Deep Drawing Design Guide: Tolerances & Materials
What is deep drawing?
Deep drawing is a sheet-metal forming process that turns a flat blank into a seamless shell through a fixed sequence of press operations.
Deep Drawing
Deep drawing is one of the most widely used processes in sheet metal forming. Apart from its use in many other sectors, it is applied in the automotive industry for the manufacturing of car body parts.
Process definition:
The deep drawing process is a forming process which occurs under a combination of tensile and compressive conditions. A flat sheet metal blank is formed into a hollow body open on one side or a hollow body is formed into a hollow body with a smaller cross-section.
Deep drawing processes are divided into three types:
Deep drawing with tools
Deep drawing with active means
Deep drawing with active energy
In the automotive industry, deep drawing is usually carried out using rigid tools.
The figure illustrates the deep drawing process. The rigid tools consist of a punch, die and binder. In deep drawing, the plate holder closes after the metal sheet blank has been inserted.
Next the sheet is clamped between the die and the binder. This process slows down the flow of the sheet while it is being drawn and thereby prevents wrinkles from forming under the binder. The punch stretches the sheet over the die radius and forms it in the die. The amount of punch force necessary for forming is thereby continually increased up to the lower dead center of the punch.
Whereas in pure deep drawing there is no reduction of sheet metal thickness, forming is achieved in stretch forming purely as a result of a decrease in sheet metal thickness. Stretch forming is extensively used for the forming of only slightly curved parts with low depth of draw (e.g. roofs, doors).
When drawing complex car body parts in practice, there is usually a combination of stretch and deep drawing involved. It is necessary that the sheet metal is stretched as well as possible without reaching the material’s limits (e.g. splits, wrinkles).
There are approximately 300 to 400 sheet metal parts which fit together to form the body of a car. In order to manufacture high quality sheet metal parts optimally for their particular use, specialized software simulates the complete deep drawing process.
Deep drawn parts from our presses
Limiting Draw Ratio (LDR) Reference for Deep Drawn Parts — first-draw limits by material with stated test conditions, wall-thinning data and a blank diameter calculator.
Deep drawing at a glance
Deep drawing forms a seamless metal shell from one flat blank in a single press line. Production typically runs on presses from 5 to 500 tonnes, forms wall thickness from 0.15 to 3.0 mm, and holds diameters and heights to about ±0.05 mm (±0.02 mm with ironing). One draw can reach a limiting draw ratio around 2.0; deeper parts add redraws with intermediate anneals. Parts are produced up to about 150 mm deep. Minimum order quantity is usually 1,000 pieces, and a feasibility quote is normally returned within 24 hours.
How the sequence runs, from blank sizing through redraw stages and intermediate annealing, is covered in the deep drawing process. What matters on this page is the design side: how those stages constrain the wall thickness, radius and tolerance you can ask for.
Materials Commonly Deep Drawn
Design Guidelines for Deep Drawn Parts
A few rules prevent most drawing problems, and all of them are cheap to apply at the design stage:
- Keep corner and punch radii generous relative to material thickness — sharp corners crack.
- Limit draw depth relative to diameter; check the ratio against a limiting draw ratio reference before freezing the design.
- Avoid walls thinner than about 0.3 mm on deep parts unless function demands it.
- Tolerance only the surfaces that matter; everything else should carry a general tolerance.
- Design features that can be coined into the draw rather than machined afterwards.
- Remember springback: stainless steel springs back more than aluminium or mild steel.
The geometry you choose places the part in a difficulty tier that drives tooling and piece price; see simple, average and difficult deep drawn geometries for how that classification works.
Tooling and Try-Out
A draw die is more than a punch and a cavity. The blankholder force, the die radius, the clearance between punch and die and the lubrication all interact, and they are settled during try-out rather than on paper. That is why the first article from a new tool is a process milestone, not just a sample.
Practical consequences for buyers: tooling is a real upfront cost that has to be amortised, the first article usually takes longer than repeat orders, and design changes after the tool is cut are expensive. Getting the geometry right before tooling starts is by far the cheapest quality decision available.
Quality and Inspection on Drawn Parts
Drawn parts are checked on the dimensions that matter — diameter, wall thickness, height and any formed feature — plus visual criteria for wrinkles, splits and surface marks. Because the process repeats, inspection is usually planned around agreed sampling and gauges rather than measuring every piece.
Common failure modes are known and mostly preventable: wrinkling in the flange when blankholder force is too low, splitting at the punch radius when the draw is too severe, and wall thinning that exceeds the specification on deep parts. Each has a design-side fix, which is why early supplier feedback is worth asking for. See designing small deep drawn parts for the design rules that prevent them.
How Deep Drawing Differs From Spinning and Stamping
Stamping cuts and bends a blank in one stroke and suits flat or shallow forms; spinning forms an axisymmetric shape from a rotating disc at low volume and large diameter. Deep drawing is the only one of the three that produces deep, seamless, repeatable shells at production volume. The full comparison, die casting included, is in stamping vs deep drawing vs die casting.
Choosing a Supplier for Deep Drawing
Drawing is a process where experience shows up in the quote. Three things separate a capable supplier from an optimistic one: in-house tooling, because the die is where the process is actually proven; a stated range of press capacity, because that sets the size and thickness you can run; and a willingness to give design feedback before the order, because that is where the savings are.
Getting Started With a Drawing
You do not need a finished production model to start a conversation. A 2D drawing with material, wall thickness, Critical dimensions and estimated annual quantity is enough for a supplier to confirm whether the part is drawable, how many stages it needs, and what the tooling and piece price would be. That early answer is free, and it is the cheapest way to find out whether your geometry is in the simple, average or difficult tier before you commit to it.
| Material | Drawability | Typical use |
|---|---|---|
| Low-carbon steel | Very good | Structural housings, brackets, covers |
| Stainless steel (304 / 316) | Good, work-hardens | Sensor housings, food and medical parts |
| Aluminium | Excellent | Lightweight enclosures, reflectors |
| Brass and copper | Excellent | Electrical contacts, conductive shells |
Each alloy behaves differently in the die, which is why our material selection guide for deep drawing treats formability, finishing and cost together rather than separately.
Frequently Asked Questions
What is deep drawing in simple terms?
Deep drawing presses a flat sheet metal blank into a die with a punch so the metal flows into a seamless hollow shape. Unlike cutting or welding, the part is formed from one piece of material, so there is no seam and the wall thickness stays continuous.
What materials can be deep drawn?
Low-carbon steel, stainless steel, aluminium, brass and copper are all routinely deep drawn, and nickel alloys are possible for high-temperature service. The practical limit is set by how much the material work-hardens before it needs annealing.
How many draws does a typical deep drawn part need?
Most parts are drawn in one or two operations. Where depth relative to diameter exceeds the first-draw limit, redraws are added — usually with an intermediate anneal — until the final wall and height are reached.
What radius should I design at the bottom of a drawn cup?
Start at one material thickness for mild steel and about 1.5 times thickness for 304 stainless steel. Tightening the radius below that concentrates strain at the punch nose and is the most common cause of splits, so anything sharper should be treated as a tooling question rather than a drawing note.
What tolerances can deep drawing hold?
Diameters and wall thicknesses are held consistently once the draw schedule is proven, but very tight features usually need a sizing or machining pass. Tolerance only the dimensions that functionally matter to keep cost down. For the numeric tolerance bands and the ironing figure, see our deep drawing capacity page.
This guide covers the engineering side — materials, tolerances, design rules and how to choose a supplier. For the shop-floor view of the process itself, including press tonnage, the draw schedule and the defects that signal trouble, see The Deep Drawing Process.
Standards & Further Reading
The process limits and material behaviour described here follow the test methods and definitions published by the standards bodies below. We measure every production lot against these methods and report the actual values, not catalog averages.
- ASTM E517 — Standard Test Method for Plastic Strain Ratio (r) of Sheet Metal. The r-value quantifies directional ductility and predicts earing in drawn cups.
- ASTM E646 — Standard Test Method for Tensile Strain-Hardening Exponents (n) of Metallic Sheet Materials. The n-value sets how much a wall can thin before necking.
- DIN 8584 — Manufacturing processes, forming: classification of deep drawing operations and their subgroups.
- Wikipedia: Deep drawing — process overview, terminology and tooling fundamentals.
- Wikipedia: Sheet metal — material grades, gauge and formability background.
Key point: Deep drawing forms a flat blank into a seamless shell in one press line, so the wall and the base stay one continuous piece of metal.
What we do not claim: We do not publish leak-rate figures, autoclave cycle counts or springback angles that we have not measured. The ±0.02 mm figure applies to ironing passes only, not to every geometry. 6xxx aluminium is used for shallow forming, not deep drawing. Prices, minimum order quantities and lead times are confirmed per drawing rather than published as fixed values.
Last reviewed: 2026-11-05 · Reviewed by Sam Zhang, Process Engineer
