Hydroformed Aluminum Camera Housings

Drawn Aluminum Can with Oval Mounting Flange
Drawn Aluminum Can with Oval Mounting Flange

A camera housing has three alignments, and only two of them are mechanical

An aluminium camera housing holds a camera module – a lens, an image sensor, and usually some electronics – and its job is to hold all of them in a fixed relationship and to protect them. What makes a camera housing different from a general enclosure is that it carries optical alignment requirements, and optical alignment is a much stricter thing than mechanical fit. A housing that is dimensionally perfect in every direction a CMM can measure can still produce a blurred image, because the sensor has to sit at a defined distance and angle from the lens, and that relationship is not the same as any single dimension.

We multi-stage draw with interstage annealing, then trim and pierce in following dies, and first articles and batch samples are checked on the CMM, on a press shop with 5-250 T mechanical and 250-500 T hydraulic presses with annealing ovens on site. General tolerance on drawn sections is +/-0.1 mm with +/-0.03 mm on machined seats, and GD&T per the drawing with PPAP-style reports on request. Stock covers carbon steel in SPCC and DC01 grades, 304 and 316 stainless steel, aluminium and brass, with special grades sourced to the drawing when volumes justify. Plating, powder coating, anodising or polishing per the print, with finish thickness and adhesion checked on the first article. This page is about the three alignments, and about what each one costs to control.

Alignment 1: the sensor to the lens, which is optical

This is the alignment that determines whether the image is sharp, and it has three components that are each a separate tolerance:

  • Sensor-to-lens distance. The back focal distance, and it is sensitive in a way that is not intuitive. On a typical camera module the tolerance on this dimension is a few tens of microns, because a short lens has a shallow depth of field and a small change in distance shows as defocus. On a drawn housing this dimension is entirely set by the machined seat the module sits on, and it cannot be held by a draw.
  • Sensor tilt relative to the lens axis. A tilt – called tilt or skew – moves part of the image relative to the rest and causes corner softness. It is a parallelism requirement between the lens mounting axis and the sensor’s seating face, and it is a tight-band requirement in a direction that is genuinely different from any other tolerance on the part.
  • Lateral position. The sensor’s position in the image plane, which is what determines where the image centre is. This is looser than the two above but it is still a position requirement rather than a clearance.

The consequence is that a camera housing needs at least one machined feature whose purpose is purely optical, and usually two – the sensor seat and the lens mount. Everything else about the housing is ordinary enclosure work, and it is worth separating the two on the drawing so that the optical features are given the tolerance attention they need and the rest are not over-specified.

Alignment 2: the housing to its mounting, which is mechanical but unforgiving

The housing mounts to something – a bracket, a vehicle, a pole, a wall – and that mounting has to position the camera correctly. Three requirements:

  1. The mounting surface’s flatness. A housing that is not flat at its mounting face will be stressed when bolted, and a stressed housing is a housing whose optical alignment has moved. This is a direct link between a flatness requirement and an optical requirement, and it is worth stating on the drawing because it is not obvious.
  2. The mounting feature’s position to the optical axis. Where the mounting holes are relative to the lens axis determines how the housing rotates when it is bolted and how the camera is aimed. This is a position requirement with a specific datum – the optical axis, not the housing’s outline.
  3. Stiffness between the mounting and the sensor seat. A housing that is compliant between the mount and the sensor will move under shock or vibration, which is a temporary loss of alignment – an image that shakes or goes out of focus when the vehicle moves. For a camera in a vehicle, the stiffness between the mount and the optical bench is a real requirement and it is a structural one.

Alignment 3: the thermal path, which is the one people forget

A camera module generates heat, and heat in an enclosure is a problem for two separate reasons, one mechanical and one optical:

  • Mechanical: the housing moves. An aluminium housing expands about 23 microns per metre per degree. Over a 200 mm dimension and a 60 degree temperature change, that is about 0.28 mm – which is larger than most of the housing’s general tolerance band. So on a camera housing, thermal expansion is not a small effect; it is comparable to the whole tolerance structure. If the sensor’s position is defined by two features on the housing, the housing’s differential expansion moves it.
  • Optical: the module itself moves. The image sensor and the lens are usually on a common substrate inside the module, and the module’s own thermal expansion relative to the housing is what actually shifts the alignment. The housing’s job is to control the module’s temperature rather than to compensate for it – which means the housing is as much a heat sink as a structure.

So a camera housing that must hold alignment over a temperature range needs its thermal design specified, not left to the material choice. An aluminium housing with good thermal contact to the module is a heat sink; an aluminium housing with an air gap and a plastic interface is an oven. And the second one will meet every dimensional requirement and still lose focus over temperature.

Sealing and ingress, and the conflict with heat

Camera housings are frequently sealed to an IP rating, and sealing conflicts with the thermal requirement in a way that is worth recognising:

  1. A sealed housing traps heat. If the housing is sealed and the module runs warm, the interior temperature will exceed the ambient and there is no convection path out. A sealed housing needs a thermal path by conduction – through a designed heat-transfer surface to the mounting or to a heatsink – and that has to be designed rather than hoped for.
  2. A vented housing breaks the seal. A vent solves the thermal problem and creates an ingress problem. A hydrophobic or sintered vent is the standard compromise, and on a camera housing it is a real component with a specification, not a hole.
  3. The window is a weak point. A camera housing’s lens window – the optical aperture, or a protective window over it – is the most exposed feature and often the least protected. If there is a window, its material, its thickness, its coating, and its seal are all functional requirements, and an uncoated plastic window will fog, scratch, and yellow.

Material, and what it decides here

Stock covers carbon steel in SPCC and DC01 grades, 304 and 316 stainless steel, aluminium and brass, with special grades sourced to the drawing when volumes justify. For a camera housing:

AluminiumThe normal answer, and it wins on the two things that matter most here: it is light, and it conducts heat about twenty times better than stainless steel, so it is an effective heat sink for the module. It also machines well, which the optical features need. On a camera where the optical alignment drifts with temperature, the thermal conductivity is not a nice-to-have – it is the specification.
304 or 316 stainless steelWhere corrosion resistance dominates, where the environment is harsh, or where the housing must be robust rather than light. The penalty is thermal: stainless steel conducts badly, so the housing becomes a heat barrier and the module runs hotter, which can make the alignment worse. 316 for salt and marine.
Carbon steelNot a normal choice for a camera housing. It is heavy and a poor thermal conductor, and a housing that is heavy and thermally isolating will have a temperature problem.
BrassUnusual here, though it is used where a specific corrosion behaviour or a machined optical feature drives the choice.

Mask the optical surfaces absolutely on a camera housing

Plating, powder coating, anodising or polishing per the print, with finish thickness and adhesion checked on the first article. Three points specific to a camera housing:

  • Mask the optical surfaces absolutely. The lens mount’s seat, the sensor seat, and any locating feature must be uncoated. A coating there changes the dimension and, worse, a coating on an optical seat changes how the module is located in a way that is not a simple dimensional change.
  • Anodising is a good exterior finish on aluminium and it is dimensionally well behaved, which matters where a housing’s features are close-tolerance. It must be masked from the optical surfaces and from any thread.
  • The window’s surface, if there is one. On a camera the window’s optical quality matters more than on any other part in this family – it needs to be flat, to have a controlled coating or none, and to be free of scratches and marks. A housing with a window is a housing where the window is a separate quality specification.

The sensor sets the housing, not the other way round

Eight things, and the first three are the optical requirements that a general enclosure drawing would not have:

  1. Sensor-to-lens distance, tilt, and lateral position, stated as three separate requirements with the module’s mounting interface identified.
  2. Which feature is the optical datum, and the tight band that applies to the optical features as distinct from the general tolerance.
  3. Stiffness between the mounting face and the sensor seat, as a stated requirement or a deflection limit, because it is what holds the alignment under shock.
  4. Mounting face flatness, against a named surface, with the link to the optical alignment stated if the customer cares about it – which on a camera they should.
  5. Thermal requirement, – the module’s power and the maximum internal or housing temperature – because that is what drives the material and the heat path.
  6. Ingress rating, and every opening listed with its sealing method, plus any vent and its type.
  7. Window, if present, as a separate specification: material, thickness, flatness, coating, and seal.
  8. Which surfaces are masked, and whether dimensions apply before or after finish.

Is the camera module a purchased item?

Is the camera module a purchased item that defines the housing, or is the housing and the optical bench designed together? If the module is a purchased assembly with its own tolerances, the housing has to be designed around what the module tolerates – and the review should ask for the module’s datasheet, because a module’s sensor-seat tolerance and its thermal specification determine almost everything about the housing. If the housing and the optics are designed together, there is far more freedom to put the thermal path and the mounting stiffness where they need to be, and that is generally a better design. The question decides which of those two conversations is happening, and it is worth settling before the housing’s geometry is drawn rather than after.

Draw ratio, wall thinning, radii and trim — the design decisions behind a part like this are worked through with numbers in our deep drawn covers guide, and the Precision Deep Drawn Parts pages collect the rest of the family.

Specifications

ItemHydroformed Camera Housing
BrandAUNOV
DesigningYour drawing sets the part – samples are reverse-measured into a controlled drawing; the same drawing is used for every repeat order.
ToolingTooling is built and held under your part number, so tooling lead time stays under our control, and maintenance is tracked against the part number.
SamplesSample parts are measured and reported before submission, so the approved first article becomes the gauge reference, and mass production is gated on that approval.
MaterialsStock covers carbon steel (SPCC / DC01), 304 / 316 stainless steel, aluminium and brass; special grades are sourced to the drawing when volumes justify.
Surface finishPlating, powder coating, anodising or polishing, per the print; finish thickness and adhesion checked on the first article.
ProcessingMulti-stage deep drawing with interstage annealing, trimmed and pierced in following dies; in-process checks sit between stages, not only at the end.
EquipmentPress shop running 5-250 T mechanical and 250-500 T hydraulic presses, annealing ovens on site; first articles and batch samples are checked on the CMM.
Tolerance+/-0.1 mm general on drawn sections, +/-0.03 mm on machined seats; GD&T per drawing, PPAP-style reports on request.
Delivery termsCIF or DDP, with FOB available, T/T or L/C, with D/P accepted on repeat business; call-off schedules are supported.

Frequently Asked Questions

How are the three alignments held in a hydroformed camera housing?

A camera housing carries the sensor-to-lens optical path, the mechanical mount, and the thermal path, and hydroforming holds the first two off a single formed datum so they stay related. The optical and mechanical alignments are set by the tool; the thermal path is designed in rather than left to chance, because it is the one that drifts the image later.

Can a camera housing be sealed and still shed heat?

Yes, but the two requirements fight, so the seal and the thermal path are planned together. A hydroformed wall gives a continuous sealing land, and the material and any local thinning are chosen so heat still moves out where the electronics need it without breaking the ingress barrier.

Which material is used for a hydroformed camera housing?

Aluminium is the common choice for the weight and the way it forms and dissipates heat, with the specific grade picked for stiffness and EMI performance if the housing also shields the sensor. The material decision drives both the tolerances and the finish.

What is the minimum order quantity for a hydroformed camera housing?

Runs begin at 1,000 pieces, with the hydroform tool made in-house to your enclosure print. We quote within 24 hours of the drawing, and first articles are measured before the production run so the alignments are confirmed on metal, not just on paper.

Request a Quote for This Part

Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).