
The Oil Pump Electric Motor Enclosure lives in fluid: immersed in or splashed by the very oil the pump moves. That duty changes the material decision, the sealing design and the tests that matter. This page is written for pump OEMs specifying a drawn motor enclosure for wet sump and circulating-oil service.
What oil duty changes
- Material: stainless steel earns its place. Long immersion in warm mineral or synthetic oil with additives attacks plain carbon steel coatings over time. 304 stainless steel as-drawn is the default for permanent immersion; carbon steel with robust plating remains valid for splash-only, ventilated duty – and we will say which side your print falls on.
- Seals replace gaskets. A static O-ring on a machined land, not a slip-on gasket. The seal face finish and flatness become first-order specifications, not afterthoughts.
- Pressure and leak testing move into the plan. Where the shell is part of the fluid boundary, leak testing is written into the quality plan by agreement, with results in the shipment file.
- Thermal continuity. Oil-cooled motors depend on the shell conducting heat into the fluid; a drawn seamless wall conducts uniformly – a welded seam is a local thermal resistance and a corrosion site at once.
Geometry limits worth knowing before you draw the print
Oil-pump motor enclosures tend to be deep for their diameter – the pump stack sets the length. Two limits shape the drawing route:
- Depth-to-diameter beyond 2:1 needs staged drawing with interstage annealing; on stainless steel, more stages still. It is routine work here – hydraulic presses 250-500 T with in-line annealing exist for exactly this – but it should be planned, not discovered.
- Cavity depth and seal face finish are the named first-article measurements on this part family, alongside the standard wall-thickness check at the thinnest section after forming.
Integration with the pump assembly
The enclosure usually carries more than the motor: mounting feet or a flange that registers into the pump housing, cable entry rated for the environment, and sometimes ports tapped into the drawn wall. Machined features are turned to ±0.03 mm on our CNC centres in the same setup as the bore where possible, so concentricity between drawn shell and machined seat does not stack across vendors.
Quality plan for fluid-boundary shells
- Mill certificates per incoming heat; 316 substitution only with written approval.
- CMM first-article report: cavity depth, seal face finish, wall thickness at the thinnest section, mounting datums.
- Leak and pressure testing per the agreed plan, certificates in the shipment file.
- Sampling-plan inspection per batch under ISO 9001 certification.
Commercial frame
Tooling is built in our own toolroom and held under your part number, with the charge refundable against agreed volumes. Feasibility questions about walls, threads or tolerances are answered before quoting; changes are priced before they are made. FOB delivery as standard with DDP for EU and US addresses; call-off schedules supported so pump programmes can pull to demand.
Our deep drawn covers guide puts numbers to the design decisions behind a part like this — draw ratio, wall thinning, radii and trim; the Precision Deep Drawn Parts pages collect the rest of the family.
Fluid-boundary integrity at the shaft exit
An oil-pump motor enclosure sits on the fluid side of the seal, so its most important feature is the shelf and bore where the shaft leaves the motor. We draw that seal seat concentric to the bearing pilot and hold its face flat, because any runout there walks the shaft seal and the pump starts weeping long before the winding fails. The enclosure is therefore detailed around the shaft exit first and the outer shell second. We verify the seat on the first article with a concentricity check against the pilot, not against the outer diameter, because that is the relationship the pump actually cares about.
Serviceability versus sealed construction
Oil-pump assemblies are opened for maintenance, so we weigh a resealable enclosure against a sealed one and recommend the resealable joint wherever the motor will be serviced in place. The fastening and gasket are chosen so the original clamp load is restorable with standard tools, which keeps the IP rating through repeated opening. Where the duty demands a sealed unit, we size the wall so the enclosure survives as a replace-on-service part and document that expectation in the quotation so the pump builder plans inventory accordingly.
Corrosion at the fluid interface
The metal at the shaft exit sees both oil and the atmosphere, so we specify a material and finish that resist that mixed environment rather than the interior alone, because that interface is where enclosures actually fail.
Shaft seal selection at the pump interface
The enclosure meets the pump at the shaft, and the seal there is chosen for the fluid and the speed rather than taken from a shelf. A lip seal is cheap and fine for light duty but wears with shaft finish; a mechanical seal lasts longer under pressure but needs more axial space the enclosure has to provide. We size the seal pocket so the selected seal seats without crushing its spring, and we hold the shaft finish the seal specifies because a rough shaft is what kills a lip seal early. The enclosure is therefore detailed around the seal first, and the outer shell second, which is the order the pump actually experiences the part in.
Specifications
| Item | Oil pump electric motor enclosure |
|---|---|
| Brand | AUNOV |
| Designing | Your drawing sets the part – unusual walls, threads or tolerances are feasibility-checked first; changes are priced before they are made. |
| Tooling | Dies, fixtures and gauges are made in our own toolroom, so tooling lead time stays under our control, and the charge is refundable against agreed volumes. |
| Samples | Samples are issued for approval before the run, so the sample is retained as the master, and production starts only after your written sign-off. |
| Materials | Carbon steel (SPCC / DC01), 304 / 316 stainless steel, aluminium, brass and copper – the grade is matched to the duty of this enclosure. |
| Surface finish | Plating, powder coating, anodising or polishing, per the print; the agreed finish travels with the part number. |
| Processing | Multi-stage deep drawing with interstage annealing, trimmed and pierced in following dies; in-process checks sit between stages, not only at the end. |
| Equipment | Mechanical presses from 5 to 250 T and hydraulic presses 250-500 T, with in-line annealing furnaces; secondary ops run on CNC turning centres, inspection on the CMM. |
| Tolerance | +/-0.05 mm on drawn diameters, tighter bands confirmed against the drawing; capability is checked on the first article before the run continues. |
| Delivery terms | FOB Ningbo or Shanghai, payment by T/T, L/C at sight or D/P; call-off schedules are supported. |
Related Products
Frequently Asked Questions
What does oil duty change compared with a dry enclosure?
More than the sealing. Oil attacks some finishes, it wets surfaces that a dry enclosure would keep clean, and it demands that every joint remain sound rather than merely close. Its one advantage is that internal pressure is often lower, so the requirement moves from strength towards containment discipline and material compatibility.
Which geometry limits are worth knowing before drawing the print?
Depth relative to diameter, because the pump stack sets the length and these enclosures end up deep for their width. That combination drives the number of draw stages, how straight the part stays, and where thinning lands. Discovering it afterwards means redesigning around the stack rather than choosing a sensible shell in the first place.
Why is the shaft exit the awkward place on this part?
It is the one dynamic interface. Everywhere else the enclosure can be drawn as continuous material with no joint, while the shaft has to leave through it while rotating. That single location carries the sealing requirement, the alignment requirement and usually the wear, so it deserves to be specified separately from the rest of the shell.
What does quoting against the pump assembly need beyond the part drawing?
The interfaces. Which faces mate to the pump body, where ports sit relative to those faces, and how the assembly is clamped, because each decides features on the shell that the shell drawing alone does not show. Missing that information tends to produce a part that is individually correct and collectively unusable.
Request a Quote for This Part
Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).




