
This is a tall drawn can for a temperature sensor, mounted by a flange, and its two defining features work together. The small bore at the top is where the sensor passes through and is retained; the tall body is what keeps the process away from everything above the flange. The part is a barrier with a hole in the top of it.
The small top bore is the feature that is easy to get wrong
The top bore has to pass the sensor and then retain it, which makes it a clearance and a sealing fit at the same time. Too loose and the sensor rattles and the entry leaks; too tight and the sensor will not go in, or goes in and is scored by the edge. Because the bore is at the top of a deep can, it is also the feature most likely to be out of concentricity with the body – a bore that is correct in diameter but off to one side puts the sensor against the wall instead of down the middle.
A tall can protects what sits above the flange
The height is not arbitrary. A tall body puts distance between the process and the head, the cable and the transmitter, which keeps heat, splash and vapour away from the parts that are less able to tolerate them. It also gives the sensor a longer length over which to be guided, so a probe that would be unsupported in a short pocket is held along its length here.
The flange carries the seal and the fixing together
Mounting this by a flange rather than a thread means the can has to be removed without rotating it, which is the point: a tall can with a cable attached usually cannot be unscrewed. The flange is clamped against a gasket, so its face has to stay flat under bolt load, and the bolt pattern has to clamp evenly or the joint seals at the bolts and weeps between them.
Drawn in one piece, because a joint here would be the failure
This shape – tall, closed at the bottom, pierced at the top – is a natural deep draw, and drawing it as one piece removes the seam that would otherwise run down a welded construction. In a part that exists to separate a process from the equipment above it, the absence of a joint is the specification, and it is also what lets the can be thin: there is no weld to require extra thickness for the heat of welding.
How the can is checked before it ships
The top bore is measured for size and for concentricity with the body, the flange face is checked for flatness, and the closure at the bottom is inspected.
First articles and retention samples are kept for the programme, so a reorder is drawn to the same bore, the same height and the same flange geometry. On a part that is a barrier with a hole in it, that is what keeps the second batch sealing like the first.
This part sits inside our Sensor Housings range. Across the sensor housings pages you will find the process notes, common materials and inspection points behind every product in the family.
Where this part is used
Tall sensor cans with a small top bore mount by a flange into process piping, vessels and food equipment, and they are used wherever the sensing element has to sit in the medium while the electronics stay outside it. Temperature and pressure sensors in chemical, food and dairy plants are the common users, along with HVAC immersion sensors where the flange bolts to a duct or a vessel wall.
The two defining features work together rather than independently: the small bore at the top is where the sensor passes through and is retained, and the tall body is what keeps the process away from everything above the flange. Drawing the can in one piece matters because a joint at that height would be the failure point.
What we need to quote it
Send the process medium with its temperature and pressure, the flange standard or dimensions, and the sensor element dimensions that set the top bore. Tell us whether the can is welded or filled downstream, and whether the flange is a sealing face or only a mounting face — that single answer changes the flatness we have to hold.
Specifications
| Item | Stainless Steel Tall Sensor Can with Small Top Bore |
|---|---|
| Brand | AUNOV |
| Designing | Quotation follows the print, not a catalogue – samples are reverse-measured into a controlled drawing; the approved drawing is kept as the controlled master. |
| Tooling | Our toolroom covers die design, wire-cut EDM and maintenance, so tooling lead time stays under our control, and the die remains dedicated to your part. |
| Samples | Free samples are available on standard items, with reports attached. |
| Materials | Materials held include carbon steel, 304 / 316 stainless steel, aluminium and brass; the final grade is fixed with the drawing review. |
| Surface finish | Surface treatment matched to the duty: plating, coating or polishing; the finish is inspected with the dimensional report on the first article. |
| Processing | Blanking, drawing and piercing in sequence, then machining of sealing faces; every stage is logged against your part number. |
| Equipment | Deep drawing presses plus CNC turning centres for machined faces, with CNC turning centres for secondary operations and CMM inspection. |
| Tolerance | +/-0.01 mm on turned or milled features, +/-0.03 mm on formed details; critical dimensions carry CMM data with the shipment. |
| Delivery terms | FOB with DDP offered for EU and US addresses; payment T/T or L/C, freight quoted to destination. |
Related Products
Frequently Asked Questions
Why is the small top bore the feature most likely to be got wrong?
The top bore has to pass the sensor and then hold it, so the same opening is asked to be a clearance and a seal at once. Because it sits at the top of a deep can, it is also the feature most likely to be off-centre from the body. The bore is measured for size and for concentricity with the body, and the flange face for flatness, on the first article.
Why mount a tall can by a flange rather than a thread?
A tall can with a cable attached usually cannot be unscrewed, so it has to be removable without being rotated. The flange is clamped against a gasket, which means its face must stay flat under bolt load, and the bolt pattern has to clamp evenly or the joint weeps between the bolts. Send the flange standard or dimensions along with the process conditions when you enquire.
Why draw this can in one piece instead of welding it?
This tall, bottom-closed, top-pierced shape is a natural deep draw, and drawing it as one piece removes the seam a welded construction would carry down its length. In a part that exists to separate the process from the equipment above it, the absence of a joint is the specification. It is also what lets the can be thin, because no weld demands extra thickness for welding heat.
What is checked before a tall sensor can ships?
The top bore is measured for size and concentricity with the body, the flange face for flatness, and the bottom closure by inspection. First articles and retention samples are kept for the programme, so a reorder is drawn to the same bore, the same height and the same flange geometry. Tall cans with a small top bore mount into process piping, vessels and food equipment.
Request a Quote for This Part
Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).




