
A cup is often a bearing seat, a guide, or a socket
The deep drawn cup – a closed-end cylinder used as a housing, a bearing seat, a guide, or a socket – is a shape so common that it is easy to treat as a commodity and specify too loosely. In practice, a drawn cup’s value is in its internal surfaces: the inside diameter that receives a bearing, the bore that guides a plunger, or the socket that holds a component. Get those right, and the cup is an excellent replacement for a machined or cast housing at a fraction of the cost; get them wrong, and the assembly binds or rattles.
We draw cups from 0.4-3.0 mm steel, stainless steel, and aluminium, in diameters from a few millimetres to a few hundred, and this page is about the cup as a precision interface rather than purely as a container.
Three dimensions define a functional cup
Almost every functional cup is judged on three things, and a specification that omits any of them invites an argument later:
- Inside diameter – the fit that receives a bearing, a shaft, or a plug. Here the tolerance is an engineering fit (H7, a press-fit band, or a clearance band), not a nominal with a plus-or-minus.
- Straightness of the wall – a cup wall that barrels or tapers will not present a uniform fit along the engagement length; a deep cup with a tapered bore either seizes a bearing or lets it rock.
- Base thickness and concentricity to the bore – the base often carries an axial load or seats against a face, so its thickness and its perpendicularity to the axis matter.
Outer diameter is usually less critical unless the cup presses into something itself, in which case the OD and the wall thickness together set the press fit and the hoop strength.
Cup as a bearing seat
A very common use is a cup that houses a small bearing – a ball bearing, a sintered bushing, or a plain sleeve. The requirements:
- Bore roundness and straightness – a pressed bearing follows the bore it is pressed into, so an oval or tapered bore gives a distorted bearing race and a noisy, short-lived result.
- Bore finish – a rough bore frets the bearing outer ring; a finish around Ra 0.8-1.6 µm is a normal target for a pressed-in bearing seat.
- Bearing retention – either an interference fit or a formed in-ward lip/staking that traps the bearing. We can form the retention shoulder in-die so a separate circlip is unnecessary.
Cup as a guide or a cylinder bore
Where the cup guides a plunger, a piston, or a sliding rod, the fit is a running clearance and the bore must be both round and straight over the stroke. Deep drawing a straight bore is harder than it looks once the depth exceeds about twice the diameter, because the material thins and the bore can barrel. Our approach:
- Keep the drawn depth within the single-stroke limit where possible, and use a redraw with a guided punch for deeper cups.
- Where a tight straight bore is functional, add a sizing or a light boring step on the critical length rather than pretending the draw can hold it.
- Specify the surface finish for the sliding interface – too rough abrades the seal or the rod, too smooth can starve the lubricant film.
Wall thickness, base thickness, and the load path
A cup carries load through two paths: the base (axial) and the wall (radial/hoop and bending). Drawn cups thin from base to rim, and the base usually stays close to the blank thickness. That is convenient for a bearing seat, where the bore is the functional surface and the base carries thrust. Where the cup presses into a housing and must resist hoop stress, the wall thickness at the engagement zone is what matters, and we check it against the interference and the housing stiffness rather than assuming the nominal.
Materials and finish
| Mild steel / DC01 | Cheap, easy to draw, good for painted or plated cups; needs a coating for corrosion. |
|---|---|
| 1.4301 / 1.4404 | Corrosion-resistant and non-magnetic (austenitic); the default for exposed or wet service. |
| Aluminium 3003 / 5754 | Light, corrosion-resistant, good for housings that are not load-critical. |
| Brass / copper | For electrical or thermal function; usually stamped or drawn in thinner gauges. |
For a bearing seat, the material’s hardness matters as well as its corrosion behaviour – a soft cup can be indented by a bearing that is pressed and then loaded. We will flag it if the material is too soft for the press fit the customer specified.
An H7 bore is reached by sizing, not by drawing alone
Can you hold an H7 bore in a drawn cup? Not purely by drawing for most sizes; we get close and, where an H7 fit is genuinely required, add a sizing or boring operation on the bore. We will say which is needed rather than promise a draw that cannot deliver it.
How deep can a cup be before the bore goes out of straightness? Around 2× diameter for a single draw; beyond that, a guided redraw or a sizing step is required.
Can you form a bearing retention lip in-die? Yes, and it is normally cheaper than adding a circlip or a staked washer.
What finish do you recommend for a pressed bearing? Ra 0.8-1.6 µm on the bore; smoother is not always better, and we match the finish to how the bearing is retained.
Specifying a functional cup
Send the bore fit and its tolerance class, the engagement length, the base load and thickness, the press or retention method, the finish requirement on the functional surfaces, and the environment. With those we can tell you which features the draw can hold and which need a secondary operation, and quote a cup that assembles cleanly instead of one that fits on the bench and binds on the line.
Our deep drawn covers guide puts numbers to the design decisions behind a part like this — draw ratio, wall thinning, radii and trim; the Precision Deep Drawn Parts pages collect the rest of the family.
Specifications
| Item | Deep drawn cup |
|---|---|
| Brand | AUNOV |
| Designing | Made to your 2D/3D drawings (PDF, DWG, STEP, IGS) – DFM notes are returned before any tooling is cut; revisions are re-quoted once rather than silently absorbed. |
| Tooling | Tooling is built and held under your part number, so tooling lead time stays under our control, and first-article timing is measured from the tooling start date. |
| Samples | Production does not start until the sample report has been signed off. |
| Materials | Materials held include carbon steel, 304 / 316 stainless steel, aluminium and brass; mill certificates and heat numbers accompany the first article. |
| Surface finish | Zinc, nickel or chrome plating, anodising, passivation or e-coat; alternatives quoted with the quotation, samples approved in writing. |
| Processing | Progressive drawing through several stages, annealed between draws, then trim and pierce; first articles verify the whole flow before the run is released. |
| Equipment | Mechanical presses from 5 to 250 T and hydraulic presses 250-500 T, with in-line annealing furnaces; secondary ops run on CNC turning centres, inspection on the CMM. |
| Tolerance | +/-0.05 mm to +/-0.1 mm across the part, wall thickness held to print; finer bands confirmed from capability data before quoting. |
| Delivery terms | FOB Ningbo or Shanghai, T/T with deposit and L/C for larger runs; price breaks tie to annual volume. |
Frequently Asked Questions
What makes a cup functional rather than just a closed cylinder?
Something has to sit in it. A bearing seat, a guide or a socket turns the cup into a locating feature, and suddenly the inside surface is the functional one rather than the outside. Specifying it as a container instead of as a bore is the usual reason a cup measures correctly and still will not accept the part that belongs in it.
If only three dimensions matter on a cup, which are they?
The bore that receives the part, how far that bore runs, and the squareness between them. Those three decide whether whatever goes in actually goes in and stays aligned. Almost every other dimension on the drawing exists to support one of them, so working from the bore outwards saves both time and argument compared with dimensioning from the outside diameter inwards.
Bearing seat or guide – does the specification differ?
Yes, in what has to be held. A bearing seat cares about roundness and how load enters the wall, because a bearing loads a limited area. A guide cares about consistency over the whole length, because whatever travels through it sees every part of that distance. Choosing the wrong emphasis measures the right thing and still lets the part fail in service.
Where does the load actually go – through the wall or through the base?
Through whichever the assembly loads, and that is rarely stated. A cup taking axial load puts it into the base thickness; one taking radial load puts it into the wall. Base thickness is the dimension most often absent from cup drawings and most often needed, which is why it belongs on the print rather than following implicitly from the wall call-out.
Related Products
Request a Quote for This Part
Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).




