
A precision cup is defined by which of its four dimensions is tight, and choosing wrong wastes the part
A precision drawn cup in stainless steel or aluminium looks like a straightforward deep draw, and it is specified with a tolerance structure that says flange and rim dimensions at +/-0.05 mm with the wall controlled by the draw. That structure is correct, and it is also incomplete in a way that matters: a cup has four dimensions that can each be made tight, and the design has to know which one the application actually depends on. Making the wrong one tight costs money and achieves nothing, and the review’s job is to find out which one it is before the tooling.
We draw these progressively through several stages, annealed between draws, then trim and pierce, and batch records are filed so a repeat order starts from approved data, on a press shop running 5-250 T mechanical and 250-500 T hydraulic presses with annealing ovens on site, CNC turning centres for secondary operations, and CMM inspection. Flange and rim dimensions to +/-0.05 mm with the wall controlled by the draw, and dimensional reports accompany the first article. Carbon steel, 304 and 316 stainless steel, aluminium and brass are all held in stock, with material substitutes proposed only with your written approval. Natural, plated or coated per the print, with the agreed finish logged and alternatives quoted alongside. This page is about the four dimensions and about how the choice between them changes the part.
The four dimensions, and what each one costs to control
- The diameter. Set by the punch, so its accuracy is a tooling dimension rather than a process one. A punch-made diameter is consistent between parts and drifts slowly with tool wear. Tightening it costs a more accurate punch and a tighter incoming material specification. This is the cheapest of the four to make tight.
- The depth or height. Set by the draw’s depth and by the material’s springback, so it is affected by the material’s incoming condition and by the tool’s wear. It is more variable than the diameter and more expensive to control, and on a multi-stage draw the depth accumulates every stage’s variation.
- The wall thickness. Inherited from the incoming material and modified by the draw. Tightening it means buying material to a thickness specification – a purchasing decision with a cost and a lead time, and not something the press can achieve. On a cup where the wall is functional this is the cheapest tight dimension and the easiest to forget.
- The flange or rim’s flatness and position. This is the one that usually has to be machined rather than drawn, and it is the most expensive to control because it needs a secondary operation. Where the flange seals or locates, this is the dimension that matters and it is the one that cannot be made tight by a better die.
So the four dimensions have genuinely different economics, and the design’s job is to say which one the application needs. A cup that locates a sensor needs the bore tight. A cup that seals needs the flange flat. A cup that holds a volume needs the diameter and the depth. A cup that carries pressure needs the wall. A drawing that tightens all four is a drawing that pays for four secondary operations and gets no benefit from three of them.
The bore, which is the one that catches people out
Where a cup has to locate or seal around something that goes inside it, the bore becomes the controlling dimension, and a drawn bore cannot serve. Four specific reasons, and they are worth stating because the failure is gradual rather than obvious:
- A drawn bore is tapered. The wall thins during the draw, and the bore’s diameter changes along its depth. A tapered bore gives a loose fit at the top and a tight one at the bottom, or the reverse, and a locating element in it will sit at an angle.
- A drawn bore’s roundness is only as good as the punch’s, and a bore that is in size but out of round will locate an element unevenly.
- A drawn bore’s surface is work-hardened and carries draw marks, which is a poor surface for a seal and a poor bearing surface.
- A drawn bore’s size drifts with punch wear, slowly and predictably, which on a tight band means a tool maintenance interval rather than a quality problem.
The standard answer is a machined bore – reamed, honed, or bored and finished in a secondary operation – and this is why the tolerance structure on a cup with a functional bore always shows a tight band that the drawing attributes to machining rather than to forming. It is also worth asking, on a cup with a drawn bore, whether the bore genuinely has to be tight or whether a clearance fit with a compliant element would work – because that question, asked at review, can remove a secondary operation entirely.
Multi-stage drawing, and where the depth error comes from
Progressive drawing through several stages with annealing between them is the route, and on a precision cup it has two specific consequences:
- The depth accumulates. Each stage’s draw contributes a small depth variation, and on a three-stage cup the total depth variation is roughly the sum of the three. Where the depth is a functional dimension, this is the reason it cannot be held to a tight band by a better tool alone – and the reason a machined base or a machined depth feature is sometimes needed.
- The anneal is a distortion event. Each interstage anneal heats the part and lets it cool, and it moves. The anneal’s cycle has to be a controlled process parameter rather than a furnace setting, and on a part whose depth is tight this is a real consideration. Where the material’s condition matters, the material’s specification is part of the tolerance scheme.
Material, and the two that are usually chosen
Carbon steel, 304 and 316 stainless steel, aluminium and brass are all held in stock. On a precision cup:
- 304 stainless steel is the default where the cup carries food, is cleaned, or is in a mildly damp environment. It draws well, it takes a fine surface, and it is dimensionally stable.
- 316 stainless steel where chlorides, salt, or acidic content are present – which includes many food and beverage applications and all saline ones.
- Aluminium where weight matters or where a specific surface is needed, and 3003 or 1050 for the deepest draws. Aluminium is the most formable of the group, which means a deeper cup is achievable, and its springback is lower so a formed feature holds its angle better.
- Carbon steel where cost governs and the environment is dry. It will need coating, and the coating changes the flange’s dimension.
- Brass where a warm appearance, a specific corrosion behaviour, or a machinability requirement applies.
Finishing, and which dimension the finish attacks
Natural, plated or coated per the print, with the agreed finish logged and alternatives quoted alongside, and samples approved in writing. On a precision cup, the finishing question is which of the four dimensions the coating changes:
- The flange’s thickness grows, by roughly twice the coating thickness, which on a flange at +/-0.05 mm is a real fraction of the band. If the flange seats against something, this has to be stated as a pre- or post-coating dimension.
- The diameter grows, by the same amount in one axis and the same amount in the other, so a clearance fit can close and a press fit can open.
- The bore shrinks, by twice the coating thickness, and a bore that is a locating fit must be masked or specified post-plate.
- Passivation on stainless steel changes nothing dimensionally, which is why it is the safest choice on a cup whose dimensions are tight and whose appearance requirement is modest.
That one sentence usually settles the design
Eight things, and the first is the one that saves the most money on this part type:
- Which of the four dimensions is actually critical, stated as a requirement. This is the single most valuable thing on a precision cup drawing, because it determines the entire tolerance scheme and which secondary operations are needed.
- Which features are drawn and which are machined, stated explicitly, so the tolerance bands are attributed correctly.
- Flange and rim dimensions at the stated band, with flatness as a separate callout from size, and whether they are machined.
- Bore tolerance and roundness, separately, wherever the bore locates or seals.
- Wall thickness held to print, with the minimum location – the punch nose in the base – and an acknowledgement that this is a material specification.
- Material grade and temper, confirmed in writing, and where the depth is tight, the incoming specification that supports it.
- Any interstage anneal, and whether its dimensional effect needs accounting for.
- Which surfaces are masked, and whether dimensions apply before or after finish.
What is going in this cup, and what does it need?
What is going in this cup, and what does it need from the cup? That sentence usually answers the tolerance question on its own. A cup that holds a liquid needs to be cleanable and leak-tight and nothing more precise. A cup that locates a sensor needs a tight bore. A cup that carries pressure needs a wall calculated and a base reinforced. A cup that is part of a customer’s assembly needs a flange flat and a depth consistent. The designs that go wrong on this part type are the ones where nobody asked, so the part met every requirement on the drawing and did not do the job – and the ones that cost the most are the ones where the design tightened all four dimensions when the application needed one.
If you are weighing drawing against machining or welding for this geometry, the guide to deep drawn covers sets out where each route wins; the full Precision Deep Drawn Parts range is linked from the overview page.
Specifications
| Item | Custom Precision Deep Drawn Cup Stainless Steel Aluminum Stamping Deep |
|---|---|
| Brand | AUNOV |
| Designing | Your drawing sets the part – a manufacturability review comes back with the quotation; the same drawing is used for every repeat order. |
| Tooling | Dies, fixtures and gauges are made in our own toolroom, so no tooling step is outsourced, and ownership is confirmed on the quotation. |
| Samples | Approval is in writing, and the signed sample is kept as the reference for repeats. |
| Materials | Carbon steel, 304 / 316 stainless steel, aluminium and brass are all held in stock; material substitutes are proposed only with your written approval. |
| Surface finish | Natural, plated or coated – the print decides, and the agreed finish is logged; alternatives quoted with the quotation, samples approved in writing. |
| Processing | Progressive drawing through several stages, annealed between draws, then trim and pierce; batch records are filed so a repeat order starts from approved data. |
| Equipment | Press shop running 5-250 T mechanical and 250-500 T hydraulic presses, annealing ovens on site, with CNC turning centres for secondary operations and CMM inspection. |
| Tolerance | +/-0.05 mm on flange and rim dimensions, wall controlled by the draw; dimensional reports accompany the first article. |
| Delivery terms | FOB Ningbo or Shanghai, T/T or L/C, with D/P accepted on repeat business; each volume tier carries its own quoted price. |
Frequently Asked Questions
What defines a precision drawn cup: which dimension is tight?
A cup has four dimensions that can each be made tight – flange, rim, wall and bore – and the design must know which the application depends on. Making the wrong one tight costs money and achieves nothing.
Which of the four dimensions catches people out?
The bore. It is often specified tight but is the hardest to hold through a draw, so it is drawn to an intermediate band and then sized or reamed on a turning operation to land the feature.
Which materials are usually chosen for a precision cup?
304 or 316 stainless steel and aluminium are the usual choices, with material substitutes proposed only with written approval. Flange and rim are held to +/-0.05 mm with the wall controlled by the draw.
How is a precision cup finished and verified?
The finish attacks a specific dimension – anodise grows the ID, plating adds to the OD – so the affected feature is sized for the finished state; dimensional reports accompany the first article. Minimum order 1,000 pieces, 24-hour quote.
Related Products
Request a Quote for This Part
Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).




