
An anodised aluminium frame has a problem that a plated or painted frame does not have, and it is worth naming before going further: anodising improves corrosion resistance and appearance and makes the part marginally stronger and marginally harder, and it simultaneously turns the surface into a thermal insulator and a slightly thicker, slightly rougher, slightly dimensionally changed material. Most of the design decisions on this part come from that trade.
A frame is a structure first. It has to hold something in position, resist whatever load the assembly puts through it, and do that for years without the joints loosening or the corners moving. Anodising touches all three of those in ways that are easy to miss.
Why anodise a structural aluminium frame
The reasons are real, and they are worth listing precisely because the side effects only make sense against them.
- Corrosion resistance. The oxide layer is the same chromium-oxide-rich layer that makes stainless steel corrosion-resistant, and on aluminium it is genuinely protective. Uncoated aluminium develops a white oxide and loses appearance within a season outdoors; anodised aluminium does not.
- Appearance and consistency. Anodising takes colour into the surface rather than onto it, so it does not chip at edges the way a coating can, and it is more uniform than powder coating on a complex three-dimensional part.
- Surface hardness. A hard anodise with a heavier oxide is measurably more wear resistant, which matters on a frame that gets handled, slid into place, or has moving parts that rub on it.
- Galvanic isolation from fasteners. This is the quiet one. Aluminium in contact with a steel or stainless steel fastener will corrode galvanically at the contact point, and anodising makes the aluminium surface slightly more insulating, which slows this. It does not eliminate it, which is why the design question is still about isolating the fasteners rather than about the anodising.
The thermal consequence, and it is the one that surprises people
Aluminium conducts heat very well through the bulk. The oxide layer on it conducts very badly. The thermal path across an anodised mounting face is therefore dominated by the anodised layer, not by the aluminium behind it.
This matters whenever a frame is meant to carry heat away from something mounted to it – an electronics assembly, a power device, a motor mount. On a bare machined aluminium face, the contact area can carry heat well. On an anodised face, the same contact area carries noticeably less, because the heat has to get through a layer with roughly an order of magnitude less conductivity than the metal underneath it. The improvement in corrosion resistance has been paid for with a real thermal penalty.
There are three standard ways to manage this, and the choice belongs on the drawing rather than in the assembly manual:
- Mask the mounting face. Leave the anodising off the areas that make thermal contact. This is the cleanest answer and it is the one most often forgotten, because the face that matters thermally is usually an internal face nobody thinks to look at.
- Use a thermally conductive interface material. A gap filler or a thermal pad is designed to bridge a low-conductivity layer, and it does it well – but only if it is specified to a thickness and a conductivity, and only if the anodised surface is flat enough for the pad to make contact over its area rather than bridging the highest points.
- Move the thermal path off the frame. If the frame is primarily structural, a separate thermal interface – a boss, a pad, a dedicated heat spreader – can do the heat transfer and the frame can be anodised freely. This is often the right answer when the frame’s structural job and its thermal job are genuinely separate.
On a frame that is purely structural, none of this matters and the anodising should simply be left everywhere and kept off the moving or mating surfaces. The useful thing is to establish which kind of frame it is before the finish is written, because the two need different mask lists.
The dimensional consequence
Anodising is an electrochemical process that converts aluminium at the surface into oxide. The metal does not simply get coated; it grows outward, and the growth consumes part of the underlying metal. The dimensional result is a surface that moves outward by a predictable but not-negligible amount, and the movement is largest where the current density was highest.
For a frame, the items that this affects are the ones where a few microns matters or a few tens of microns matters:
- Holes that take a fastener. Anodising reduces the effective clearance. On a clearance hole this is beneficial – it tightens the joint slightly – but if the hole is close to its limit it can become a press fit and the fastener will not seat flat.
- Mating faces between frame components. If two anodised faces meet, the joint now has two insulating layers in series and the joint is no longer electrically continuous. For a frame that has to be electrically bonded, this matters.
- Anything that slides or rotates on the frame. An anodised surface is harder and rougher than bare machined aluminium, and it will change the wear behaviour of anything running against it.
- Press or interference fits. If a component is meant to press into the frame, the anodised layer has to be accounted for in the interference, and the roughness of an anodised surface means the effective interference is less predictable than a machined one.
The clean specification practice is the same as for any finished part: state whether dimensions are before or after finishing, give the anodising class and the coating thickness range, and list the masked areas by name and by location. A frame with an anodising callout and no mask list will come back with anodising everywhere, and then some of those places will need to be machined after finishing, which is both ugly and expensive.
Anodising classes, and which one this frame probably is
The three classes are worth distinguishing because the specification is written in class terms.
- Decorative or colour anodising, typically to 5 to 15 microns, organised on appearance. It is a thin oxide, it is dyed, and it does not significantly change the surface’s functional behaviour. This is the right choice for a frame that is purely structural and visible.
- Hard or wear-resistant anodising, typically to 25 to 60 microns, on a hard alloy. This gives real wear resistance and a considerably thicker layer, which means a much larger dimensional change and a much more visible surface texture. It is also more expensive and it is what you choose for a surface that will be rubbed against or handled in service.
- Conversion coatings – chromate, phosphate, passivation – that are thinner and that exist mainly for conductivity or corrosion rather than for appearance.
On a frame, hard anodising is worth considering wherever the surface is a wear surface, and worth avoiding wherever the frame carries a tight tolerance. It is a common mistake to specify hard anodising on a frame for appearance, because it looks different and costs more, and then to discover that its dimensional effect has to be accommodated at a joint.
Structure, which is the part’s actual job
Since this is a structural frame, the geometry questions are the ordinary structural ones, and they are worth stating because they get lost behind the finishing discussion.
The load path on a frame is almost always through joints rather than through sections. A milled or folded aluminium frame fails at the corner where two members meet, or at the bolt hole where the local bearing stress is highest, or by flexing under load until a joint works loose. Three things drive all three of those:
- Where the members are thickest relative to the load. A frame’s stiffness is dominated by the section’s second moment of area, and a member that is deeper in the direction of the load is worth several times one that is merely wider. This is the cheapest stiffness available on a frame.
- Corner construction. A welded or brazed aluminium corner with a fillet is stronger than a bolted corner with the same members, because the fillet acts as a gusset. On a frame where strength matters, the corners are usually the place to put the metal.
- Joint stiffness, not joint strength. Two aluminium members bolted together with a clearance fit will slide a small amount before the bolt bears. That slide is a lost length in the structure and it is why frames that feel sloppy under load are not necessarily weak – they are loose. Closing the clearance, using shoulder bolts, or using bonded joints changes the stiffness more than any section increase would.
None of this is visible in a finishing specification, which is why the finishing discussion tends to crowd out the structure. Worth keeping both in view.
Tolerance, allocated to the structure
+/-0.02 mm general machining with tighter bands on flagged dimensions is a reasonable framework, and on this frame the flagged dimensions should be:
- Bore and mounting-hole positions relative to the frame’s datum surfaces, held tightly enough that the frame assembles without shimming. On a frame, position errors accumulate around a loop and the worst one closes the assembly.
- Any bore that receives a pivot, a hinge, or a shaft, on both size and roundness, because this is what the frame’s accuracy actually depends on if it is a mechanism frame.
- Flatness of the mounting pads, where the frame attaches to a base or to a housing.
- The position of the thermal interface surfaces, if the frame carries heat, to the same order as the parts mounting to them.
- General member dimensions at a general band. On a frame these do almost no functional work.
Anodising thickness varies with current, so state where you measured
- Coating thickness and adhesion on the first article, with the measurement location stated, because anodising varies with current distribution across a complex part.
- Masked areas verified, not assumed. A frame with four masked pads should have all four checked.
- Flatness and position after finishing, not before. This is the single most common reason an anodised frame arrives at assembly and does not fit.
- Colour against an approved retained sample, with the light source stated. Anodised colour is not stable across different bath chemistry and different operators, and a reference sample is the only workable standard.
- Thread condition, if any threads are masked out or machined after finishing.
- Assembly check on the first article, which on a frame is the most informative inspection of all. If the frame goes together with a known torque and no shimming, the tolerances are right.
Anodised everywhere, or masked where it mounts
Does the frame need to be anodised where it mounts things, or would a machined bare or chromate-converted surface do the job at the mounting points? On most frames, the answer is that only a small fraction of the frame’s surface needs the anodising’s corrosion protection – the exposed exterior does – and the mounting surfaces are better left as machined metal, or masked and finished separately. Splitting the finish specification into “anodise the visible exterior, mask the mounting and joint faces” is usually both better-performing and cheaper than a single blanket anodise callout, and it removes the thermal penalty almost entirely. Establishing the split before the drawing is released is easier than recovering it afterwards, because a masked region that has already been anodised has to be machined back, and machining back an anodised surface means you have lost the dimensional control you paid for in that region.
CNC Machining Parts is the parent range for parts like this one; the overview page gathers the tooling logic, finishing options and tolerance notes that apply across the family.
Specifications
| Item | Anodized Aluminum CNC Machined Enclosure Frame |
|---|---|
| Brand | AUNOV |
| Designing | Your drawing sets the part – unusual walls, threads or tolerances are feasibility-checked first; the agreed version governs every later batch. |
| Tooling | Die design and toolmaking stay in house, so the die charge appears as its own quotation line, and maintenance is tracked against the part number. |
| Samples | Sample and first article are the same discipline here: measured, reported, then approved. |
| Materials | Stock runs to carbon steel, 304 / 316 stainless steel, aluminium and brass; the final grade is fixed with the drawing review. |
| Surface finish | Surface treatment matched to the duty: plating, coating or polishing; finish thickness and adhesion checked on the first article. |
| Processing | CNC turning with milling and drilling in as few setups as the geometry allows; every stage is logged against your part number. |
| Equipment | 12 CNC turning centres with automatic bar feeders; first articles and batch samples are checked on the CMM. |
| Tolerance | +/-0.02 mm general machining, tighter on flagged dimensions; dimensional reports accompany the first article. |
| Delivery terms | FOB Ningbo or Shanghai, T/T with deposit and L/C for larger runs; price breaks tie to annual volume. |
Related Products
Request a Quote for This Part
Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).




