
What a rounded lip does that a plain flange edge cannot
A flange ring with a rounded lip looks like a small refinement over a square-cut edge, and in most assemblies it is the difference between a part that works for years and one that damages everything it touches. A curled lip turns the raw cut edge back into the part, so the sharp edge that would abrade a hose, cut a wire jacket or saw through a gasket disappears. On rings that carry a clamped hose or flexible boot, the lip is the retention feature: the clamp bears against a rounded bead that grips without biting, and the joint’s pull-off force is set by lip diameter and radius, not clamp torque alone. On rings that mate with a seal, the lip keeps the gasket in compression against a controlled radius instead of letting it creep over a knife edge.
In our process the lip is formed deliberately, in its own operation, from a flange left with the right amount of stand-up metal. The drawing specifies the finished lip as a rolled profile with outside diameter, lip radius and finished flange thickness – “break all sharp edges” is not a lip, and we will not fake one with a chamfer unless the assembly genuinely only needs a deburr.
Curling the lip: tool progression and the thinning limit at the curl
A curl is a demanding forming operation masquerading as a simple one. The edge metal bends through roughly 180 degrees – sometimes more, into a full bead – and the outer fibers see the highest strain anywhere on the ring. Three limits govern it. The bend radius at the curl: for low-carbon steel we hold the inside radius at or above sheet thickness; below about one thickness the outer fiber strains past the material’s limit and the lip cracks lengthwise – a failure that hides under paint and appears only when the hose clamps down. Edge quality before curling: the curl starts at a trimmed edge, and any burr or micro-crack from the trim is a crack starter when the edge bends back on itself, so we deburr before curling as a rule. And the amount of stand-up metal: too little and the curl does not close; too much and the bead laps over itself and grows the flange diameter.
The tooling progresses in two or three steps on production volumes: a pre-curl that tips the edge up about 45 degrees, the closing roll that completes the bead against a shaped punch, and on thick or high-strength stock a coining step that sets the final radius. Each step’s geometry is recorded in the tool file because the split between pre-curl and close decides where the strain lands – a rushed single-step curl on 2 mm steel puts everything into the final bend and tears. For harder conditions – 304 stainless steel, or work-hardened carbon steel after several draws – the curl limit tightens, and we may need an interstage anneal on the flange or a larger curl radius, decided at the feasibility review rather than after the first cracked lot.
We measure the finished curl by sectioning first articles: one sacrificial ring per part number is cut radially and the curl profile compared against the tool profile under magnification, with outer-fiber thinning measured directly. The acceptance rule: the curl does not thin below about 80 percent of flange thickness and shows no cracking or orange peel at the outer fiber. Where a section cannot be spared, the lip is checked by profile gauge on the outside diameter and a controlled push test on the bead.
Bore-to-flange concentricity when the bore is pierced in-die
A flange ring has two functional features – bore and flange OD – and the assembly cares about their relationship. When the bore is pierced in the draw die, bore position is tied to the draw centerline and bore-to-wall runout holds within about 0.1 mm on a medium ring – good enough when the bore clears a shaft generously. But the flange OD is trimmed later, and if that trim is located off the drawn wall rather than off the bore, the runout stacks: the draw’s bore-to-wall eccentricity plus the trim’s wall-to-OD eccentricity land together on the finished part.
When the drawing demands better – a ring whose bore pilots on a shaft while the flange OD seals, or one carrying a rotating component – the route changes. We pierce or machine the bore in the final operation, located from the trimmed OD, or machine both the bore and a flange locating diameter in one CNC turning setup, which holds concentricity to around 0.03 mm and bore size itself to machining tolerance. The cost trade is explicit: piercing in-die is nearly free per piece and pays for the extra die section; machining adds a turning operation per part and saves nothing on tooling. Above roughly ten thousand pieces a year the in-die route with a well-located trim usually wins; below that, or above a 0.05 mm runout requirement, machining wins on scrap rate alone. A third route sits between: a sizing punch pushed through the pierced bore irons the wall, improving size and roundness while leaving the bore harder and smoother – one fast operation, no chip stream – which matters when a shaft runs directly in the bore or an O-ring seals against it.
Flange flatness after trimming: the last operation can undo the earlier ones
Flatness is the flange’s signature characteristic, and it is won and lost at the end of the route. A drawn flange comes off the press with inherent dish or wave – the binder cannot perfectly restrain the flange metal, and residual stresses relax unevenly. Left alone, a flange on a 100 mm ring might sit 0.3 to 0.8 mm out of flat. The trim adds its own distortion: cutting force rolls a curl of stress into the rim, and on a flange under about 1.5 mm the trim alone can lift the edge 0.1 to 0.2 mm in lobes that follow the die’s segment layout.
Three tools fix flatness, in escalating cost. A restrike hits the ring between flat platens – quick, cheap, adequate down to about 0.15 to 0.2 mm on medium rings. A sized restrike with a flat anvil and shaped pressure pad holds the 0.1 mm class. Below that, when a gasket seat or bearing face demands 0.05 mm, the honest route is machining: face the flange in the same turning setup that bores the ring, so flatness, squareness of flange to bore, and finish come from one clamping and one tolerance chain. We specify which route the part needs at quotation, from the drawing’s flatness callout – the difference between a restrike and a machined face is a real cost line, and there is no sense paying for machining flatness on a ring that welds into a bracket. One distortion source trimming cannot fix is stress relief over time: a heavily drawn ring holds residual stress, and weeks later, or after oven heat in coating, the flange can walk. For rings headed for plating, e-coat or powder – all involving 150 to 200 °C bakes – we gauge flatness after coating, so acceptance data reflects the part your line receives.
Gasket seat duties carried by the flange face
When a flange ring seals, the gasket spec and the flange spec are one specification. A soft gasket – rubber, fiber, elastomer-bound – forgives perhaps 0.1 to 0.3 mm of flange flatness error depending on section and compression, and the flatness callout should come from the gasket supplier’s sealability data, not a default. A hard gasket – metal, semi-metallic, or a thin elastomer on a shallow bead – forgives almost nothing; flange flatness there belongs in the 0.05 mm class, which routes the part to a machined face.
Surface finish on the seat matters as much as flatness. A gasket seats against the as-drawn flange surface – around Ra 0.8 to 1.6 µm on low-carbon steel, usually fine for soft gaskets. The failure mode to avoid is a directional tool mark crossing the seal path: a deep oriented scratch across the gasket width becomes a leak path no clamp load will close. Drawn flanges rarely have them, but trimmed edges, handling damage and coating runs do – so acceptance for a sealing ring includes a visual seal-band condition, and coating is either masked off the seat or the seat is machined after coating.
How we verify lip geometry and flange flatness on flange rings
The release routine is written per part number and shared with you at first article:
- Flange flatness on a surface plate or CMM – first article on every piece, production on the agreed sampling plan. Acceptance within the drawing band, measured after the final operation including any coating bake.
- Bore size, roundness and concentricity to the flange OD – two-probe runout on a rotating table or a CMM relationship measurement, per the route: 0.1 mm class pierced, 0.03 mm class machined.
- Lip profile by radial section on a first-article ring, outer-fiber thinning against the 80 percent floor, no cracking; in production, lip OD by gauge plus a push-out test where the lip carries retention.
- Flange OD and thickness at a fixed pattern of stations, to catch trim die drift before it reaches the tolerance edge.
- Seal band condition – visual and tactile inspection of the gasket path for scratches, dents and coating defects, against a boundary sample.
- Edge condition – inner and outer burr check after trim and before curling, and a final burr check on any machined bore.
- Records: dimensional report at first article, mill certificate per heat, and the stage settings file – including pre-curl and curl tool geometry – archived under your part number so the reorder repeats the route exactly.
The engineering calls behind a part like this — draw ratio, wall thinning, radii and trim — each get worked examples in our deep drawn covers guide; the Precision Deep Drawn Parts pages gather the rest of the family.
Specifications
| Item | Steel Deep Drawn Flange Ring with Rounded Lip |
|---|---|
| Brand | AUNOV |
| Designing | Send the drawing, or a ring sample we can measure, you get a DFM review together with the quotation. |
| Tooling | Dies engineered and produced in our own toolroom, held and maintained under your part number. |
| Samples | Samples for approval come with a full dimensional report and material certification. |
| Materials | Stock for this part leads with carbon steel (SPCC / DC01), alongside 304 / 316 stainless steel, aluminium, brass and copper, per the drawing. |
| Surface finish | Plating, e-coat, powder coating, anodising or passivation as the drawing calls out, selected against the drawing requirement. |
| Processing | Staged deep drawing, with in-line annealing where the draw ratio requires, pierced and finish-machined on the same floor. |
| Equipment | Mechanical presses 5-250 T and hydraulic presses 250-500 T, CNC turning centres and a climate-controlled CMM room. |
| Tolerance | Drawn tolerances held to +/-0.1 mm, +/-0.03 mm after machining. |
| Delivery terms | Standard terms FOB, DDP offered to EU and US, T/T or L/C, D/P on repeat business, call-off scheduling supported. |
Frequently Asked Questions
What does a rounded lip do that a square edge cannot?
A curled lip turns the raw cut edge back into the part, removing the sharp edge that would abrade a hose, cut a wire jacket or saw a gasket. On a clamped hose the lip is the retention feature; on a sealed ring it keeps the gasket in compression against a controlled radius.
How is the lip formed without thinning past the limit?
The lip is formed in its own operation from a flange left with the right stand-up metal, so the curl is controlled rather than stretched thin. The drawing specifies the finished lip as a rolled profile with outside diameter, lip radius and finished flange thickness.
How is flange flatness held on a ring?
The flange is trimmed as the last operation because trim springback can undo earlier work, and flatness of the sealing face is checked after trimming. Bore-to-flange concentricity is held when the bore is pierced in-die.
How is a flange ring verified before shipping?
Lip geometry, flange flatness and concentricity are measured on the CMM, and the typical minimum order is 1,000 pieces with a 24-hour quotation.
Related Products
Request a Quote for This Part
Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).




