Aluminum CNC Machined Motor End Caps

Brass Hex Bushings and Nut Fittings Assortment
Brass Hex Bushings and Nut Fittings Assortment

An aluminium motor end cap is a shallow cover with a bore in it, and there are only three things that can go wrong with it: it can be out of flat, it can be out of true, or it can be in the way of the thing it covers. The first is a machining problem, the second is a concentricity problem, and the third is the one that decides the design – and it is not visible on a dimensioned drawing at all.

Which is why on this part the interesting engineering is the clearance budget, not the tolerance.

What the cap actually does

An end cap on a motor or a gearmotor closes the end of the housing. It has three or four jobs and they compete.

  • It closes the housing. Depending on the design that is a bearing seat, a shaft seal, or a dust and water barrier. Where it is a bearing seat or a seal seat, the cap is a precision functional surface and most of the design follows from that.
  • It locates something. A pilot spigot, a register, or a bolt pattern that sets the cap’s position relative to the housing. If the cap is located by a spigot, the spigot is the part that has to be accurate and the bolt pattern is only clamping.
  • It takes the load from any fasteners. Bolt holes in a thin aluminium cap with a raised boss are the standard arrangement, and the boss is there because a fastener bearing on a thin cap will dimple it.
  • It has to get out of the way. This is the third job and the one that decides the drawing’s dimensions: the rotating or moving part must clear the cap, and the clearance is usually the tightest dimension on the assembly even though it appears on the housing’s drawing and not the cap’s.

The clearance budget, which is the real specification

On an end cap there is a chain of clearances and thermal growths between the rotating part and whatever it must not touch, and it is worth laying the chain out because it is the part that causes the field problems.

  1. Axial clearance between the rotating part and the cap’s inner face, at room temperature and at the maximum operating temperature.
  2. Radial clearance between any shaft, key, or boss and the cap’s bore. This is where an aluminium cap is at a disadvantage: aluminium’s expansion coefficient is roughly twice steel’s, so on a shaft-through-cap arrangement the clearance closes faster than it would on a steel cap.
  3. The assembly’s accumulated tolerance stack, which includes the housing’s bore, the cap’s bore or spigot, the fasteners’ clearance, and the cap’s flatness. This stack is where a cap that is individually correct still does not assemble, and it is why the cap’s own tolerances cannot be chosen in isolation from the housing’s.
  4. Thermal growth of everything, including the housing if it is steel and the cap if it is aluminium. A steel housing with an aluminium cap and an aluminium or steel shaft produces a stack that changes with temperature in three directions at once.
  5. Deflection. An end cap is usually the least stiff part in the chain, because it is a thin disc cantilevered from its bolt holes. Under load – a shaft’s side load, a bearing’s preload – the cap deflects, and its deflection at the bore is not in the axial budget even though it is in the real one. This is the item most often missed, because it is a structural deflection rather than a dimensional clearance.

The point worth making on this part is that the cap’s dimensions cannot be specified correctly in isolation. They have to be specified against the housing’s dimensions and the shaft’s, and the assembly length and the clearance have to be coordinated with whoever owns those parts. A cap drawing that is dimensioned correctly on its own can be impossible to assemble.

The bore, and the difference between a clearance bore and a register

On an end cap the central bore is the feature that does the work, and there are two versions of it that look the same on a drawing and are completely different.

  • A clearance or bearing-seat bore. The cap surrounds a bearing or a shaft and its job is to hold the bearing’s outer ring or to clear the shaft. Requirements: diameter and roundness, concentricity to the cap’s mounting face and to its bolt pattern, and a surface finish the bearing’s seat requires. Where the bore is a bearing seat, its size and its fit to the bearing are the whole requirement and the tolerance is tight.
  • A locating register or spigot. The cap is located by a pilot that enters a bore in the housing, and the pilot is what sets the cap’s position. Requirements: the pilot’s diameter and roundness, the pilot’s length, the pilot’s concentricity to the cap’s outer features, and the pilot’s fit. The bolt holes are then only clamping, and their position tolerance is relaxed.

Which one it is decides the tolerance scheme completely. It is worth stating on the drawing, and it is worth checking which parts of the cap’s dimensions are actually functional as a result.

One more item specific to an aluminium cap: the bore’s burr and its edge. A machined bore in aluminium leaves a burr at the exit, and where the cap is over a bearing or a shaft that burr is a snag and a noise source. It is a small item and it is a real one.

Flatness, and why it is worse on an aluminium cap

An end cap is a disc, and a thin disc in aluminium is the classic distortion case for three separate reasons, and they all point the same way – the part will not be flat and the cause is the material and the machining.

  1. Residual stress and single-sided material removal. A cap that is machined from one side has had stress removed from one side, and it will bow. This is the same mechanism as on the plate and housing pages, and on a thin disc it is more pronounced because the section is thin.
  2. Clamping distortion during the finishing operation. A thin disc clamped on a vacuum fixture or on a chuck will be held in a shape that is not its natural shape, and the face will be cut to that shape. After it is released it relaxes. On a thin aluminium disc this is the dominant effect and the practical responses are to support the centre as well as the edge, to use a fixturing strategy that does not distort the part, or to machine the face in a way that is not sensitive to it.
  3. Thermal, in service. A cap that is bolted to a housing and sits near a heat source will bow away from its housing as it heats, and a bowed cap means the bolt faces lose contact at the outer diameter, which reduces the clamp and which changes the axial clearance. On a thin aluminium cap this is a real and measurable effect and it is worth specifying a flatness with the mounting condition stated.

So: flatness should be specified with the support or mounting condition stated, because a cap’s flatness supported at its centre and unsupported at its edge are different numbers, and measuring it in the wrong condition produces a meaningless result.

A thin end cap is decided by three things, none of them formability

1050, 3003, 5052 and 6061 at 0.5 to 3.0 mm stock, with temper matched to the route. On an end cap the alloy choice is dominated by three things, all of them related to the fact that this is a thin disc.

  • Formability is not the driver here because the cap is machined rather than formed. So the choice is about machining and stiffness, not about how the blank was made.
  • Strength at a thin section. On a thin cap, the alloy’s yield strength is what resists the fastener’s bearing stress at the bolt bosses and the cap’s deflection under load. 6061 is the general answer and 5052 is the answer where a lower yield is acceptable and better corrosion resistance is wanted.
  • Fatigue, if the cap is on a rotating assembly. Aluminium has a lower fatigue strength than steel and it will not tolerate a cyclic load the way a steel cap would. On a cap that is in a vibrating application, this is a design limit rather than a detail.
  • Corrosion, and the galvanic coupling that this part is prone to. An aluminium cap bolted with steel fasteners is a galvanic couple at every bolt hole, and the crevice at the bolt hole is exactly where water collects. This is one of the most common practical corrosion mechanisms on an aluminium end cap and it argues for a plating, an anodise with the holes considered, or stainless steel fasteners.

A bearing seat bore is almost always masked

Surface treatment matched to the duty – plating, coating or polishing – with the agreed finish travelling with the part number. Three specific items on this part.

  • The bore, if it is a bearing seat, is almost always masked. A plated or anodised bearing seat changes the bearing’s fit, changes its surface, and changes the interference fit that a rotating bearing seat usually relies on.
  • The spigot, if it locates the cap, is usually specified with the coating in mind, because the spigot’s fit is what locates the cap and a coating changes it by roughly twice its thickness on the diameter.
  • The mounting face is where the finish is usually wanted, and here it matters that an anodised or coated face is not flat in the way a bare face is – it has a slightly different texture and a slightly different thickness distribution. For a bolted face this is not a problem; for a spigot-located face it is.
  • Anodising and the bolt holes – anodising closes the clearance holes, which is generally beneficial, and it changes the boss’s bearing surface, which is generally not wanted. The masking list has to name the bosses.

Tolerance, and what to flag

+/-0.01 mm on ground diameters, GD&T from the print, finer bands confirmed from capability data. On an end cap the flagged dimensions are the bore, the concentricity, the flatness and the axial position.

  • The bore’s diameter and roundness, to the bearing’s or the shaft’s fit, with the fit stated as a fit.
  • Concentricity of the bore to the mounting face, and to the bolt pattern or the spigot. On an end cap this is the tolerance that keeps the bearing seated correctly and it is normally the one that should be tightest.
  • Flatness of the mounting face, with the mounting condition stated.
  • The axial position of the bore’s shoulder, the spigot’s end, or the cap’s face, to whichever is the assembly’s datum. On a cap the axial dimensions are a stack and one of them has to be the reference.
  • Perpendicularity of the bore’s axis to the mounting face, where the bore’s alignment matters to the housing rather than to the bearing.
  • The bolt pattern’s position to the bore and to the mounting face, so the pattern’s relationship to the bore is held rather than each to the machine’s origin.
  • Overall dimensions and thickness at a general band, except where the thickness affects the deflection, in which case it is a structural dimension and should be held.

Bore roundness and concentricity to the mounting face travel together

  1. The bore’s diameter, roundness and concentricity to the mounting face, measured and reported together, on the CMM. This is the group of measurements that determines whether the cap is fit for its purpose.
  2. Flatness of the mounting face in the stated mounting condition.
  3. Burr and edge condition at the bore’s exit and at any hole, verified visually against an agreed standard.
  4. A functional fit check into the housing or onto a master, on a sample. On an end cap this tests the whole stack and it is the most informative inspection available.
  5. Finishing thickness and adhesion on the first article, with the bore and any spigot verified as masked or as coated to specification.
  6. Batch records filed so a repeat order starts from approved data, which on a cap in a series of matched parts is worth the paperwork because the parts are usually used in sets.

Pilot-located, or bolted only, and the running clearance

Is the cap located by a pilot or only bolted? And what is the running clearance between the shaft and the cap at the highest operating temperature? The first question decides the entire tolerance scheme – a pilot-located cap needs a tight roundness and concentricity on the pilot and can relax the bolt pattern, while a bolt-only cap needs a tight bolt pattern and a face flatness and has no pilot accuracy at all. The second question is the one that decides whether the cap works, because an aluminium cap on a steel housing closes its radial clearance roughly twice as fast as a steel cap would, and a cap that is dimensionally correct at room temperature can interfere at temperature. Together they are the two numbers that a cap actually needs, and they are the two that are most often absent from the enquiry. Supplying them costs two lines and it converts a cap from a cover into an engineered part.

Our CNC Machining Parts range is where this part sits. The cnc machining parts pages carry the process notes, common materials and inspection points behind every product in the family.

Specifications

Frequently Asked Questions

A thin end cap’s closure and its fit live in one number – what is it?

Direct answer: It closes the bore and locates the end. The cap is the closure, and its real specification is the clearance budget – the gap between the cap and the bore it closes. A cap that is too tight jams; too loose and it does not locate. The clearance is the design, not an afterthought.

The gap a cap’s bore leaves is either clearance or register – how are the two specified apart?

Direct answer: A clearance bore just lets something pass, so it is loose; a register locates something, so it is a controlled fit. Mixing the two is the most common error on an end cap – a bore specified as clearance and then asked to locate. The drawing has to say which the bore is, because the tolerance is completely different.

An aluminium cap bows where a steel one would not – what causes the extra bow?

Direct answer: Because aluminium is soft and moves under machining and under clamping. A thin aluminium cap bows more than a steel one for the same load, and its flatness is harder to hold. The cap’s flatness is therefore a design consideration in aluminium that a steel cap does not have.

ItemAluminum CNC Machined Motor End Caps
BrandAUNOV
DesigningDriven by your drawing or a physical sample – samples are reverse-measured into a controlled drawing; the same drawing is used for every repeat order.
ToolingTooling is built and held under your part number, so die cost stays transparent, and first-article timing is measured from the tooling start date.
SamplesSample and first article are the same discipline here: measured, reported, then approved.
Materials1050 / 3003 / 5052 / 6061 aluminium, 0.5-3.0 mm stock – temper matched to the forming depth or machining route of this cap.
Surface finishSurface treatment matched to the duty: plating, coating or polishing; the agreed finish travels with the part number.
ProcessingBar-fed turning with milled features completed in the same clamping; batch records are filed so a repeat order starts from approved data.
EquipmentCNC turning centres with bar feeders and 3-/4-axis machining centres, backed by CNC turning centres and a climate-controlled inspection room.
Tolerance+/-0.01 mm on ground diameters, with GD&T taken from your print; finer bands confirmed from capability data before quoting.
Delivery termsFOB, with DDP offered for EU and US addresses, T/T with deposit and L/C for larger runs; price breaks tie to annual volume.

Request a Quote for This Part

Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).