
Machining plastic and metal together is a materials problem that looks like a process question
A custom CNC machined part in plastic or metal looks like a process description, and it is really a materials selection. The two material families behave so differently in machining that “plastic or metal” is not a single subject – it is two, and the choice between them changes almost every decision on the drawing. The same geometry in acetal and in stainless steel is two different parts, and the tolerance scheme, the surface finish, the tooling, and the design rules all follow from which one is chosen.
We machine these from bar or billet with concentricity held across operations, and every stage is logged against your part number, on 12 CNC turning centres with automatic bar feeders, with in-house toolmaking keeping dies and fixtures maintained. General tolerance is +/-0.02 mm with tighter bands on flagged dimensions, and dimensional reports accompany the first article. Standard stock is carbon steel in SPCC and DC01 grades, 304 and 316 stainless steel, aluminium and brass, with mill certificates and heat numbers accompanying the first article. Finish is selected from the drawing – plating, coating, anodising or passivation – with alternatives quoted alongside and samples approved in writing. This page is about what changes when the material family changes, and the four requirements that are fundamentally different between the two.
Why this is a materials question, not a process question
Four things behave so differently between a plastic and a metal that they change the design rather than the machining parameters:
| Thermal behaviour | A metal conducts heat away from the cut and stays dimensionally stable while machining. A plastic does not – it heats locally, it softens, and it expands. The consequence is dimensional: a plastic part measured at room temperature after a heavy cut is not the same shape as one measured after it has cooled, and a tolerance tighter than the material’s thermal movement is asking for something the material cannot give. This is why plastics in this family are usually specified with a looser general tolerance and a tighter one only on dimensions that are insensitive to temperature. |
|---|---|
| Elastic behaviour | A metal is stiff and deforms very little under a cutting force. A plastic is several orders of magnitude less stiff, so a slender feature deflects under its own cutting force, moves, and can chatter or be pulled out of tolerance. A thin-walled plastic feature is a design problem that a machinist cannot solve, and the answer is a thicker wall, a shorter overhang, or a different material. |
| What the material can hold | A metal holds a fine thread, a tight tolerance, and a hard edge. Most engineering plastics hold a coarse thread, a modest tolerance, and a soft edge. So on a plastic part, thread design, bearing surfaces, and sealing faces all have to be designed differently – a plastic thread is a buttress or a trapezoidal form because a V-thread relies on the material’s shear strength that plastic does not have. |
| What finishing is available | A metal can be plated, anodised, passivated, or polished. A plastic cannot – it is finished by moulding, by machining cleanly, or by a cosmetic coating. So on a plastic part the finish requirement is expressed as a surface finish on the machined surface rather than as a coating specification, and the drawing’s finish section is a different kind of document. |
Tolerance, and where the two families differ most
General tolerance of +/-0.02 mm is a machining tolerance and it is achievable in a metal with a rigid design. On a plastic part the same number may be achievable on a large, well-supported feature and completely unachievable on a thin wall. Four requirements that differ:
- Wall thickness. A plastic part needs a minimum wall that a metal part does not. Below a certain wall – which depends on the plastic, but for a typical engineering plastic is around a millimetre and can be several for a glass-filled grade – the part is too flexible to hold a dimension, too fragile to handle, and it will warp after machining. A design that works in metal frequently has to be thickened to work in plastic.
- Feature size and its distance from the part’s centre. A plastic part’s features move under cutting force in proportion to how far they are from the clamped region, so a feature at the far end of a long plastic part is less accurate than one near the clamp. On a metal part this gradient is negligible.
- Clamping. A plastic part must be clamped gently, and a thin-wall plastic part is best clamped on a feature designed to be clamped. On a metal part clamping is rarely a design consideration; on a plastic part it is one of the primary design requirements.
- Time and temperature. On a plastic part the dimensional report is only comparable if the part has cooled. A part measured immediately after machining is out and the reading is meaningless, so the inspection specification on a plastic part needs a conditioning requirement – and this is a real and frequently omitted line on a drawing.
Which plastic, and why the grade is the specification
On a plastic part the grade is not a detail. Four families cover most of what is machined, and they differ in exactly the properties that matter:
- Acetal (POM) and POM-C are the machinist’s plastics. They machine beautifully, with a good surface finish, low friction, good dimensional stability, and a low shrinkage. Acetal is the default for a small precision plastic part and it is the right answer in most cases.
- Nylon (PA6, PA66) is tough, wear-resistant, and dimensionally less stable – it absorbs moisture and swells, and its dimensional change with humidity is larger than its change with temperature. Nylon is the right choice for a wear part or a tough application and the wrong choice for a precision dimension.
- Polycarbonate is tough and dimensionally stable and is used where impact resistance matters, but it machines with more tendency to stress-whiten and crack around sharp corners, so corner radii and the tool’s condition matter more.
- PTFE is chemically inert and self-lubricating and machines acceptably, but it has a large thermal expansion and it creeps under sustained load. PTFE is the right material for a chemical or a low-friction application and the wrong one for a precision part under load.
- Glass-filled grades of nylon, polycarbonate, and PET improve stiffness and dimensional stability substantially and are worth considering where a plastic part needs to hold a dimension – at the cost of machinability, because the glass fibres are abrasive on the tool and they change the surface finish.
Metal, and the same decisions in reverse
Standard stock is carbon steel in SPCC and DC01 grades, 304 and 316 stainless steel, aluminium and brass, with mill certificates and heat numbers accompanying the first article. On a part where the material has not been decided, the metal options and their distinct advantages:
- Free-machining brass is the reference case for a small precision part. It machines fast, gives an excellent surface, resists corrosion in water and in many oils and fuels, and is available in lead-free grades. Its limit is dezincification in acidic or ammonia-bearing media.
- Aluminium 6061 where mass matters, and it is the standard for a complex part with significant milling.
- 304 and 316 stainless steel where corrosion resistance or a specific appearance applies, with 316 for chlorides. A free-machining variant is worth considering on a part where cycle time matters.
- Carbon steel where cost governs and the environment is mild, with the free-machining grades a genuine economy.
Design rules, and the four that differ
Four design habits that carry over from metal to plastic and cause failures when they do not:
- Threads. A V-thread relies on material shear. In a plastic it must be a coarse, blunt form – a buttress, a trapezoidal, or a self-tapping thread designed for the material – and the engagement length has to be greater. A metal thread specification copied onto a plastic part is the most common error in this part family.
- Snap fits. A metal snap fit relies on the material’s yield strength and a strain-hardening response. A plastic snap fit is different: it needs a lower strain, a thicker root, and often a different geometry entirely. And a plastic snap fit’s fatigue life is far lower than a metal’s.
- Sealing faces. A metal sealing face is flat and hard. A plastic sealing face creeps, and a joint that sealed at assembly may not after a month in service. On a plastic sealing application the joint’s long-term behaviour has to be considered, not just its initial compression.
- Press fits. A press fit in metal is a permanent elastic deformation. In plastic it is a creep problem – the fit will loosen, because plastic creeps under sustained load. Where a plastic part is press-fitted, the joint needs a positive mechanical lock, not friction.
Moulding wins on small precision parts, often
Eight things, and the first three are what make a plastic-metal part reviewable at all:
- Which material, by name and grade, and on a plastic, the manufacturer’s designation – because “nylon” is a family and the differences between grades are larger than the differences between metals.
- Minimum wall thickness, and any feature that has to be clamped identified. These are design requirements on a plastic part and they do not exist on a metal one.
- Tolerance scheme, differentiated – and on a plastic part, a note that a conditioning period precedes measurement, because that is what makes the measurement meaningful.
- Thread form, specified for the material rather than copied from a metal part.
- Where the part is clamped, and how, on a plastic part especially.
- Any fit – press, interference, or snap – and whether it is intended to be permanent, with the long-term behaviour of a plastic fit stated.
- Surface finish requirement expressed as a machined finish on a plastic part, and as a coating specification on a metal part.
- Material’s environment and medium, so the alloy or the grade is matched to it, with mill certificates on a metal part.
Could this part be moulded rather than machined?
Direct answer: On a small precision part the answer is very often yes, and a moulded plastic part is faster, cheaper, and more repeatable than a machined one – and it can have features a machining process cannot produce economically, like internal threads, snap fits, and thin-walled hollow sections. Machining wins where the volume is low, where the material has to be metal, where the part has to be machined from a specific stock, or where the geometry is genuinely three-dimensional and moulding would need a multi-cavity tool with a prohibitively long cycle. On a plastic part the question is worth asking early, because a machined plastic part is often a design that has been machined when it should have been moulded, and the difference in cost and in achievable geometry is large.
Why is plastic versus metal a materials question rather than a process question?
Direct answer: Because the two families behave so differently in machining that the choice changes the design rather than the parameters. Metal conducts heat away and stays dimensionally stable; plastic heats locally, softens and expands, so it is measured differently after a heavy cut. Wall thickness, thread form and even which features can exist all change – the same geometry in acetal and in stainless steel is two different parts.
Which plastic is the default for a small precision machined part?
Direct answer: Acetal, usually POM or POM-C. It machines beautifully, gives a good surface finish, has low friction, good dimensional stability and low shrinkage, so it is the machinist’s plastic and the default for a small precision part. The grade is the specification – ‘nylon’ names a family, and the differences between grades are larger than the differences between metals.
CNC Machining Parts is the range this part sits under; the overview page pulls together the tooling logic, finishing options and tolerance notes that apply across the family.
Specifications
| Item | Custom CNC Machined Plastic and Metal Parts |
|---|---|
| Brand | AUNOV |
| Designing | Your drawing sets the part – unusual walls, threads or tolerances are feasibility-checked first; the approved drawing is kept as the controlled master. |
| Tooling | Tooling is built and held under your part number, so a die can be re-cut against the approved drawing, and maintenance is tracked against the part number. |
| Samples | Sample parts are measured and reported before submission, so any deviation is corrected at sample stage. |
| Materials | Standard stock: carbon steel (SPCC / DC01), 304 / 316 stainless steel, aluminium, brass; mill certificates and heat numbers accompany the first article. |
| Surface finish | Finish selected from the drawing: plating, coating, anodising or passivation; alternatives quoted with the quotation, samples approved in writing. |
| Processing | CNC turning from bar or billet, concentricity held across operations; every stage is logged against your part number. |
| Equipment | 12 CNC turning centres with automatic bar feeders, with in-house toolmaking to keep dies and fixtures maintained. |
| Tolerance | +/-0.02 mm general machining, tighter on flagged dimensions; dimensional reports accompany the first article. |
| Delivery terms | CIF or DDP, with FOB available, T/T or L/C, with D/P accepted on repeat business; call-off schedules are supported. |
Related Products
Request a Quote for This Part
Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).




