
A hole through a camera housing is a hole in the image, and that is the whole problem
A pierced aluminium camera housing carries a camera module and has holes through it. The holes are for mounting, for connectors, for ventilation, for a window, for a cable, for a strap. Every one of them is a deliberate breach of the housing’s enclosure – and on a camera, a hole also appears in the image, because light that enters through a hole and reaches the inside of the housing can scatter onto the sensor. What that means in practice is that a pierced camera housing is not a general enclosure with holes; it is an optical part with a specified pattern of openings, each of which has a reason and a treatment.
We deep draw from coil or blank with in-process annealing so walls thin evenly, and every stage is logged against your part number, on mechanical presses 5-250 T plus hydraulics 250-500 T with in-line annealing, backed by CNC turning centres and a climate-controlled inspection room. Drawn diameters to +/-0.05 mm with tighter bands confirmed against the drawing, and finer bands confirmed from capability data before quoting. Standard stock is carbon steel in SPCC and DC01 grades, 304 and 316 stainless steel, aluminium and brass, with grade and temper confirmed in writing before tooling. Surface treatment is matched to the duty – plating, coating or polishing – with the agreed finish travelling with the part number. This page is about the holes, and about the four questions that decide what each one is for.
Every hole on a camera housing is one of five things
The classification matters because each category has a completely different requirement, and a drawing that lists holes without saying which category each is in has not specified the housing:
| Mounting holes | Pass through the wall to accept a fastener into something behind. The optical concern is stray light entering through the hole and bouncing onto the sensor. The usual treatment is a light trap – a counterbore, a washer that blocks the path, or a labyrinth. The mechanical concern is that the hole removes wall material from a region that may be carrying load, so its edge distance and its position to the mounting pattern matter. |
|---|---|
| Connector or cable openings | Typically a single larger opening that a connector or a cable gland seals. This is the most common breach on a camera housing and the easiest to handle, because a properly seated connector with a gasket closes the hole. What matters is the seal’s specification and the opening’s edge condition, and on a housing with a light-tight requirement the connector’s light sealing is a separate matter from its water sealing. |
| Ventilation holes | Small holes or a vent, to manage condensation and heat. On a camera this is a genuine conflict: a vent solves the thermal and condensation problem and creates a light path. The answer is a labyrinth or a hydrophobic sintered vent, and a vent’s location matters – a vent near the sensor is worse than a vent far from it. |
| Optical window openings | The opening the lens looks through. This is the one hole that is supposed to let light in, and its requirements are optical: diameter, position to the sensor, and edge condition. It is usually the largest precisely-machined feature on the housing. |
| Manufacturing and assembly holes | Sprue gates, alignment pins, ejector features. If any of these are on the finished part they are a defect, and if they are on a hidden face they are a light path that nobody specified. They should be on the drawing as features to be removed, or eliminated by designing the process so the part is trimmed out of the frame without leaving a hole. |
Stray light, and the four things that actually help
On a camera housing, a bare hole is a light path. Four mitigation approaches, and they are worth specifying rather than assuming:
- Make the hole small relative to its length. A small hole through a thick wall is a better light path than a small hole through a thin one. On a drawn housing the wall is thin, so a small hole is a short light path – which is why the wall’s thickness is part of the light-tightness calculation and not just a structural number.
- Break the straight line. A counterbore, a step, a washer that overhangs the hole, or a labyrinth means light entering the hole has to turn a corner to reach the interior. This is the cheapest and most common solution and it is entirely a design feature.
- Absorb rather than reflect. A matte black interior around a hole means light that does enter is absorbed rather than reflected toward the sensor. This is why the interior’s finish matters on a pierced housing specifically.
- Keep the holes away from the sensor. Location matters. A hole on the opposite side of the housing from the sensor, pointing away from it, is far less of a problem than a hole adjacent to the sensor’s edge.
How holes are made, and why it changes them
Deep drawing from coil or blank means the holes are pierced after the wall is formed, and this has three consequences on a part where hole position and hole shape matter:
- Position accuracy on a formed wall is worse than on a flat one. A hole pierced in a formed wall inherits the forming variation underneath it. Where a hole has to be accurately positioned – a mounting hole that has to line up with a bracket, a window aperture that has to be optically centred – this matters, and the answer is to machine the feature or to pierce it in a flat preform.
- A pierced hole in a formed wall is not round. The punch sees a curved, work-hardened surface, so the hole is slightly oval and slightly out of square to the wall. On a window aperture or a locating hole, roundness is a separate requirement from size.
- The burr side is determined by the piercing direction, and on a housing where the wall is pierced in two operations on opposite sides, or where the burr ends up in the interior, the burr’s direction is a design choice. A burr in the interior of a camera housing is both a light-scattering point and, on an optical housing, a defect.
A pierced housing wants aluminium for its finish and its weight
Standard stock is carbon steel in SPCC and DC01 grades, 304 and 316 stainless steel, aluminium and brass, with grade and temper confirmed in writing before tooling. On a pierced camera housing:
- Aluminium is the normal choice. It is light, it takes a black anodised finish that solves the interior’s light-scattering problem as well as the exterior’s, and it machines well where a window or a locating feature has to be machined. The 3003 and 1050 grades form the pierced holes most cleanly; 5052 is stronger and forms less cleanly; 6061 is for a housing with significant machining.
- Stainless Steel for a harsh or corrosive environment, and 316 for salt or marine. It is heavier, it does not take a black anodised finish, and the interior’s light-scattering requirement needs a separate coating – so the interior finish is a distinct specification on a stainless steel camera housing.
- Carbon steel with a coating is a cost option and it is heavy and thermally isolating, which on a camera is usually the wrong direction.
Finishing, and the masking on a pierced part
Surface treatment is matched to the duty – plating, coating or polishing – with the agreed finish travelling with the part number. On a pierced camera housing:
- Mask the window aperture and the optical seats absolutely. These are the features where a coating would be a functional defect rather than a dimensional one.
- Mask the holes that take fasteners, where the fastener’s bearing face or the thread matters. A plated hole is smaller than a bare one, and on a mounting hole that is a fit change.
- Consider masking the interior of a vent. On a vent that is a light path, a coating inside the vent changes its geometry and may close the labyrinth.
- Anodising on aluminium solves the interior’s problem. A black anodised finish is matte and low-reflectance, which is exactly what a camera housing’s interior needs – so the finish that solves the exterior’s appearance requirement also solves the interior’s optical one. That is a genuine argument for specifying black anodising rather than a coating.
Every hole is a breach in whatever it was
Eight things, and the first is the one that makes this a specified part rather than a drilled part:
- Every hole, listed, with its function – mounting, connector, vent, optical, or manufacturing – because each function carries different requirements and the function is what tells a reviewer what to check.
- For every light-path hole, its light-trap treatment, stated as a feature – a counterbore, a step, a labyrinth – rather than left to a reviewer’s discretion.
- The window aperture, if there is one: diameter, roundness, position to the sensor, and edge condition, at the tight band.
- Vent position, relative to the sensor, and the vent type if it is not a bare hole.
- Whether each hole is pierced or machined, and the tolerance on its position. A tight positional requirement on a pierced hole is a capability question and should be confirmed before quoting.
- Drawn diameters at the stated band, with the wall held to print and its minimum location identified.
- The interior’s surface requirement, where the housing carries an optical function – a matte, low-reflectance interior stated as a requirement.
- Material grade and temper, and which surfaces are masked, with dimensions stated before or after finish.
How many of these holes does the housing need?
How many of these holes does the housing actually need? Every hole is a breach, and on a camera housing each one is a light path, a water path, a dirt path, and a thermal path. Holes added one at a time during a design cycle accumulate into an enclosure that is much more compromised than the individual holes suggest, and the accumulation is not visible until the housing is finished. Reviewing the hole pattern as a complete set at the design stage – and asking of each one what it is for – is worth more than any of the individual mitigations, because a hole that is removed needs no labyrinth, no masking, and no light trap. It is also the cheapest possible improvement, because it costs nothing and it is available before the tooling.
Choosing between drawing, machining and welding comes down to the shape of the part: the guide to deep drawn covers sets out where each route wins, and the overview page links through to the full Precision Deep Drawn Parts range.
Specifications
| Item | Hydroformed Pierced Aluminum Camera Housing |
|---|---|
| Brand | AUNOV |
| Designing | Your drawing sets the part – unusual walls, threads or tolerances are feasibility-checked first; changes are priced before they are made. |
| Tooling | Tooling is built and held under your part number, so die cost stays transparent, and the charge is refundable against agreed volumes. |
| Samples | The sample you approve becomes the gauge reference for production. |
| Materials | Standard stock: carbon steel (SPCC / DC01), 304 / 316 stainless steel, aluminium, brass; grade and temper are confirmed in writing before tooling. |
| Surface finish | Surface treatment matched to the duty: plating, coating or polishing; the agreed finish travels with the part number. |
| Processing | Deep drawing from coil or blank, with in-process annealing so walls thin evenly; every stage is logged against your part number. |
| Equipment | Mechanical presses 5-250 T plus 250-500 T hydraulics, with in-line annealing, backed by CNC turning centres and a climate-controlled inspection room. |
| Tolerance | +/-0.05 mm on drawn diameters, tighter bands confirmed against the drawing; finer bands confirmed from capability data before quoting. |
| Delivery terms | FOB Ningbo or Shanghai, T/T or L/C, with D/P accepted on repeat business; sea or air freight is quoted to your door. |
Frequently Asked Questions
Why pierce the holes into a drawn aluminium camera housing instead of machining them after?
Piercing in the die keeps each hole located by the same tool geometry that forms the shell, so the pattern holds across the run without a second setup that would drift. On a camera housing the holes are optical features as much as mechanical ones, so locating them in the draw rather than cutting them in afterwards is what keeps a window, a connector, or a vent in its place relative to the sensor.
How is stray light controlled at each hole of a camera housing?
Each opening is treated as a light path, not just a hole, so the mitigation is specified per hole – an internal baffle, a recessed seat, a masked window, or an absorbed finish on the bore – rather than left to chance. The page classifies every hole by what it does and what it therefore needs, because on a camera a bare hole is a path for light that scatters onto the sensor.
Why is aluminium chosen for a pierced camera housing?
Aluminium gives the weight saving a camera module wants and takes the fine finish a pierced part needs, with the grade and temper confirmed before tooling. Where the housing also carries the optical window, the same material plan covers the body and the mounting face so nothing fights the alignment.
What tolerance holds the hole pattern on a pierced aluminium camera housing?
Hole position and diameter are set by the pierce tool and held to a few hundredths of a millimetre, then checked on the CMM, because the holes locate the lens, the connector, and the vents against the drawn datum. Tighter bands are confirmed from capability data before quoting, and the first article is measured before the run continues.
Related Products
Request a Quote for This Part
Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).




