Stainless Steel Stepped Sensor Sleeve with Side Port

Stainless Steel Stepped Sensor Sleeve with Side Port
Stainless Steel Stepped Sensor Sleeve with Side Port

A sensor housing specified as brass and stainless steel at the same time is usually a housing that has two halves for a reason, and the reason is nearly always corrosion on the outside and something else on the inside. That is a deceptively ordinary design, and it has three specific consequences that a drawing organised by material rather than by surface will miss.

Drawn on hydraulic presses and CNC-finished where tolerances tighten, at +/-0.01 mm on sealing faces and +/-0.05 mm on drawn profiles. So the split between the machined and the drawn is already visible in the tolerance scheme, and the split between the two materials is a third structure on top of it.

Why the two materials, and which surface each one is for

Carbon steel, 304 and 316 stainless steel, aluminium and brass, with the final grade fixed at the drawing review. On a two-material housing the material question is not “which alloy” but “which surface”.

  • The process side and the instrument side are different environments. The outside of a sensor housing sees the ambient – air, moisture, salt, a cleaning regime, a washdown. The inside sees the sensing element, the fill, and whatever is in the cavity. Those two environments are rarely the same, and a housing that has to survive both is naturally two materials.
  • The common arrangement: a stainless steel or brass outer body for mechanical and environmental duty, with a stainless steel or brass insert or liner that the process sees, or the reverse on a probe where the process side must be a specific alloy and the mounting side must be a machinable one.
  • And the boundary between them is a joint. Two materials means a joint – a weld, a brazed seam, a press fit, a threaded interface, or a drawn-over insert. That joint has its own failure modes and its own specification, and it is the part of this design that deserves the most attention, because it is the one place where the two halves meet and the one place where corrosion and stress concentrate.

The joint between the two materials, which is the whole design

This is where a two-material sensor housing is actually decided, and there are three ways to do it and they are not equivalent.

  1. Welded. A drawn shell with a drawn or machined closure welded on. Strong, hermetic if the weld is right, and it puts a weld in the pressure or seal boundary. On stainless steel the weld’s heat-affected zone is the metallurgical weak point and the L grade is the answer.
  2. Brazed. A high-temperature joinery, and on a sensor housing it is used where a lower-temperature solder would not survive the service. The brazed filler’s own properties matter and the joint’s temperature limit is the limit of the whole housing.
  3. Mechanical – press fit, thread, or a rolled-over insert. No metallurgical joint and no corrosion risk at the interface, but it is a leak path unless it is sealed, and on a sensor housing that is a pressure or a seal path, so it usually needs an O-ring anyway. The mechanical joint’s advantage is that it is inspectable and reversible, which matters when the housing has to be assembled around an element that cannot be welded near.

So the honest question on this part is: why two materials? And the answer should be on the drawing, because the answer decides the joint, and the joint decides whether the housing is hermetic, and that decides whether the sensor needs a vent.

Corrosion, and the galvanic couple at the boundary

Two dissimilar metals in contact, with moisture present, is a galvanic couple – and on a two-material housing the couple is not incidental, it is designed. But the design has to know which member is meant to corrode, and that has to be deliberate.

  • At a drawn-over or pressed-in stainless steel insert in a brass body, the brass is the less noble of the two and it corrodes preferentially at the interface – particularly if the crevice between them can hold moisture, which on a sensor housing it can. That is acceptable if the brass is thick at that point and unacceptable if it is not.
  • At a welded joint between two grades, the corrosion risk is different – it is the heat-affected zone, and it is solved by the grade rather than by the pairing.
  • And on the external surface, a brass housing in a salt-laden environment dezincifies, which is a slow loss of section and a loss of strength at exactly the mounting point. So a brass exterior is a time-limited choice and the wall’s thickness at the mount is the thing that determines the service life.

Why brass and why stainless steel, in a drawn sensor housing

Both are in the material list, and the honest reason each one appears is worth stating because they are not interchangeable on a sensor.

  • Brass is chosen for: machinability to a fine detail – a small sensor housing’s seal gland, a stepped bore, a thread – and for a plating-ready surface. Brass machines to a finer detail than stainless steel and holds it, and on a small housing with several close features that is the deciding property. Brass is also conductive, which matters if the housing is an electrical shield or a ground.
  • Stainless Steel is chosen for: the process side – corrosion resistance to whatever the sensor is in, at whatever temperature. 316L for chloride-bearing and cleaning regimes, 304 for benign service.
  • And on a sensor the thermal conductivity is a third reason, which is rarely stated. Brass conducts about six times better than stainless steel. On a fast-response sensor that difference is the response time. So on a sensor housing the material is a thermal decision as much as a corrosion one, and that is the item most often left unexamined.

Deep drawing a brass or a stainless steel sensor shell

Drawn on hydraulic presses with CNC finishing where tolerances tighten. On this part the drawing has two specific consequences.

  • The wall’s uniformity is the sensor’s accuracy. A drawn shell’s wall varies – it is the blank’s thickness plus the drawing’s stretch minus the corner’s compression. On a sensor housing that variation is a variation in the thermal path and therefore a variation in the reading. So the wall’s uniformity is a functional requirement and it belongs on the drawing as a uniformity statement rather than as a nominal wall.
  • The closed end is thinner and it is the thinnest part of the boundary. The punch nose stretched it. On a sensor housing the closed end is often the process-facing surface and the most thermally sensitive one, so a minimum wall there is a real specification.
  • Stainless Steel draws but work-hardens, so it needs a more generous blankholder force and it is harder on the tooling. Brass draws more easily and springs back more, so the open diameter after drawing will not match the die diameter – which is part of why the drawn profile’s tolerance band is looser than the machined band’s.

CNC finishing, and which features are worth it

The machined features on this part are the ones that seal, locate or thread, and the tight band on the sealing faces is where it belongs. The design question is which features those are, and the answer should minimise them.

  • Sealing faces – machined. Flatness and perpendicularity are the requirements, and they are the tightest band on the part.
  • Seal glands and stepped bores – machined. Because a gland’s compression is set by its depth and diameter, and a stepped bore positions the element.
  • Threads – machined, and masked from any finish.
  • And the outline, the wall, the general shape – drawn. These are consistent within the material’s own variation and drawing them is economical.

So the design discipline on this part is: machine the three or four features that have to be precise and draw everything else, and resist the temptation to machine a fifth because it is easier to reach.

Two materials and three surfaces means three finish jobs, not one

Natural, plated or coated – the print decides, and the agreed finish is logged, with masking and laser marking available. On a two-material sensor housing the finish has three different jobs on three different surfaces.

  • The sealing face, unmasked. It is a seal.
  • The external surface, finished conventionally – a plating for appearance and for corrosion, or a passivation on stainless steel. And on a two-material housing the finish on the brass member and the finish on the stainless steel member are different processes with different dimensional effects, which the drawing has to distinguish.
  • The process side, where it is a product surface in a food, pharmaceutical or medical application – its own documented finish requirement, its own passivation record.
  • And where the finish is doing a galvanic-isolation job – on the member that is meant to be the sacrificial one, or on the member that is meant to be isolated – then the finish’s thickness and its continuity are functional requirements and the adhesion test is not a formality.

Name which surface each material sits on, and how they are joined

  1. Which surface each material is on – the process side, the ambient side, or a specific face. This one sentence decides the joint and most of the corrosion questions.
  2. How the two materials are joined – welded, brazed, pressed, or threaded – and if welded or brazed, the process and the joint’s own specification.
  3. Whether the housing is hermetic, and if not, where the vent path is. A sealed sensor housing needs one; this is the question that gets forgotten.
  4. The wall’s nominal thickness and its minimum at the closed end, and the wall’s uniformity as a stated requirement.
  5. The sealing face’s flatness and perpendicularity against a named datum.
  6. Which features are machined and which are drawn, so the tolerance scheme’s two bands are explained rather than arbitrary.
  7. The masking list, by location, and the dimensions stated before or after finish.
  8. The fluid, its temperature, and its chemistry, as the reason for the material on the process side.

Which of the two materials is meant to see the process?

Why are there two materials on this housing – and which one is meant to see the process? That question is the one the drawing usually does not answer, and everything else follows from it. If the answer is “the process side is stainless steel because the fluid is corrosive and the ambient side is brass because it machines nicely and takes a plating”, then the joint, the corrosion behaviour, the thermal performance and the finish are all determined, and the drawing can be written properly. If the answer turns out to be “two metals because a standard part existed in both”, then the design has an unresolved corrosion couple and a thermal path nobody chose, and it is worth resolving before the part is quoted. And there is a question that is nearly always missed on a two-material sensor housing: is the housing hermetic? Because if it is sealed and there is no vent path, then as the temperature changes the internal pressure changes and the reading changes – a slow drift with temperature that will be blamed on the sensor. One question about the materials and one about the seal, and they are the two that turn a two-material housing from a specification into a design.

This part belongs to our Sensor Housings range. The sensor housings pages collect the process notes, common materials and inspection points behind every product in the family.

Specifications

ItemStainless Steel Stepped Sensor Sleeve with Side Port
BrandAUNOV
DesigningYour 2D/3D files (PDF, DWG, STEP, IGS) are reviewed for manufacturability before any price is confirmed.
ToolingDies, fixtures and gauges are made in our own toolroom, so tooling lead time stays under our control, and maintenance is tracked against the part number.
SamplesPre-production samples come with a full inspection report, so the approved first article becomes the gauge reference, and mass production is gated on that approval.
MaterialsStock runs to carbon steel, 304 / 316 stainless steel, aluminium and brass; the final grade is fixed with the drawing review.
Surface finishNatural, plated or coated – the print decides, and the agreed finish is logged; masking and laser marking available where needed.
ProcessingDeep drawing on hydraulic presses, CNC-finished where tolerances tighten; in-process checks sit between stages, not only at the end.
EquipmentHydraulic drawing presses and CNC lathes for sealing faces, with in-house toolmaking to keep dies and fixtures maintained.
Tolerance+/-0.01 mm on sealing faces, +/-0.05 mm on drawn profiles; dimensional reports accompany the first article.
Delivery termsCIF or DDP, with FOB available, T/T with deposit and L/C for larger runs; repeat orders reuse the approved first article.

Frequently Asked Questions

Why would a sensor housing be specified in brass and stainless steel at once?

Usually because the housing has two halves for a reason: corrosion on the outside and something else on the inside. One common split is a stainless steel process side for a corrosive fluid and a brass ambient side that machines nicely and takes a plating. That single decision fixes the joint, the corrosion behaviour, the thermal performance and the finish together.

What does the joint between the two materials decide?

The joint decides whether the housing is hermetic, and that in turn decides whether the sensor needs a vent. If it is sealed with no vent path, then as temperature changes the internal pressure changes and the reading drifts, a slow error that gets blamed on the sensor. So the drawing has to say which material sits on which surface and how they are joined; otherwise whether the housing ever needs a vent is left unanswered.

How does the tolerance scheme reveal which features are machined versus drawn?

The part is drawn on hydraulic presses and CNC-finished where tolerances tighten, at +/-0.01 mm on sealing faces and +/-0.05 mm on drawn profiles. The machined features are the ones that seal, locate or thread, and that tight band on the sealing faces is exactly where it belongs. The split between machined and drawn is already visible in the numbers, with the two materials forming a third structure on top.

Which of the two materials is meant to see the process fluid?

That answer belongs on the drawing, because it drives the joint, the corrosion behaviour and the thermal path. Two materials and three surfaces mean three finish jobs, not one, so naming each surface’s material is what makes the design buildable. The stock list spans carbon steel, 304 and 316 stainless steel, aluminium and brass, with the final grade fixed at drawing review.

Request a Quote for This Part

Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).