Oxygen Sensor Can – Measuring End Shell

Oxygen sensor can
Oxygen sensor can

The oxygen sensor can is the small drawn shell at the measuring end of the sensor. It looks like a trivial part, and the reason it is worth a page is that almost everything about its performance is decided by how it is formed rather than by what it is made of.

Why it is drawn and not machined

The can is a thin-walled shell with a closed or louvered end and a pattern of gas openings. Machining one from bar or tube is possible and is the slower, more expensive route, and it would still leave a weld somewhere in a part that lives in exhaust gas. Drawing produces the shell as one seamless piece: no joint to open at temperature, no weld to crack under thermal cycling. It also produces the openings in the die, which means the pattern that governs gas access is identical from the first part to the ten-thousandth instead of depending on a second operation.

Thin is a feature here, not a cost saving

The can is deliberately thin. A thinner shell has less thermal mass, so it tracks the exhaust’s temperature swings instead of lagging them, and the sensor reads a changing exhaust rather than a smoothed one. The trade-off is that a thin shell has little margin against scaling and internal oxidation on both faces, which is why the wall thickness and the grade are chosen together rather than separately.

The openings are formed, and their edges decide the part’s life

The gas access openings are not holes punched in a finished can; they are formed features, and their rims are where this part fails. A sharp rim is both a stress concentrator under thermal cycling and the place oxidation starts, because a sheared edge exposes fresh metal with no protective scale. Where the design allows it we form those rims with a rolled or coined edge. The pattern itself matters as much as the edges: too little open area and the sensor’s response lags, too much and the ceramic inside is exposed to water splash and particulates.

Geometry is designed before tooling, not after a failure

Thermal shock concentrates at every geometric discontinuity – the corner at the closed end, the shoulder where the can meets the housing, the rims of the openings. Those transitions are given generous radii in the die design, because a can that survives a static high-temperature soak and then cracks in service has a geometry problem that a better grade will not fix. Where the application is severe, the geometry is validated on a thermal shock rig before tooling is cut.

How a can is checked before it ships

The opening pattern, the formed rims and the wall are inspected on first articles, and the shell is checked for the seamlessness that is the reason for drawing it in the first place.

First articles and retention samples are kept for the programme, so a reorder reproduces the same wall, the same opening pattern and the same formed edges. On a part whose life is set by its geometry, that is what keeps the second batch behaving like the first.

Our Sensor Housings range is where this part sits. The sensor housings pages carry the process notes, common materials and inspection points behind every product in the family.

Where this part is used

The measuring-end shell of an exhaust-gas oxygen sensor is the classic home for this part: a small drawn can that holds the sensing element, positions it in the exhaust stream and survives the temperature and chemistry of the stream itself. The same shell geometry turns up in NOx sensors, in temperature sensors mounted in the same exhaust tract, and in industrial gas-analysis probes where the element needs to sit in the flow rather than behind a wall. In every case the shell is a functional part of the measurement, not a package around it.

Because almost everything about the part is decided by how it is formed, the interesting requirements are the thin wall, the formed openings and the edge condition those openings leave behind. A machined version of the same can would be possible and would cost several times more.

What we need to quote it

Send the sensing element drawing, the leak specification the assembly has to meet, and the exhaust-side temperature the shell sees in service. Tell us whether the shell is welded or crimped downstream and what the sealing face has to be, because that decides whether we machine the seat or leave it as drawn. A sample to measure is just as useful as a drawing if the element is proprietary.

Specifications

ItemOxygen sensor can
BrandAUNOV
DesigningSend drawings, or send a sample to be measured – unusual walls, threads or tolerances are feasibility-checked first; the same drawing is used for every repeat order.
ToolingTooling is built and held under your part number, so die cost stays transparent, and ownership is confirmed on the quotation.
SamplesPre-production samples come with a full inspection report, so the sample is retained as the master, and the signed sample is kept for future reorders.
MaterialsCarbon steel, 304 / 316 stainless steel, aluminium and brass are all held in stock; mill certificates and heat numbers accompany the first article.
Surface finishFinish selected from the drawing: plating, coating, anodising or passivation; masking and laser marking available where needed.
ProcessingWhere the print calls for them, seats and threads are machined into the drawn shell; batch records on file mean repeat orders start from approved data.
EquipmentHydraulic drawing presses and CNC lathes for sealing faces, with CNC turning centres for secondary operations and CMM inspection.
Tolerance+/-0.02 mm on machined seats, sealing faces flat to drawing; capability is checked on the first article before the run continues.
Delivery termsFOB Ningbo or Shanghai, payment by T/T or L/C, quoted in USD or EUR; sea or air freight is quoted to your door.

Frequently Asked Questions

Why is this can drawn rather than machined from solid?

Because the wall behaves differently. Machining leaves whatever wall the cutter is set to, uniform and comparatively thick; drawing leaves a wall that thins where it formed, and at this size that wall is thinner than any economical machining would attempt. Since the whole point of the part is to bring gas to an element quickly, the thin drawn wall is doing useful work rather than representing a compromise to save money.

Why do the formed openings decide how long the can lasts?

Every opening interrupts the protective section and collects stress, so the can fails at the edge of one of its own features rather than in the middle of a panel. Edge condition matters more than size here: a torn or heavily work-hardened edge nucleates cracking where a clean one does not. That is why the edge requirement belongs on the drawing rather than being left to deburring practice.

Should the can geometry be settled before tooling is quoted, or can it follow?

It should be settled first. The draw sequence, how the openings are formed and where the part trims all follow from the final geometry, so changing that geometry afterwards means changing all three. Most of the expensive changes in this family are geometry decisions revisited too late, which is why the manufacturability review runs alongside the quotation rather than after it.

What actually gets checked on a can before it ships?

The features that carry its function rather than the ones easiest to measure: the condition and position of the openings, the wall at the point where it thinned most, and whatever surfaces the assembly registers on. Once the process is stable, sampling replaces piece-by-piece checking, but that rests on a first article measured against all three rather than against the drawing’s general tolerance block.

Request a Quote for This Part

Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).