
A light housing is a reflector, and a reflector is judged by what it does with light
A deep drawn steel light housing, zinc plated, is a deep drawn shell with a reflective interior. That single phrase contains the whole engineering problem: the housing must be a structure, it must survive a mounting environment, and its interior surface must perform a photometric function. The reflective interior is what makes it a light housing rather than a can, and it dictates requirements – surface finish, geometry, no burrs, no contamination – that the structural part would never have.
We multi-stage draw with interstage annealing, trim and pierce in following dies, and in-process checks between stages, on mechanical presses 5-250 T and hydraulics 250-500 T with in-line annealing furnaces, backed by CNC turning centres and a climate-controlled inspection room. Drawn diameters to +/-0.05 mm with tighter bands confirmed against the drawing, and critical dimensions carrying CMM data with the shipment. Carbon steel, 304 and 316 stainless steel, aluminium and brass are all held in stock, with the final grade fixed at the drawing review. Natural, plated or coated per the print, with the agreed finish logged and finish thickness and adhesion checked on the first article. This page is about the interior surface, the geometry that shapes it, and the conflict between the two.
The interior surface is the product
On a light housing, the interior surface does the work of reflecting or containing light, and four requirements follow, none of which would apply to a structural housing:
- Uniformity. A reflector or diffuser interior has to be consistent along its length and around its circumference. On a drawn housing, consistency is challenged by the draw’s own variation – the wall thins unevenly, the surface has draw lines, and a plated surface’s thickness varies. A variation in the interior surface shows up as a variation in light output, which is visible.
- No burrs, anywhere. This is the requirement people forget. A burr inside a light housing is a scattering centre – it catches light and produces a bright spot or a dark artefact that is immediately visible. On any housing where the interior is seen, a burr is a defect regardless of its size, and the deburring requirement here is a quality requirement rather than a handling one.
- No contamination and no drawing lubricant. A drawn steel part carries drawing lubricant and possibly an anneal oxide. On a reflective interior, that is visible as haze, and on a high-output fixture it will reduce output and change the colour of the light. A cleaned, degreased interior is a requirement, and where the interior will be visible it should be a stated process step.
- Corrosion resistance on the interior. A zinc-plated housing’s interior will eventually corrode if it is not protected, and corrosion on a reflective surface is both a light-output and an appearance problem. Where the interior is not plated – and plating the interior of a drawn part is harder than plating the outside – the corrosion protection has to come from somewhere else.
Geometry, which is the designer’s real tool
Since the material and the finish are nearly fixed, the light output is set by the housing’s geometry, and several geometric decisions have outsized effects:
- The diameter tolerance matters photometrically. Drawn diameters to +/-0.05 mm is the stated band, and on a reflector the diameter changes the light’s exit angle. A reflector whose diameter varies by a tenth of a millimetre varies its output angle by a small but real amount, and a batch of housings with a wide diameter spread produces a batch of fixtures with a spread of output. Where the housing sets a beam angle, the diameter is a functional tolerance and should be flagged.
- The draw’s material flow and the reflector’s curvature do not want the same thing. A deep draw wants generous radii and a smooth flow; a tight reflector curve wants small radii and a specific shape. Where a design needs both, the second operation is usually a forming operation to set the optical geometry after the shell is drawn – and that should be in the process plan rather than left to emerge from the draw.
- Wall thickness variation changes the reflection. A drawn wall thins toward the punch nose, so a deep housing’s wall is thinnest at its bottom. A varying wall affects how the housing deforms and can produce visible distortion in the reflective surface. On a shallow housing this is minor; on a deep one it is not.
- The mounting features and the optical features are usually in tension. The mounting feet, the screw holes, the bracket fixings all want to be on the housing, and all of them are visible from the wrong side. Every one of them inside the housing is a light blockage and a shadow.
Zinc plating, and the interior problem
Natural, plated or coated per the print, with the agreed finish logged and thickness and adhesion checked on the first article. On a light housing, zinc plating is a good answer for the exterior and a complicated one for the interior:
- Plating the interior is a barrel operation or a rack operation, and a rack operation – where the part is hung on a fixture at a defined point – leaves a contact mark and a locally uncoated area. On a reflective interior, a contact mark is a visible defect. Barrel plating is the answer for a small housing, and it requires the part’s dimensions and its features to be compatible with being tumbled in a barrel without marking each other.
- Plating thickness changes the interior’s geometry. A zinc layer on a draw mark fills it partially; on a tight radius it rounds the corner slightly. On a reflector, that is a small but real change to the optical geometry, and it should be established rather than assumed.
- Where the interior is not plated, a corrosion-resistant base material or a coating applied by another route is needed. This is a real decision, and the honest options are: plate the interior by a suitable method, use a stainless steel or aluminium base, or accept that the interior will corrode and specify a maintenance interval.
- Masking the mounting features, where a screw goes through and must not be plated, is a per-part operation and belongs in the cost.
A light housing is decided by its interior and its environment
Carbon steel, 304 and 316 stainless steel, aluminium and brass are all held in stock, with the final grade fixed at the drawing review. For a light housing the choice is driven by the interior and by the environment:
- SPCC or DC01 carbon steel with zinc plating is the standard, and it is the right answer for a general indoor or sheltered fixture. It is cheap, it forms well, and the plating gives both appearance and corrosion resistance. It is the workhorse of this part type.
- Aluminium where the housing is a reflector – because aluminium’s reflectivity is high and it does not need a reflective coating – or where mass matters, or where an anodised finish is wanted. Anodising on aluminium gives a hard, clean surface that is itself reflective if the anodising is thin, and it is dimensionally very well behaved. On an optical part this is often the best answer.
- 304 or 316 stainless steel where the environment is corrosive, or where a bare bright interior is wanted without plating. Stainless Steel’s reflectivity is lower than polished aluminium’s, and its interior will show the draw lines, so a drawn stainless steel interior generally needs polishing or a reflective coating to perform well.
- Brass is rare here except for decorative or marine fixtures where its warm appearance is intentional.
If the housing is not doing the optical work
Eight things, and the first four are optical requirements rather than structural ones:
- Which surfaces are optical, and what reflectance is required on them, including whether the interior is plated, polished, anodised, or bare.
- Burr and cleanliness requirements on the interior, with a stated burr limit rather than the word deburred.
- Diameter tolerance flagged as photometric, where the diameter sets the light’s exit angle.
- Whether the interior surface’s draw lines are acceptable or whether a second forming or polishing operation is required to produce the optical geometry.
- Which features inside the housing are allowed, and which must be relocated outside because they block or scatter light.
- Corrosion protection for the interior, stated – plated, passivated, or a maintenance requirement.
- Which surfaces are masked and whether dimensions apply before or after plating.
- Wall thickness, and where the minimum is, since a deep housing’s wall thins toward its bottom and that affects the reflective surface.
Is the housing doing the optical work, or holding a reflector?
Is the housing actually doing the optical work, or is it just holding a reflector? Where the housing’s interior is meant to be the reflector, the whole part is an optical component and should be specified as one – which usually means a second operation to form the optical surface, and a material whose base reflectivity is adequate. Where the housing only contains a separate reflector or a diffuser, it is a structural and cosmetic part, the interior requirements reduce to corrosion protection and cleanliness, and the drawing can be much simpler and the part much cheaper. Settling which of these the product is, before the tooling is committed, is the single most valuable thing that can be done on this part.
If you are weighing drawing against machining or welding for this geometry, the guide to deep drawn covers sets out where each route wins; the full Precision Deep Drawn Parts range is linked from the overview page.
Specifications
| Item | Deep Drawn Steel Light Housing, Zinc Plated |
|---|---|
| Brand | AUNOV |
| Designing | Driven by your drawing or a physical sample – a manufacturability review comes back with the quotation; revisions are re-quoted once rather than silently absorbed. |
| Tooling | Dies, fixtures and gauges are made in our own toolroom, so no tooling step is outsourced, and maintenance is tracked against the part number. |
| Samples | Free samples are available on standard items, with reports attached. |
| Materials | Carbon steel, 304 / 316 stainless steel, aluminium and brass are all held in stock; the final grade is fixed with the drawing review. |
| Surface finish | Natural, plated or coated – the print decides, and the agreed finish is logged; finish thickness and adhesion checked on the first article. |
| Processing | Multi-stage deep drawing with interstage annealing, trimmed and pierced in following dies; in-process checks sit between stages, not only at the end. |
| Equipment | Mechanical presses from 5 to 250 T and hydraulic presses 250-500 T, with in-line annealing furnaces, backed by CNC turning centres and a climate-controlled inspection room. |
| Tolerance | +/-0.05 mm on drawn diameters, tighter bands confirmed against the drawing; critical dimensions carry CMM data with the shipment. |
| Delivery terms | FOB, with DDP offered for EU and US addresses, payment by T/T, L/C at sight or D/P; call-off schedules are supported. |
Frequently Asked Questions
Why is the interior surface the product on a light housing?
The housing must be a structure and survive mounting, but its interior must perform a photometric function – reflect light. That makes surface finish, geometry, burr-free edges and cleanliness requirements the structural part would never have.
What does zinc plating do on the interior of a light housing?
Zinc plating provides a bright, corrosion-resistant base on the interior that supports the reflective function in the mounting environment, and its thickness and adhesion are checked on the first article. The interior is kept contamination-free through handling.
Which materials suit a light housing?
Carbon steel, 304 and 316 stainless steel, aluminium and brass are held, with the grade fixed at the drawing review. Drawn diameters are held to +/-0.05 mm with tighter bands confirmed against the drawing.
How is a light housing quoted and verified?
Multi-stage drawing with interstage annealing and pierced features, in-process checks between stages, and CMM data travelling with the shipment. The typical minimum order is 1,000 pieces with a 24-hour quotation.
Related Products
Request a Quote for This Part
Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).




