Zinc-Plated Closed Cylinder Sensor Pill

Zinc-Plated Closed Cylinder Sensor Pill
Zinc-Plated Closed Cylinder Sensor Pill

A general temperature sensor housing is the page where the process has to be settled before the drawing exists, because the same drawn shape can be a tank probe, a pipe insertion probe, a bearing sensor, an ambient monitor, or a food probe – and the requirements on those are not variations of one requirement, they are different requirements.

So this page is about the four questions that decide which of those the part is, and about the specific case that trips up more installations than any other: how the part is installed.

Four questions, and they are not the questions the drawing starts with

  1. Where does the temperature live? In a liquid, in air, on a surface, or in a solid. This is not a detail. A probe in a liquid can be a closed tube and a pressure boundary. A probe in air has no pressure requirement at all, and its requirement is usually that it does not conduct heat away from what it is measuring. A surface-mounting probe has no immersion and needs a contact surface. A bearing sensor is embedded in a rotating assembly and the requirement is entirely different again.
  2. Is there pressure, and if so what pressure? A probe in a pressurised line is a pressure boundary and its wall is a calculation. A probe in an unpressurised vessel is not, and its wall is set by the thermal and mechanical requirements only.
  3. How is it installed, and will it be removed? The question on the next section, and it is the one most often skipped.
  4. What is it made of, and does anything come into contact with the process? In a food or a pharmaceutical application this adds a documented requirement that has nothing to do with engineering.

Installation, which is where most failures come from

A temperature sensor housing is installed into something that is already there – a pipe boss, a vessel nozzle, a hole in a tank wall, a mounting bracket – and that something constrains the probe in ways the probe’s drawing cannot fully control. Four cases.

The threaded insertion

The common case: the probe screws into a boss. Three things follow and all three are on the drawing.

  • The thread’s standard, because the boss belongs to the customer’s equipment and the probe has to match it. A probe specified with a thread that is not the customer’s standard is not a probe that fits.
  • Whether the thread seals. A tapered thread, a parallel thread with a bonded seal, or a compression face – and the choice determines whether the probe’s seal is at the thread or on a face, and whether the port can be reused.
  • And the installation torque, which is a design output not an instruction – the torque is what compresses the seal, and the hex or the wrench feature that transmits it has to be strong enough.

The welded insertion

Where the probe must not leak and cannot be removed, it is welded. Then the weld is in the pressure boundary, the grade’s weldability is a requirement, and the probe’s tip geometry has to suit the weld – because the weld’s heat will have disturbed the metal near the tip, and on a thin-wall probe that is the part that has to survive.

The surface mounting

Bolted, clipped, or bonded to a surface. Three requirements: flatness of the mounting face, a defined contact area, and a stated interface material. And the accuracy is a function of the mounting, not just the probe.

The insertion into a liquid, with no boss

A probe on a bracket or a drop-in arrangement, in a tank. Here the requirements are different again: the probe’s length has to reach into the liquid, its lead has to be protected, and its response is set by the liquid’s convection on the tip – which means the tip’s diameter and length are both accuracy parameters.

Surface mount or insertion, which is a decision not a dimension

There are two fundamentally different products in this category and they are frequently confused because the drawings look similar.

Surface-mountedInsertion
Temperature pathThrough the mounting surface and whatever is behind itDirect, through the probe’s own tip
Accuracy determined byThe mount and the interface materialThe tip’s geometry and the immersion depth
Pressure requirementUsually noneFrequently yes, and then the wall is a calculation
ResponseSet by the mount’s thermal massSet by the tip’s mass and the fluid’s convection
Failure modeThe mount loses contact and the reading driftsThe tip’s wall corrodes or the seal weeps

So the first item on this part’s enquiry is which of the two it is, and the answer changes the material, the wall, the tolerance priorities, the process route and the price.

Material, and the specific case of the ambient or air-mounted probe

Materials held include carbon steel, 304 and 316 stainless steel, aluminium and brass, with substitutions proposed only in writing. On a probe that is measuring air, the thermal logic inverts and it is worth spelling out because it produces counter-intuitive answers.

  • An air-temperature probe wants a small, thermally isolated tip. The measurement is of air, and a probe that conducts heat from its mounting point into the tip is measuring the mounting point. So on an ambient probe the stem should be thin and long, or the tip should be thermally isolated from the stem, and the housing’s job is to make sure that no significant heat path exists between the mounting and the sensing tip.
  • Which means the housing’s thermal isolation is a specification and it is not visible on a dimensioned drawing. It is the stem’s diameter, the stem’s length, the material, and whether the stem is solid or hollow. On a well-designed ambient probe the stem is a poor conductor relative to the tip’s exposure; on a badly designed one the stem is a fin and the probe reads the mounting temperature plus a few degrees.
  • Aluminium is a poor choice for an ambient probe’s stem because it conducts too well – it will conduct heat from the mount into the tip. So on an ambient probe the material is chosen for low conductivity, which is the opposite of the choice on every other probe on this site. That inversion is worth stating because it is exactly the kind of thing that gets a part designed by someone who assumed the usual rules apply.
  • 316L where corrosion matters, and the L grade if it will be welded.

On most housings the accuracy is set by installation, not by the part

+/-0.01 mm on thread pitch diameters and +/-0.05 mm on the drawn body. On a generic housing page the tight band correctly goes to the thread, and everything else is at a general band – because on most of the products in this category the accuracy is set by installation rather than by the part.

  • Thread, class and pitch diameter, gauged, and the sealing method stated.
  • Any sealing face, flatness and perpendicularity, where the probe seals on a face.
  • Concentricity of the bore to the thread axis, where a probe is inserted and located by a bore rather than by its tip’s contact.
  • And the things that are not dimensions: the immersion depth, the mounting face’s flatness, the thermal isolation between the mount and the tip, and the stated accuracy’s reference condition. On a part like this those four items are more consequential than any tolerance on the drawing.

Gauge the thread to the boss standard your customer actually uses

Capability checked on the first article before the run continues. On a generic housing the inspection plan follows the part’s job.

  • Thread gauging, on every part, to the standard the customer’s boss uses.
  • Sealing faces, where there is one.
  • A functional assembly check against a representative boss or bracket on a sample. On a part whose job is installation this is the only test that verifies the part fits anything.
  • A functional temperature check where the part is supplied with an element – a resistance or EMF check against the curve at a reference temperature.

Who owns the boss or bracket this probe goes into?

Where does this probe go, and who owns the thing it goes into? Two questions, and the second one is the one that is almost never asked and that causes most of the returns. If the customer’s boss or bracket is a known part – if they have a drawing for it, or a standard, or an existing probe that fits it – then this housing is drawn to fit an interface that exists and the whole design is constrained by it. If the mounting is undefined and the probe has to fit whatever is there, then the probe has to be as adaptable as possible, and that usually means a standard thread and a stated insertion range. These two answers produce completely different parts, and the difference is not cosmetic – it decides whether the part seals, whether it fits, and whether the customer’s installation instructions have to say anything special. And there is a third question worth asking on a generic housing page because it changes what the part is: is this a probe housing or a complete sensor? Because a housing is a component with a price and a lead time, and a complete sensor has an element, a calibration, a functional test, and an accuracy claim – and the second one has a shelf life that the first does not.

Our Sensor Housings range is where this part sits. The sensor housings pages carry the process notes, common materials and inspection points behind every product in the family.

Specifications

ItemZinc-Plated Closed Cylinder Sensor Pill
BrandAUNOV
DesigningMade to your 2D/3D drawings (PDF, DWG, STEP, IGS) – samples are reverse-measured into a controlled drawing; revisions are re-quoted once rather than silently absorbed.
ToolingDie design and toolmaking stay in house, so no tooling step is outsourced, and the die remains dedicated to your part.
SamplesSample parts arrive with a dimensional report and material certification.
MaterialsMaterials held include carbon steel, 304 / 316 stainless steel, aluminium and brass; material substitutes are proposed only with your written approval.
Surface finishSurface treatment matched to the duty: plating, coating or polishing; finish thickness and adhesion checked on the first article.
ProcessingDeep drawing on hydraulic presses, CNC-finished where tolerances tighten; in-process checks sit between stages, not only at the end.
EquipmentDeep drawing presses plus CNC turning centres for machined faces, with in-house toolmaking to keep dies and fixtures maintained.
Tolerance+/-0.01 mm on thread pitch diameters, +/-0.05 mm on drawn body; capability is checked on the first article before the run continues.
Delivery termsCIF or DDP, with FOB available, payment by T/T, L/C at sight or D/P; repeat orders reuse the approved first article.

Frequently Asked Questions

Why must the process be settled before the drawing exists?

Because the same drawn shape can be five different products with five different requirement sets, a tank probe, a pipe insertion probe, a bearing sensor, an ambient monitor and a food probe are not variations of one requirement, they are different requirements. So the first item on the enquiry is which one it is, and the answer changes the material, the wall, the tolerance priorities, the process route and the price.

Why is accuracy set by installation on most of these housings?

On a generic housing page the tight band correctly goes to the thread, at +/-0.01 mm on thread pitch diameters and +/-0.05 mm on the drawn body, and everything else is at a general band. That is because on most products here the accuracy is set by installation rather than by the part. If the mounting is undefined, the probe must be adaptable, which usually means a standard thread and a stated insertion range.

When is a probe welded rather than threaded?

Where the probe must not leak and cannot be removed, it is welded. Then the weld is in the pressure boundary, the grade’s weldability becomes a requirement, and the tip geometry has to suit the welding heat, which on a thin-wall probe is the part that must survive. Surface mount or insertion is a decision, not a dimension.

Who owns the boss or bracket this probe goes into?

That ownership decides the thread standard to gauge against, because a probe fitted to someone else’s equipment has to match the boss standard the customer actually uses. Materials held include carbon steel, 304 and 316 stainless steel, aluminium and brass, with substitutions proposed only in writing. Installed into a liquid with no boss, the length, lead protection and tip response change again.

Request a Quote for This Part

Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).