SS Deep Drawn Filter Cup with Perforated Base

SS Deep Drawn Filter Cup with Perforated Base
SS Deep Drawn Filter Cup with Perforated Base

A perforated base is thousands of tiny punched holes, and each one is a defect opportunity

A stainless steel deep drawn filter cup with a perforated base looks like a drawn cup with holes in it. In production it is the opposite: the cup is the easy part and the perforations are the whole difficulty. A filter base might carry anywhere from fifty to several thousand holes, and every one of them is a sheared edge with a burr, a potential blockage, a potential particle, and a place where the drawn wall’s thickness has to survive. Getting the perforations right determines whether the filter filters; getting them wrong makes it either blocked or leaky.

We multi-stage draw these with interstage annealing, then trim and pierce in following dies, and first articles verify the whole flow before the run is released, on mechanical presses 5-250 T and hydraulics 250-500 T with in-line annealing furnaces, with in-house toolmaking keeping dies and fixtures maintained. Tolerance runs +/-0.05 mm to +/-0.1 mm across the part with wall thickness held to print, and GD&T per drawing with PPAP-style reports on request. Stock covers carbon steel in SPCC and DC01 grades, 304 and 316 stainless steel, aluminium and brass, with special grades sourced to the drawing when volumes justify. Finish is selected from the drawing, with masking and laser marking available where needed. This page is about perforation, and about the four properties that decide whether a filter base works.

The hole has to be the right shape, not just the right size

A filter hole is not a round hole. The hole’s shape decides what passes through it, and this is the single most important thing about the drawing:

Round perforationsThe simplest and the most common. Simple to punch and to clean. They pass particles based on diameter, which means a long particle slightly smaller than the hole passes lengthwise – so a round-hole filter passes more than its nominal rating suggests.
Slotted perforationsLong narrow slots, oriented at 90 degrees to each other in an alternating pattern. They pass almost nothing longer than the slot’s short dimension, which makes them dramatically better at catching fibres, hair, and elongated debris. A slot’s width, not its length, is the filtering dimension.
Perforated with a larger supporting hole behind itTwo layers – a fine perforated sheet over a coarser support. This is how a real filter stack works, and it means the base is a laminate rather than a single wall. It is the right answer where the filtration requirement is fine but the pressure drop must stay low.
Etched or meshNot perforation at all, and much finer. A drawn-and-perforated base cannot filter to a fine rating; a fine rating needs a mesh or an etched screen, and the drawing should reflect that rather than specifying perforations finer than the process can produce.

So the drawing must state the hole’s shape, its short dimension, its long dimension where relevant, the pattern’s pitch, and the open area percentage. A drawing that says “perforated” and gives a hole diameter has specified something that is not a filter.

Perforation after drawing, and what that does to the wall

The sequence here – drawn, then trimmed and pierced in following dies – means the perforations are cut after the cup has been formed. That has three consequences:

  1. The wall thins around each perforation. Punching removes material and the surrounding metal deforms to accommodate the hole, so the wall immediately around a hole is thinner than the wall between holes. On a filter base where the wall is already thin from the draw, this matters – and where a perforation is close to a drawn feature’s bend or corner, the local thinning compounds.
  2. The holes are located on a formed surface. Position accuracy for a hole in a formed wall is worse than for the same hole in the flat. For a filter base this is normally acceptable – the holes only have to be inside the base region – but where an alignment between a perforation and something else is needed, it is not acceptable.
  3. The sheared edge is a burr. Every perforation has a burr on one face and a burnished edge on the other. On a filter this is a real problem: a burr protrudes into the flow path, catches fibres, and reduces the effective open area. Where the flow direction is known, the burr should face away from it – and that means the piercing direction has to be a specified decision.

Open area is a design number, not a consequence

The percentage of open area determines the filter’s pressure drop and its flow capacity, and it is directly determined by three things on the drawing:

  • Hole size. Larger holes mean higher open area and coarser filtration.
  • Hole pitch. Closer pitch means more holes in the same area and higher open area, but it also means less material between holes – and the web between holes has to survive the punching and the flow-induced vibration. A web that is too narrow is both a structural weakness and a filtration defect, because a deformed or cracked web changes the hole’s shape.
  • Hole shape. A slot has far less open area than a round hole of the same short dimension, which is why slot filters need more area for the same flow.

The design calculation is a balance: the filtration requirement sets the hole’s short dimension, the flow requirement sets the open area, and the two together fix the pitch. And then there is the strength check – a filter base sees flow-induced vibration and differential pressure across it, and a web that is too narrow will fatigue.

Burr direction and cleanability are functional requirements

On a filter cup, three requirements that are usually absent from the drawing and should not be:

  1. Which face the burrs are on. The burr faces the direction of the piercing punch’s entry. On a filter where flow enters from one side, the burr should be on the downstream side. This is a stated requirement, not a preference, and it is achievable because the piercing direction can be chosen.
  2. Deburring. A specified burr height rather than the word deburred. On a filter, a burr catches debris and defeats the cleaning process that a filter is supposed to survive.
  3. Cleanability in service. A perforated base will clog – that is what a filter does. Whether it can be cleaned, backflushed, or replaced depends on the hole’s shape and the burr condition, and on whether the perforations will pass the cleaning method being used. A very fine perforated filter that cannot be cleaned is a disposable part in a housing designed for a washable one, and that mismatch is worth catching at review.

The drawn cup, and what its form does to the function

The cup portion of the part has its own requirements, and they interact with the perforated base:

  • The base’s flatness determines how a gasket seats on it. A dished base will seal unevenly, which on a filter means bypass – flow going around the seal instead of through the filter, which is worse than no filter because it is not obvious.
  • The wall thickness at the base is where the draw’s thinning is most severe, because material flows into the base from the wall. So the base is the thinnest region of the cup, and it is also where the perforations are cut and where the thinning compounds. This is the most demanding zone on the part and it deserves a specified wall rather than a general tolerance.
  • The rim or flange is where the cup seats in its housing, and it carries the pressure the filter is supposed to hold. Its flatness and its position relative to the perforated base determine whether the filter is compressed evenly.
  • Any drain or outlet in the base is a functional feature and needs a defined open area, and it interacts with the perforation pattern’s flow distribution – a filter with one outlet hole in a large perforated base will have uneven flow across the base.

A filter cup in water or air is a 304 decision

Stock covers carbon steel in SPCC and DC01 grades, 304 and 316 stainless steel, aluminium and brass, with special grades sourced to the drawing when volumes justify. For a filter:

  • 304 stainless steel is the standard for water, air and general service filtration. It is cleanable, corrosion-resistant and food-service appropriate.
  • 316 stainless steel where the filtered medium is aggressive – solvents, salt water, acidic fluids, or a pharmaceutical process.
  • Aluminium for a light filter or where a fine perforation pattern is wanted – aluminium is softer and machines cleanly, so a fine perforation is easier on it. It is also more prone to deformation.
  • Brass where a fine pattern, a corrosion requirement, or a specific fluid compatibility applies.

Finish is selected from the drawing with masking and laser marking available. Three points here: passivation is standard for stainless steel and adds nothing dimensionally, which matters on a part with a perforated base where coating would alter the flow area; a coating must not build up in the perforations, because a plated or coated hole is effectively smaller and the filter’s rating changes; and where the filter carries a pressure boundary, the perforated base is not that boundary – it is the flange and the wall that seal.

A filter has two specifications, so its drawing list is twice as long

Eight things, and this is one of the longest lists in the family because the part has two specifications rather than one:

  1. Hole shape – round or slotted – with the slot orientation if slotted, since alternating orientation is what makes a slot filter work.
  2. Hole dimensions: short dimension (and long dimension for slots), with tolerances.
  3. Pitch and open area percentage, both stated, because both are design numbers.
  4. Which face the burrs are on, and the burr height requirement.
  5. Base flatness, against a named surface, because the gasket seats on it.
  6. Wall thickness at the perforated base, stated specifically since that is the thinnest and most stressed region.
  7. The flow direction – which way the filtered fluid enters and leaves – because it decides the burr direction and the outlet’s position.
  8. The filtration rating as a requirement, not just as a hole size. “Filters to 40 microns” is a verifiable statement; a hole diameter is a geometric statement that does not guarantee it.

And the question worth asking at review: is perforation the right filtration method for this requirement. Perforation is coarse – a punched hole has to be at least tens of microns across to be practical, and this process is realistically in the hundreds of microns. If the required filtration is finer than that, a fine woven or mesh screen supported on a drawn perforated base is the correct construction and the drawn part should be specified as a screen support rather than as a filter. Getting this right at the design stage avoids ordering a very precisely perforated part that still cannot do its job.

Not sure whether to draw, machine or weld this geometry? The guide to deep drawn covers compares the three routes and shows where each one wins; the full Precision Deep Drawn Parts range is linked from the overview page.

Specifications

ItemCustom Stamped Stainless Steel Deep Drawn Filter Cup Perforated Bottom
BrandAUNOV
DesigningSend drawings, or send a sample to be measured – DFM notes are returned before any tooling is cut; the agreed version governs every later batch.
ToolingDies are maintained by stroke count, so tooling condition does not drift mid-order.
SamplesSamples are produced on the production tooling, so what you approve is what you get.
MaterialsStock covers carbon steel (SPCC / DC01), 304 / 316 stainless steel, aluminium and brass; special grades are sourced to the drawing when volumes justify.
Surface finishThe drawing selects the finish: plating, coating, anodising or passivation, with masking and laser marking available where needed.
ProcessingMulti-stage deep drawing with interstage annealing, trimmed and pierced in following dies; first articles verify the whole flow before the run is released.
EquipmentMechanical presses from 5 to 250 T and hydraulic presses 250-500 T, with in-line annealing furnaces, with in-house toolmaking to keep dies and fixtures maintained.
Tolerance+/-0.05 mm to +/-0.1 mm across the part, wall thickness held to print; GD&T per drawing, PPAP-style reports on request.
Delivery termsFOB, CIF or DDP per Incoterms 2020, payment by T/T, L/C at sight or D/P; sea or air freight is quoted to your door.

Frequently Asked Questions

Are the perforations punched before or after the cup is drawn?

After. Piercing the holes first lets the wall distort and the holes go out of round as the metal draws, so the cup is formed first and the perforations are punched while the part is supported. It costs a second operation, but it is what keeps the holes round and the wall at the print thickness.

What open area can a perforated filter cup achieve?

Open area is a design number, not a consequence – it is set by hole diameter, pitch, and pattern against the wall thickness the cup can carry. We work it backwards from the flow or filtration target so the percentage is real, not a catalogue maximum the wall cannot support.

Which stainless steel is used for a perforated filter cup?

A filter cup in water or air is usually 304, with 316 specified for chloride or chemical duty. The grade follows the fluid, and the perforations are deburred so they do not catch or shed – burr direction is a functional requirement, not a finish note.

How is burr direction controlled on a filter cup?

The punch and die are set so the burr faces the side the application can tolerate, and the hole edges are deburred or rolled as the print requires. On a filter the burr side decides whether particulate is trapped or released, so it is called out on the drawing and checked on the sample.

Request a Quote for This Part

Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).