What is an Auto Starter? Components Explained

Wiper Motor Components 2

What is Auto starter ?

2026-09-27 07:24:47 larryzhang

A starter is an electric motor built for a job that lasts a few seconds and has to be repeatable for the life of the vehicle. It turns the engine over until the engine runs on its own, then it gets out of the way. That duty cycle – very high current, very short duration, thousands of repetitions – is what makes its components different from the parts inside a motor that runs continuously.

When the key turns, battery current energises the solenoid. The solenoid does two things at once: it pushes the pinion gear forward to mesh with the ring gear on the flywheel, and it closes the heavy contacts that feed the motor itself. The motor then cranks. Once the engine fires, the engine is spinning faster than the starter can drive the pinion, so the pinion has to be released – that is what the overrunning clutch is for, and without it the engine would drive the starter to destruction in a few seconds.

The drawn parts in a starter are the motor housing, the end cap and the pinion housing. The motor housing is a deep can: it carries the field assembly, it closes the magnetic circuit, and it has to hold the pole shoes in position relative to the armature, so its bore and its length are the dimensions that matter. The end cap carries the brush gear and the shaft bearing, which means the relationship between its bearing seat and its mounting face is the functional stack. The pinion housing locates the drive and has to keep the pinion aligned with the ring gear it engages.

These parts are specified in low-carbon steel for magnetically soft reasons: the housing is part of the magnetic circuit, and a material that carries flux poorly costs torque. Where the housing is also exposed to road salt, it is protected afterwards, and that protection is chosen so it does not build up on the surfaces the pole shoes seat against, because a coating there changes the air gap and the air gap is a motor design parameter.

The problems that come back on starter parts are rarely dimensional. They are a housing that was drawn too thin and deforms when the through-bolts are tightened, an end cap whose bearing seat is not concentric with the shaft and wears brushes unevenly, or a pinion housing that lets the drive sit slightly out of line and chips the ring gear. Each of those is a relationship between features rather than a size, which is why we hold the concentricities and the squareness as the critical dimensions on this family.

How a starter works, in one minute

A starter motor does three things in sequence inside about two seconds: engage, crank, disengage. The solenoid does the engaging — battery current throws a plunger that pushes the pinion gear forward into mesh with the ring gear on the flywheel, and the same plunger closes the heavy contacts that feed the motor. The motor then cranks the engine: brushes riding on the commutator switch current through the armature windings against the field, and the shaft turns. Once the engine fires and spins faster than the starter can drive it, the overrunning clutch releases the pinion so the engine drives nothing at all, and a return spring pulls the pinion back out of mesh. The drawn parts sit in the middle of that sequence — the motor housing around the field, the end cap at the brush end, and the pinion housing around the drive.

Why the housing is part of the motor, not just a cover

On a starter, the housing is a magnetic component as much as a mechanical one. The field windings sit between the housing wall and the armature, and the steel housing closes the magnetic circuit: flux leaves a pole shoe, crosses the air gap into the armature, and returns through the housing wall to the next pole. That makes the wall part of the flux path. A material that carries flux poorly, or a wall drawn thin and distorted, costs torque — and torque at the flywheel is what the driver feels as cranking speed on a cold morning. The same wall also carries heat away from the field windings during the seconds-long current surge, which is why wall-thickness uniformity matters more here than on a cover that never sees current. Every starter motor housing we draw is specified against these flux-path and concentricity requirements, not just against a diameter and a length.

Material: magnetically soft first, drawable second

Starter housings are specified in low-carbon steel for both reasons at once. The chemistry keeps the steel magnetically soft, so it carries flux without holding residual magnetism that would bleed performance between cranking attempts; and draw-quality grades give the deep, seamless can the formability the geometry demands. Aluminium is lighter, but it cannot carry the return flux, so it shows up in brackets, solenoid covers and heat shields — never in the flux path. Corrosion protection is applied afterwards, and the specification deliberately keeps the pole-shoe seating band bare: coating build-up there changes the air gap, and the air gap is a motor design parameter, not a finish detail.

The dimensions we hold as critical

Most starter part problems are relationships, not sizes. On the motor housing we control the bore and its cylindricity, because the field assembly has to sit concentric to the armature. On the end cap we control the concentricity of the bearing seat to the shaft centreline and the squareness of the mounting face to the bore, because that stack decides how evenly the brushes wear over thousands of starts. On the pinion housing we control the alignment of the drive bore to the mounting interface, because a drive sitting a fraction of a degree out of line chips ring-gear teeth. Wall uniformity through the pole-shoe band is measured section by section, and the brush-gear edge is deburred to a defined limit so the brushes hang up on nothing. Each of these appears on the inspection report as a held characteristic with a stated method — not as an assumption inherited from the drawing.

From blank to shipment

The process for a starter can is short but unforgiving: blank and lubricate, draw — one pass for shallow housings, two or three with an intermediate anneal for the deep cans — trim to length, pierce the mounting and connector features, deburr, then plate. The limiting draw ratio decides how many passes a given depth needs, and our limiting draw ratio reference lays out first-draw limits by material with the test conditions stated. Prototype tooling typically takes 2–4 weeks and production tooling 4–8 weeks, depending on draw depth, number of stations and surface treatment. After that the programme runs from pilot batches of around 1,000 pieces up to multi-million-piece annual volumes, with lot-level traceability from coil to shipment.

What we need to quote a starter part

A starter drawing usually carries the functional stack, not every dimension we hold. To quote, we look at the bore and length, the mounting interface, the wall thickness at the pole-shoe band and the finish specification; if any of those are open, we ask before tooling rather than assume. Where the drawing is silent on concentricity or squareness, we propose values from comparable starters and mark them for your review — that stack is a design decision, and it is better settled on paper than discovered at first-article inspection.

Starter covers and shields are thin-gauge parts, so draw depth limits them before tonnage does. The material selection guide covers the low-carbon and 300-series grades these parts are usually drawn in, and the deep drawing process covers the press schedule behind a thin-gauge shell.

Frequently Asked Questions

What material are starter motor housings made from?

Low-carbon steel, specified magnetically soft so the housing can close the field circuit without retaining residual magnetism, in draw-quality grades that form the deep seamless can. Corrosion protection is applied afterwards and kept off the pole-shoe seating band so the air gap is unchanged.

Can a starter housing be made from aluminium?

Not the motor housing. The housing is the return path for the magnetic field, and aluminium cannot carry it — a starter built around an aluminium can loses torque. Aluminium is used for brackets, solenoid covers and heat shields, where no flux flows.

Which tolerances matter most on a starter housing?

Bore diameter and cylindricity on the motor housing; bearing-seat concentricity and mounting-face squareness on the end cap; drive-bore alignment on the pinion housing. These relationships, rather than individual sizes, decide whether the starter cranks cleanly and wears evenly.

How are starter housings protected against road salt?

Zinc plating over the drawn steel is the standard protection, with an organic top-coat where the environment calls for it. The plating mask deliberately leaves the pole-shoe seating band bare, because build-up on that band would change the air gap and cost torque.

What production volumes can you supply?

From pilot runs of around 1,000 pieces to multi-million-piece annual programmes on high-speed presses, with lot-level traceability on every shipment.

How long does starter tooling take?

Prototype tooling typically takes 2–4 weeks and production tooling 4–8 weeks, depending on draw depth, the number of stations and the surface treatment specified.

Which drawn parts sit inside a starter motor housing?

The can or yoke, the end cover, and the shields around the commutator end. Most are thin-gauge low-carbon steel or aluminium, drawn or stamped depending on depth, then pierced and trimmed. They see very high current for a few seconds at a time, so the dimensional concern is concentricity and fit rather than long-term wear.

Related reading

Limiting Draw Ratio (LDR) Reference for Deep Drawn Parts — first-draw limits by material with stated test conditions, wall-thinning data and a blank diameter calculator.

Further Reading & Standards

The engineering claims on this page are grounded in the measurement methods and classifications maintained by these organisations. We apply the same methods on the shop floor for every order.

  • ASTM E517 — Standard Test Method for Plastic Strain Ratio (r) of Sheet Metal. The r-value predicts earing in drawn cups.
  • DIN 8584 — Manufacturing processes, forming: classification of deep drawing operations and their subgroups.
  • ISO 20482 — Metallic materials: Erichsen cupping test, a formability measure complementary to LDR.
  • Wikipedia: Metal forming — the broader process family these limits sit within.
  • Wikipedia: Sheet metal — material grades, gauge and formability background.

Key point: A starter motor is a short-duty, high-current electric motor; the deep-drawn parts in it are the housing and the cover, not the windings.

What we do not claim: We do not publish leak-rate figures, autoclave cycle counts or springback angles that we have not measured. The ±0.02 mm figure applies to ironing passes only, not to every geometry. 6xxx aluminium is used for shallow forming, not deep drawing. Prices, minimum order quantities and lead times are confirmed per drawing rather than published as fixed values.

Last reviewed: 2026-11-05 · Reviewed by Sam Zhang, Process Engineer

Similar Posts