs to resist deforming at its OD. A soft bushing will ovalise in the hole and then be loose, and once it is loose it will wear and become a leak path. This is a real and common cause of a reducer that stops sealing, and the fix is a harder material or a designed press fit rather than a driven one.
  • Brass is the traditional material for a reducer in a fitting assembly, because it is easy to machine, it seals by deformation, and it is forgiving of the small mismatches that occur in assembly. Its specific limit here is dezincification in a wet environment, and its galling against a steel fitting.
  • Aluminium is used where weight or a thermal path matters, and it is a poor choice for a bushing that will be driven, because it deforms too readily and its thread will strip.

Surface finish, and the masking question

Finish selected from the drawing – plating, coating, anodising or passivation – with masking and laser marking available. Three specific cases on this part.

  • The thread must usually be masked or specified post-finish. A plated thread in the bore changes the fit and it will flake at the thread’s roots. This is the single most important masking requirement on the part.
  • The OD’s plating changes the fit in the mating hole. If the OD is a close fit, plating it closes the fit; if the fit is a slip fit, plating may close it to interference. Either the hole is specified for the finished condition or the OD is masked.
  • An anodised aluminium bushing has a specific and commonly-missed problem: the anodising on a part that goes into a hole and conducts heat is a thermal insulator at exactly the interface where heat has to move. On a bushing used as a thermal interface, the anodic layer is the whole problem.
  • Laser marking is a sensible identification method on a small part like this because it does not add thickness and does not affect any fit – which is not true of a stamped or engraved mark on a small bushing.

Tolerance, allocated to the two fits

+/-0.01 mm on turned and milled features, finer bands confirmed from capability data. On this part the flagged dimensions are the two fits and the relationships between them.

  • The OD, stated as a fit to the mating hole, with roundness and cylindricity as separate requirements. Where the hole is not controlled by the same drawing, this tolerance should be agreed with the part that owns the hole.
  • The thread’s class and pitch diameter, gauged, and stated pre- or post-finish.
  • Concentricity of the bore to the OD, which is what keeps the bushing’s passage aligned with the hole it is in. On a small bushing this is the tolerance that prevents the fitting from sitting off-axis in the hole and it is normally written as a general tolerance.
  • Angular position of the hex relative to the OD and to the bore, where it is functional.
  • Width across flats as a fit to the wrench.
  • Length at a general band, unless it is the dimension that sets the insertion depth.
  • Chamfer angles and diameters, stated, on both chamfers.

Why a reducer is machined rather than made another way

A reducer bushing is one of the parts where the obvious low-cost route is available and is often wrong, and it is worth naming because it changes the tolerance scheme.

  • Stamped from strip. A hex-shaped blank with a round hole punched in it is a simple piercing die and it is the cheapest possible route at volume. The problem is exactly the one covered on the stamping page: the OD’s size and the bore’s position both come from the punch’s alignment, and the OD’s roundness comes from the strip’s thickness and the die’s condition. A reducer that has to locate a fitting will drift, and a drifting reducer will eventually leak at its union.
  • From hex bar or hex tube. A part cut from hex bar with a bore drilled through it is very cheap and it is the traditional route. It has two specific limitations. The bore’s position comes from the drilling, and on hex stock the flats are not concentric with anything in particular, so the bore’s position relative to the hex flats varies with the bar. And the bore’s size is limited by what can be drilled through the bar without drifting.
  • Machined from round bar, with the hex milled. This is the route that gives the accuracy, and it is the right one whenever the reducer’s bore is threaded and has to seal, or its OD has to locate, or its length has to be controlled. It costs more per part and it is the correct answer far more often than the stamped version.
  • Where the two are genuinely equivalent is a reducer whose bore is a plain clearance hole and whose OD is a loose fit in a large hole – for example a spacer or a blanking reducer on a panel. In that case the stamped version is entirely adequate and the tighter machining is wasted money. So the question to ask is what the reducer’s bore actually does.

Inspection of the flow path

On a reducer that carries fluid, the bore is a flow surface and there are three items that are specific to it.

  • The bore’s internal surface finish. It affects the fitting’s entry and, on a smaller bore, the pressure drop. On a reducer that is merely a blanking plug it does not matter; on one that carries flow it is worth stating.
  • The bore’s lead-in’s form. A lead-in that is a simple chamfer is right for most applications. A countersink or a radius is right where the mating part’s entry needs centring. And on a threaded bore, the thread’s entry chamfer is a separate feature from the bore’s lead-in – they are concentric but they have different diameters and different jobs.
  • Burrs at the bore’s exit and at the thread’s mouth. On a brass or aluminium reducer the thread’s mouth will burr, and on a part that will be assembled repeatedly a burr at the thread’s first turn will prevent a clean start and will gall. It is a small item and it is a real one.

It is also worth asking whether the reducer’s bore has to be inspected for cleanability. A reducer is normally upstream of whatever it feeds and it is often installed before any of the system’s own filtration, so in a hygienic or a pharmaceutical installation it is a product-contact part and the same internal geometry rules apply as on a sanitary fitting: no internal step, no square internal corner, and a defined internal finish.

Eight items that turn a spacer into a specified component

Eight items, in the order they matter, and the first three are what turn the reducer from a spacer into a specified component.

  1. What the bore is for – a threaded connection, a clearance hole, a blanking plug, or a flow passage. Every other dimension follows from this and it is the item most often missing.
  2. The OD stated as a fit to the mating hole, with the mating part named, and the fit agreed rather than chosen independently.
  3. Whether dimensions are before or after finish, and the masking list, with the bore’s thread and any locating diameter named.
  4. The thread’s standard, class and gauge, in the finished condition.
  5. Concentricity of the bore to the OD and to the hex flats, as a relationship.
  6. Width across flats as a fit to the wrench, and the corner condition.
  7. Both chamfers – the bore’s lead-in and the OD’s – with their angles and diameters.
  8. Length, and whether it includes the thread, stated, because the convention is not universal and a 2 mm difference decides whether the reducer seats.

Inspection, and the two fits tested separately

  1. OD size, roundness and cylindricity, measured, and the fit checked as a fit.
  2. Thread gauging on every part where the bore is threaded.
  3. Concentricity of the bore to the OD, measured on the CMM.
  4. Width across flats and the corner condition, – a wrench fit, verified as such.
  5. A functional fit check into a representative mating hole, on a sample. On a reducer this is the single most informative inspection: it tests the OD, the concentricity, the length and the lead-in together, in seconds.
  6. Finishing thickness and adhesion on the first article, with the masked thread and any masked OD verified.

Driven, screwed, or simply dropped in

Is this reducer going to be driven in, or screwed into place by its hex, or just dropped into a hole and held by the fitting’s thread? Those three arrangements produce the same-looking part and they have quite different requirements. A driven bushing needs an OD with enough hardness not to ovalise and a lead-in that will not wedge, and it will need a tighter OD fit because a driven joint’s tolerance is consumed by the driving. A bushing held by its hex needs a hex that can transmit torque and that will not round, and the hex becomes a strength feature. A bushing simply located by the hole and loaded by the fitting’s own thread needs the least – a general fit, a good lead-in, and a bore that seats. It is worth also asking whether the hole this reducer goes into is controlled by the same drawing. If it is not, the reducer’s OD tolerance has to be agreed with whoever owns the hole rather than chosen independently, and that conversation is much cheaper before the parts are made than after the first batch does not fit.

Request a Quote for This Part

Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).