Deep Drawing vs Metal Spinning: Which Process Fits Your Part
Deep drawing and metal spinning both turn a flat disc of sheet metal into a hollow shape, but they move the metal in completely different ways. In deep drawing a punch pulls the whole blank through a die while a blank holder controls the flange, so the sheet flows plastically across the entire part in one stroke. In spinning the disc is clamped to a rotating mandrel and a roller works a small contact patch, progressively pushing the metal onto the form. If your part is a deep, closed-end shell that has to repeat dimension after dimension, draw it. If it is a large, shallow, axisymmetric cone, dome or reflector in a modest quantity, spinning is usually the shorter route to a finished part. The confusion is understandable: both start from a round blank and both produce a seamless shell, and a drawn part is often trimmed on a lathe afterwards.
We run drawn parts on 5–500 ton presses to 150 mm depth in 0.15–3.0 mm sheet, holding ±0.05 mm on a normal tool and ±0.02 mm on ironed walls. Those figures come off our own tooling. We also quote spun and light-fabricated parts, but we do not publish a tolerance table for spinning, because we have not measured one to the same standard across our own line. This page is about choosing between the two before anyone cuts a tool.
The split is how the metal moves
A draw is a whole-blank event. The flange has to be free to feed inward while being held flat, and the wall that forms is the result of that flow. Every section of the blank is straining at the same time, which is why draw beads, blank shape and blank-holder force are designed together, and why a non-symmetric shell needs a different bead height at each corner. The metal thins where it stretches and thickens slightly at the rim; the wall is a gradient, not a single number.
Spinning is local. The roller contacts a narrow band, that band yields, and the rest of the blank is still elastic. Pass after pass walks the metal down onto the mandrel. Because only a small volume is plastic at any instant, the forces are far lower and the tooling can be a shaped mandrel plus a roller rather than a matched punch-and-die set. The trade is time: the shape is built up over many revolutions rather than one press stroke.
That one distinction explains almost every downstream difference. Tooling cost, cycle time, achievable wall, surface finish and the kind of geometry that behaves all follow from whole-blank flow versus local flow.
Deep drawing vs metal spinning at a glance
| Aspect | Deep drawing | Metal spinning |
|---|---|---|
| Material flow | Whole flange flows plastically in one stroke | Local contact patch formed progressively over many revolutions |
| Tooling | Matched punch, die, blank holder, draw beads, plus redraw and ironing stations | Mandrel and roller; CNC lathe or manual spinning lathe |
| Best geometry | Deep cups, cans, sensor sleeves, closed-end enclosures, rectangular shells | Axisymmetric cones, domes, hemispheres, reflectors, flared rims, large shallow covers |
| Non-axisymmetric parts | Possible with a staged route and section-by-section bead design | Generally unsuitable; rotation is the process |
| Wall thickness | 0.15–3.0 mm on our presses, with roughly 10% thinning per stage to defend | Conventional spinning keeps close to the starting gauge; shear spinning deliberately reduces it |
| Depth we quote | Up to 150 mm, often over several redraws | Better suited to wide, shallow profiles than to tall thin walls |
| Repeatability | Once the tool is proven, each stroke reproduces the same shell; ±0.05 mm ID typical | Depends on the pass schedule and operator or program; finish and gauge vary more run to run |
| Surface | Die finish, with possible draw lines and scoring to control | Visible spiral tool marks unless polished out |
| Economics | Higher tool cost, low unit cost, strong from 1,000 pieces upward | Low tool cost, higher labour time per part, attractive for prototypes and short runs |
Where spinning is the shorter route
Spinning wins on a part that is round, wide and not very deep. A lamp reflector, a spun aluminium cover, a flared funnel or a domed end cap can be made from a simple mandrel in a day or two, with no draw die to design. For a design that is still moving — three diameter options, two rim angles, a customer who may change the profile next month — that is a real advantage. Change the mandrel or the program and the next part is different.
Size works in spinning’s favour too. A mandrel for a 600 mm reflector is a manageable piece of tooling; a matched draw die for the same diameter is not. The process also handles a profile that would be awkward to release from a rigid punch, because the mandrel can be segmented or the part can be spun over a form and then trimmed.
The limits are just as clear. Rotation is the process, so an oval, square or off-axis shell is not a spinning job; our guide to irregular deep drawn parts covers what happens when every section wants a different draw ratio. Holes, slots and vents are also a problem: a spun blank has no station to pierce them, so they become a secondary operation, and a hole near the rim changes how the metal feeds. We have a spun parts family on the site for exactly these shallow, symmetric components, and the covers guide explains when we move a cover from spinning to drawing as the wall gets taller.
Where deep drawing earns its tooling
Once the wall has real depth and the part has to repeat, drawing takes over. A closed-end shell that must hold a seal, a sensor sleeve with a controlled bore, a battery can with a uniform wall, or a pressure cup with a thickness the designer actually relies on: these are drawn parts. The die is expensive, but the stroke is fast and the dimension is set by steel rather than by a pass schedule.
The limiting draw ratio is the first hard constraint. On our presses we use 2.1–2.2 for DC04, 1.85–2.05 for 304 stainless steel and 1.80–1.95 for 5052 aluminium. Past the ceiling the shell splits at the punch radius, so we add a redraw, and when work hardening exhausts the ductility we put an anneal between stages. The LDR reference gives that planning data with the test conditions behind it, and the sixteen process routes shows where the stages go.
Ironing is the other thing drawing can do that spinning cannot. An ironing pass squeezes the wall through a controlled gap, straightening it and bringing the thickness to a specifiable number. The 304 pressure cup case is a worked example: a 120 mm deep shell drawn from 1.0 mm sheet and ironed to 0.78 mm, holding ±0.02 mm on the wall. If your print calls out a wall thickness rather than just a starting gauge, that is the comparison to read next — our ironing vs redraw page separates the two passes.
What happens to the wall in each process
In a draw the wall is a consequence of flow. It thins near the punch radius, thickens towards the flange and, on anisotropic sheet, comes out with a wavy rim called earing that has to be trimmed. We hold thinning to about 10% per stage on production parts and measure the wall on the first article rather than assuming it.
Conventional spinning is close to constant gauge because the roller is mostly bending the blank onto the form rather than stretching it. Shear spinning, sometimes called shear forming, is different on purpose: the roller presses the blank against the mandrel with a controlled gap, and the wall ends up thinner by the sine of the cone half-angle. That is a genuine reduction, and it is the one spinning variant that competes with ironing on wall control. ASM Handbook Volume 14B treats spinning and deep drawing in the same volume for exactly this reason — both are sheet-forming routes with a thickness budget to manage.
Either way, ask for a wall map with the first article. If a supplier quotes a single wall thickness for a deep drawn part, ask where on the shell it was measured.
What we do not claim
We do not publish spinning tolerances, cycle times or thinning percentages measured on our own presses, because we have not run that measurement programme. The spinning column in the table above is process behaviour, not a specification we will put on a drawing. If a spun part needs a guaranteed dimension, we agree the inspection method before quoting it.
We do not claim deep drawing is always cheaper at volume, or that spinning is only for prototypes. A well-programmed CNC spinning cell can be the right production route for a large shallow dome, and a low-volume deep shell can still justify a draw die if no other process will hold the wall. We also do not publish leak-rate or autoclave-cycle figures for either route; we have not tested them to a published standard on our line.
We do not say ±0.02 mm is a general drawing tolerance. It needs an ironing pass and guided tooling, and a wide shallow cover will not hold it. And we do not claim 6xxx aluminium can be deep drawn like 5xxx; those grades are for shallow forming with T6 applied afterwards, which the material selection guide sets out grade by grade.
Sources behind this comparison
The process definitions and the thickness behaviour above sit inside a body of work maintained outside our shop.
- ASM Handbook, Volume 14B: Metalworking — Sheet Forming — separate articles on deep drawing, spinning and springback, plus formability testing.
- ASTM A240/A240M — the specification the 304 and 316 stainless steel sheet we draw is supplied against.
- Wikipedia: Metal spinning — background on conventional spinning, shear forming and the mandrel-and-roller setup.
- DIN 8584 — the German classification of forming operations that places drawing and spinning in different subgroups.
- ISO 9001 — the quality management standard our inspection and first-article records sit under.
How to send us the choice
Put the profile, the diameter and depth, the starting gauge, the material, the annual volume and any dimension that is functional on the drawing. Tell us which surfaces have to seal and where the wall thickness is measured. We will say which route we would tool, and if a spun part is the better answer we will say that before anyone pays for a draw die. Tooling is made in house, quotes come back within 24 hours, and the minimum run on new tooling is 1,000 pieces.
Frequently asked questions
When is metal spinning a better choice than deep drawing for a round part?
Spinning is usually better when the part is axisymmetric, wide relative to its depth, needed in a small quantity, or still changing shape. A shallow cone, dome or reflector needs only a mandrel and a roller, so there is no matched die to pay for or revise. Once the wall gets tall, the volume rises past roughly 1,000 pieces, or the bore has to repeat within a few hundredths of a millimetre, the draw die earns its cost back.
Does spinning thin the wall of a metal part?
Conventional spinning keeps the sheet close to its starting gauge, because the roller is mainly bending the blank onto the mandrel. Shear spinning is the exception: the roller works a controlled gap and the wall is deliberately reduced, by an amount tied to the cone half-angle. Deep drawing thins the wall as a side effect of stretch, which is why we budget roughly 10% per stage and measure the finished wall rather than quoting the incoming gauge.
Is a spun reflector watertight, or does it need a sealed joint?
A spun reflector is watertight as long as the profile is one continuous piece of metal with a closed end and no pierced holes. Spinning does not create a seam. The practical risks are local thinning from an aggressive pass schedule and any hole added afterwards, which needs its own sealing step. A deep drawn shell reaches the same result with a more repeatable wall, which is why sealed enclosures with a pressure or sensor duty are normally drawn.
At what sheet gauge does a draw die beat a spinning mandrel?
We draw sheet from 0.15 to 3.0 mm on our own presses. The lower end needs careful blank-holder control because a thin flange wrinkles easily, and the upper end needs press tonnage and larger die radii. Spinning is often more comfortable on thicker, wider discs, but it gives you less control over the finished gauge. The right question is usually not the gauge but whether the print calls out a final wall thickness that has to be held.
Why is a matched punch and die set dearer than a mandrel and roller?
A draw tool is a system: punch, die, blank holder, draw beads, and often redraw and ironing stations, all designed together so the flange feeds without tearing or wrinkling. A spinning setup is a mandrel and a roller, sometimes with a CNC program. The draw die costs more up front and then produces a part per stroke with a dimension set by the steel; the spinning setup costs less up front and spends more labour time on every part.
Would we ever flange a drawn shell on a spinning lathe?
Occasionally, but not as one process. A shell may be deep drawn for its wall and then have a rim flared, rolled or sized on a lathe, which is a spinning-like finishing operation. What we avoid is planning a part that needs a drawn wall and a spun profile without deciding where the handover happens, because the wall thickness at that boundary will not be what either process assumes on its own.
Key point: Deep drawing suits repeatable high-volume shells with tight tolerances; spinning suits low-volume, large or axisymmetric shapes.
Last reviewed: 2026-11-05 · Reviewed by Sam Zhang, Process Engineer
