Cooling pump electric motor housing

Cooling pump electric motor housing
Cooling pump electric motor housing

The housing behind the casing: motor chamber and bearings

On an electric coolant pump, the cooling pump motor housing is the structural shell that holds the stator, locates the rotor bearings, and (in a wet-rotor design) often runs with coolant on both sides of the can. Where the outer casing is primarily the sealing and mounting envelope, the housing is the part that carries the mechanical loads – and it is judged on stiffness, roundness, and bearing-seat accuracy rather than on sealing alone.

We draw these housings from 1.4301 or 1.4404 stainless steel, sized to take the stator with a controlled interference and to hold the bearing bores concentric over the operating temperature range.

Wet-rotor versus dry-rotor: two very different housings

The architecture decides almost everything about the housing:

Wet rotor (canned)The rotor runs in coolant; the stator is outside a thin can. No dynamic shaft seal, which removes the most common leak point – but the housing must be coolant-compatible internally, and the rotor bearings run in the fluid, so the housing’s bore accuracy directly sets bearing life.
Dry rotorA shaft seal separates the wet pump chamber from a dry motor. The housing sees the pump’s axial and radial loads through the shaft seal and bearings, so it must be stiff enough to keep the two bores aligned under load.

Because the wet-rotor design is common in modern automotive coolant pumps, most of our housings are specified for coolant contact on the inside, with material and passivation chosen accordingly.

Bearing seats: the roundness that decides pump life

In a small high-speed pump, the bearings are the life-limiting component, and they depend on the housing:

  • Bore roundness and concentricity. A bore that is out of round or eccentric to its partner loads the bearing unevenly, generating heat and noise. We hold concentricity between bearing bores to 0.03-0.06 mm TIR on a good die and keep roundness within a few thousandths.
  • Coefficient of expansion. Stainless Steel expands less than an aluminium housing would, which helps the bearing fit stay stable over temperature – one reason stainless steel is preferred even though it costs more and conducts heat less well.
  • Seat finish. A rough bore frets against the bearing outer ring and wears it. We control Ra on the seat and avoid over-coining that work-hardens the surface.

Stiffness, vibration, and the pump’s acoustic signature

A coolant pump is small but runs at high speed, often with a variable-speed drive, which means it passes through resonances as it ramps. The housing’s stiffness and mass set where those resonances fall:

  1. A stiff, round housing pushes resonances up and keeps the rotor-to-stator gap stable, which reduces both vibration and current ripple in the motor.
  2. A flexible or oval housing lets the gap vary, which produces a once-per-revolution force and audible whine – a common complaint on electric coolant pumps.
  3. Wall damping is limited in a thin metal housing; where noise is critical, we work with the customer on wall thickness and any added ribs or a damping layer.

Pressure and circulation inside the housing

In a wet-rotor pump, coolant circulates through the housing to cool the stator and lubricate the bearings, so the housing often has internal passages or openings that control the flow path. Those features have to be formed or pierced without creating a leak path to the dry side and without disturbing the bore roundness. We keep coolant passages away from the bearing bores and, where the flow path runs axially, form it in the wall rather than through a joint.

A coolant pump housing carries bearing loads in a thicker wall

  • Diameter: 25-60 mm, matching auxiliary and main coolant pump motors.
  • Length: 30-110 mm.
  • Wall: 0.8-1.8 mm; thicker where the housing carries bearing and shaft loads.
  • Features: stator bore, bearing seats, coolant ports, mounting interface, end-cap seat.

Aluminium housing, and the expansion mismatch that comes with it

Can the housing be aluminium for weight and heat rejection?

Possible, but the expansion mismatch with the bearing and the galvanic risk in coolant argue for stainless steel in most designs. We will model both if you want the comparison.

How do you hold two bearing bores concentric in a drawn housing?

By drawing to a round bore and, where needed, a single final sizing or a light boring operation on the critical seats; the die alone can hold concentricity across a short housing but long housings need the extra step.

Does the housing need passivation if coolant only touches the outside?

If coolant touches any surface that carries the stator or a seal, yes – the same corrosion logic applies wherever the fluid reaches metal.

Can the housing carry the mounting bracket?

Yes, where the design integrates them; a formed bracket removes a joint and a fastener, at the cost of more complex tooling.

Specifying a coolant pump motor housing

Tell us the rotor architecture (wet or dry), the bearing type and its required bore accuracy, the stator interference, the coolant flow path, the mounting loads, and the acoustic target. Those inputs let us size the wall for stiffness, hold the bores for bearing life, and choose a material and finish that survive the coolant – which is what makes a coolant pump housing a durable part rather than a short-lived one.

This part belongs to our Automotive Motor Components range. The automotive motor components pages collect the process notes, common materials and inspection points behind every product in the family.

Specifications

ItemCooling pump electric motor housing
BrandAUNOV
DesigningDriven by your drawing or a physical sample – unusual walls, threads or tolerances are feasibility-checked first; the agreed version governs every later batch.
ToolingProgressive and drawing dies are designed and built in house, so tooling lead time stays under our control, and ownership is confirmed on the quotation.
SamplesSamples are issued for approval before the run, so the sample is retained as the master, and the signed sample is kept for future reorders.
MaterialsCarbon steel (SPCC / DC01), 304 / 316 stainless steel, aluminium, brass and copper – the grade is matched to the duty of this housing.
Surface finishPhosphating first for coating adhesion, then powder coating, e-coating or zinc plating; chrome and nickel are reserved for visible faces.
ProcessingCoil blanking, progressive drawing through 3-5 stages with anneals between, trim and pierce, then deburr and finish.
EquipmentMechanical capacity 5-250 T and hydraulic 250-500 T, with annealing ovens and CNC turning and machining centres alongside.
Tolerance+/-0.1 mm to +/-0.2 mm general; critical features held to the drawing and verified on the first article.
Delivery termsFOB, CIF or DDP per Incoterms 2020, T/T or L/C, with D/P accepted on repeat business; price breaks tie to annual volume.

Request a Quote for This Part

Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).