Stainless Steel Spray Nozzles with Brass Vane

Steel Splined Gear Shafts, Three-Piece
Steel Splined Gear Shafts, Three-Piece

A spray nozzle is an orifice and a vane, and the vane is the part that makes it a design rather than a measurement. The orifice sets the flow; the vane sets the shape of the spray. And the vane is made of brass while the body is stainless steel, which is not an accident of material availability – it is the standard solution to a problem that stainless steel cannot solve on its own.

So this page is about a mixed-material part where each material is doing the job it is good at, and where the joint between them is a real engineering feature rather than a convenience.

Why the vane is brass and the body is stainless steel

A vane is a thin, flat, shaped piece of metal that sits in the fluid and controls the flow’s shape. The requirements on a vane are:

  • Shape accuracy. The vane’s profile determines the spray’s pattern, its thickness, and its penetration. The profile has to be accurate and consistent from part to part, because two nozzles with the same orifice and different vanes will produce visibly different sprays.
  • Low mass and low inertia. The vane has to respond quickly and it has not to carry momentum that would fatigue its mounting.
  • Formability. The vane is usually a thin strip that is cut or formed to shape, and the material has to be formable enough to be made that way.

And here is the problem with stainless steel on this part, and it is specific: thin stainless steel strip work-hardens severely when it is formed, and a thin formed stainless steel vane will crack at the forming radii. The forming operation is exactly what a vane’s shape requires, and stainless steel is the worst of the common metals for it. Brass does not have this problem – it forms beautifully, it takes a fine edge, and it is light enough to be a vane.

So the standard solution is a stainless steel body – for the corrosion resistance and the pressure duty and the nozzle’s mechanical strength – with a brass vane – for the formability and the shape accuracy. And that solution creates the part’s most interesting feature, which is how the two are joined.

The vane’s mounting, which is the joint

A vane has to be held in the nozzle body with its shape correctly oriented and with its edges sealed, because if the vane’s edge leaks past it the spray pattern changes. Four mounting arrangements, and each has different requirements.

  1. Slotted retention. The vane slides into a slot in the body and is held by geometry – a ledge, a clip, or the body itself. Simple, no fasteners, and the vane’s position is set by the slot’s width and by what retains it. The requirement is that the slot’s width holds the vane’s thickness consistently and that the retention cannot allow the vane to lift.
  2. Retained by a separate clip or ring. A wrap-around clip or a retaining ring holds the vane against its seat. This allows the vane to be replaced, and it means the seat’s flatness and the clip’s retention force are both functional.
  3. Screwed or fastened. Unusual on a vane because a fastener’s protrusion into the flow path would disturb the spray, and because a threaded fastener in a thin body is fragile.
  4. Bonded. Adhesive bonding is used on some designs, and it brings a vane assembly that is a separate part – which is why vane assemblies are often specified and supplied as matched sets with the vane and its holder already assembled.

Whichever it is, two things have to be specified: the vane’s position relative to the orifice – because the spray depends on the distance and the angle between the vane and the orifice – and the vane’s sealing at its edges, because a leak past the vane’s edge bypasses it and the spray changes. On a nozzle with a defined spray pattern, the vane’s edge seal is as functional as the vane’s profile.

The orifice, which is the other half

The orifice sets the flow and it is covered in detail on the chrome-plated nozzle page elsewhere in this section, but two points are specific to this part because of the vane’s presence.

  • Orifice diameter and spray angle are coupled through the vane. The same orifice with different vanes gives the same flow and different patterns, so a nozzle’s flow specification and its pattern specification are two separate requirements and both are needed.
  • The orifice’s position relative to the vane has to be held tightly, because the spray pattern is very sensitive to the distance between the two. This is a relationship between two features on the same part and it is the tolerance that most needs stating as a relationship rather than as two independent positions.
  • The orifice’s own condition. On a spray nozzle the orifice’s surface finish and its edge condition affect the spray – particularly a coarse orifice wall, which produces a poor atomisation pattern rather than a fine one. And any burr at the orifice’s exit will distort the spray visibly.

The material pairing, and the galvanic question

Standard stock: carbon steel, 304 and 316 stainless steel, aluminium and brass, with the final grade fixed at the drawing review. On this part the pairing raises three specific points.

  • The body is stainless steel and 316L is the normal choice, decided by the fluid. Where the fluid is water and the environment is clean, 304 may be sufficient; where there are chlorides, a cleaning regime, or a food or pharmaceutical application, 316L. And the L grade if there is any welding or heat input.
  • The brass vane in a stainless steel body is a galvanic couple, and on a wet-side part that is a real mechanism. The area ratio works in the vane’s favour – the vane is small and the body is large – which means the vane corrodes preferentially where they touch. On most nozzle applications this is acceptable because the vane is a replaceable item and the corrosion is slow. Where it is not acceptable, the mitigation is a coating on the vane, a different vane material, or a seal between them that isolates the two.
  • The material change at the vane’s seat has a dimensional consequence if the two are joined by anything other than a mechanical arrangement – because brass and stainless steel expand at different rates and a bonded or welded joint between them will see shear across the interface as the temperature changes.

Spray pattern, which is the requirement the drawing cannot express

A nozzle’s spray is a function of its orifice, its vane, its internal chamber geometry, and the fluid’s pressure and viscosity. Only the first two are dimensions. The consequence is that a spray pattern has to be specified by something other than geometry, and there are three ways, in increasing order of rigour.

  1. By description – a fan, a cone, a full cone, a hollow cone, with a nominal angle. This is what most drawings say and it is weak, because a 60-degree fan from one supplier and a 60-degree fan from another are visibly different.
  2. By an approved sample or a master nozzle, which is the practical standard and works well. The nozzle is compared against a retained reference, ideally on a test rig at a stated pressure, with the liquid’s identity stated because the pattern depends on it.
  3. By a measured performance figure – a spray angle measured on a test bench, a droplet size distribution, a coverage pattern, or a flow rate at a stated pressure. This is the most rigorous and it requires the supplier to have the test equipment and it requires the customer to specify what to measure.

The thing worth saying plainly: flow rate at a stated pressure is measurable and should always be specified; spray pattern is measurable but needs a method. Where the pattern matters – a coating application, a cooling spray, a cleaning spray, a dosing application – the pattern should be tied to an approved sample or a bench measurement, and the pressure and fluid stated, because the same nozzle at a different pressure produces a different pattern.

The orifice and the vane geometry are flagged as one relationship

+/-0.01 mm on machined faces and +/-0.05 mm on formed details, capability checked on the first article. On this part the flagged dimensions are the orifice and the vane’s geometry and their relationship.

  • Orifice diameter, measured, on every part, with the measurement method stated. On a calibrated nozzle this is the tolerance that carries the flow specification.
  • Orifice roundness and edge condition, no burr.
  • The vane’s profile, verified against the master, and the vane’s thickness.
  • The distance and angle between the vane and the orifice, as a relationship, held tightly because the spray pattern is sensitive to it.
  • The vane’s seating and its edge seal, verified by a visual check against an approved standard and functionally by a flow test.
  • The body’s internal chamber geometry where it is significant, since the chamber’s shape also affects the pattern.
  • General dimensions and the thread at a general band and a stated class.

Flow rate at a stated pressure is the number the customer is buying

  1. Flow rate at a stated pressure, on every part where the nozzle is calibrated. This is the measurement that tests the specification the customer actually buys and it is quick on a test bench.
  2. Spray pattern against an approved master, on a sample or on every part, with the pressure and the fluid stated.
  3. Orifice diameter and edge condition, on every part.
  4. The vane’s profile and its seating, visually against the master, with the edge seal verified.
  5. A functional leak or pressure test on the body, where it is a pressure part.
  6. CMM data on the vane-to-orifice relationship, and on the orifice, with a dimensional report on the first article.
  7. Batch records filed so a repeat order starts from approved data – and on a nozzle with a vane this matters more than on most parts, because a vane is a matched component and a repeat order with a different vane will produce a different spray.

Whether the pattern matters, or only the flow

Is the spray pattern a requirement, or is the flow rate the requirement and the pattern whatever comes out? Those two answers change the part substantially and they are frequently conflated. If the pattern matters – a coating that has to cover a specific area, a spray that has to penetrate, an atomisation requirement – then the vane is the design and it needs to be specified, matched, and verified against a standard, and the nozzle’s cost includes that verification. If only the flow matters, the vane may be a simple deflector and the nozzle becomes primarily an orifice with a flow specification, which is a cheaper and much easier part to make repeatably. Adding to this, two facts are worth asking for at the same time: what the fluid is, and at what pressure. A nozzle’s spray pattern is a function of the fluid’s viscosity and surface tension as much as of its geometry, so a pattern verified on water tells you very little about the same nozzle spraying a viscous or a volatile fluid. Fluid and pressure stated, and whether the pattern is a requirement – four pieces of information that cost one line on an enquiry and that turn a nozzle from a made-to-size part into a specified product.

You will find this part in our CNC Machining Parts range. Process notes, common materials and inspection points for every product in the family are collected across the cnc machining parts pages.

Specifications

Frequently Asked Questions

A brass vane in a stainless steel body splits the duties – what decides the split?

Direct answer: Because the two do different jobs. The vane has to be light and formable so it moves freely, and brass machines and moves well; the body has to resist corrosion and carry the load, and stainless steel does that. The two materials are chosen for their own duties, and the joint between them is then the design’s real problem.

Brass and stainless steel on one part form a galvanic couple – where does it bite?

Direct answer: That brass and stainless steel are a galvanic pair, and in a wet environment the brass is the anode that corrodes. The joint has to be isolated or the pairing accepted, and the material choice is made with that coupling in mind rather than per part alone.

The spray pattern is a requirement the print cannot carry – how is it checked?

Direct answer: The spray pattern. The drawing can specify the orifice and the vane’s geometry, but the spray pattern – the shape the fluid forms as it leaves – is a system property that only a test reveals. So the orifice and the vane geometry are flagged as one relationship, and the pattern is verified by test rather than read off the print.

ItemStainless Steel Spray Nozzle with Brass Vane
BrandAUNOV
DesigningYour drawing sets the part – unusual walls, threads or tolerances are feasibility-checked first; revisions are re-quoted once rather than silently absorbed.
ToolingDie design and toolmaking stay in house, so the die charge appears as its own quotation line, and ownership is confirmed on the quotation.
SamplesSample parts are measured and reported before submission, so any deviation is corrected at sample stage.
MaterialsStandard stock: carbon steel (SPCC / DC01), 304 / 316 stainless steel, aluminium, brass; the final grade is fixed with the drawing review.
Surface finishPlating, powder coating, anodising or polishing, per the print; the finish is inspected with the dimensional report on the first article.
ProcessingBar-fed turning with milled features completed in the same clamping; batch records are filed so a repeat order starts from approved data.
EquipmentBar-fed CNC turning centres plus 3- and 4-axis machining centres, with CNC turning centres for secondary operations and CMM inspection.
Tolerance+/-0.01 mm on machined faces, +/-0.05 mm on formed details; capability is checked on the first article before the run continues.
Delivery termsFOB Ningbo or Shanghai, payment by T/T or L/C, quoted in USD or EUR; call-off schedules are supported.

Request a Quote for This Part

Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).