Oxygen Sensor Case – Exhaust Seal

Oxygen sensor case
Oxygen sensor case

Closing an oxygen sensor: the case that seals against exhaust

An oxygen sensor must be electrically sound, mechanically fixed and gas-tight – and the oxygen sensor case is the part that finishes the assembly around those three requirements. It closes the sensor’s body, carries the electrical connection’s entry, and seals against the exhaust environment where the sensor’s other end faces the harness. Its engineering is therefore about sealing and electrical integrity in a place where both are hard: high temperature, thermal cycling, engine vibration and the requirement that the sensor’s signal leaves the case uncorrupted.

The electrical entry: a seal that also insulates

The case’s electrical entry – where the sensor’s conductors leave toward the harness – must do two things at once: keep exhaust gas and moisture out, and keep the conductors electrically isolated from the metal case through the full temperature range. That combination is harder than either alone. Our cases carry the entry features as formed geometry – a stepped or counterbored opening whose depth and diameter set the seal’s compression – and we dimension those features as a pair with the seal or insulator the customer uses, exactly as on our terminal pages, so the compression is consistent rather than variable. Where the sensor’s architecture uses a ceramic insulator, its seating depth and bore are held to the insulator’s print. The verification is a pressure or helium leak check on first articles and on audit samples, because a seal that holds at assembly and relaxes at temperature is a failure that only a thermal-cycled leak test catches.

Sealing against the exhaust side

At its other end, the case meets the sensor’s body and the exhaust’s heat. This joint is usually mechanical – a crimp, a weld or a formed interlock – and it must hold gas-tight while cycling through hundreds of degrees. Our designs favour formed interlocks and crimps where the sensor’s architecture allows, because a formed joint has no filler to oxidise and no heat-affected zone to crack, and we validate the joint’s integrity by the method the customer’s specification calls for. Where the joint is welded, the case’s material matches the body’s so the weld’s metallurgy is sound, and the weld’s geometry is designed for full penetration without burn-through on the thin case wall – a balance that calls for the case’s wall thickness and edge preparation to be agreed with the customer’s joining process early.

Thermal cycling and the case’s dimensional life

A sensor case cycles thermally on every engine start and stop, and that cycling works on the case’s crimps and its electrical entry’s compression. A case whose sealing features were sized for assembly temperature can relax its seal as the materials’ expansions differ, and a crimp that loses its preload begins to leak. We size the case’s joints for the hot condition rather than the assembly condition – the classical mistake is designing at room temperature – and where the application is severe, the case is validated on a thermal cycling rig with leak checks at intervals. This is the discipline that separates a sensor case that lasts the vehicle’s life from one that leaks in year three.

Materials and finish for the sensor’s environment

Case materials follow the sensor’s position, as with the can: standard exhaust-grade stainless steel where temperatures are moderate, heat-resisting grades where they are not. Because the case often sits where the harness and connector are also exposed, the finish must resist external corrosion as well as exhaust-side heat, and the cut edges and the connector’s seating faces are where corrosion starts. We specify finishes rated for the sensor’s environment and pay attention to the entry’s geometry so water cannot pool around the seal. Where the case must also provide electrical continuity to the sensor’s ground, we define the conductive surfaces on the drawing and mask them during finishing, as on our other electrically active parts.

Sealing features sized for assembly temperature

The case drawing with the electrical entry’s geometry, the seal or insulator’s print, the joint to the body (crimp, weld or interlock) and the joining specification; the sensor’s exhaust position and peak temperature; the thermal cycling and leak requirements; the finish and electrical continuity spec; and volume. First articles in four to five weeks after die approval, with leak checks, joint integrity results and thermal cycling where specified.

Sensors leak at the case after a few years

Our sensors leak at the case after a few years – seal or geometry? Often the sealing features sized for assembly temperature, which relax as the case heats. We can check a returned case’s compression and propose a hot-condition fit.

Can you make the electrical entry a formed feature instead of an assembled one? Where the insulator’s print allows, yes – a formed seat is more consistent than a stacked one and eliminates assembly variation. We will review the insulator’s geometry with you.

Do you weld the case to the body? On qualifying volumes, yes – welded or crimped and leak-verified to your specification, with the sensor’s electrical parts installed by you or, if you prefer, assembled and verified by us.

Sensor Housings is the range this part sits under; the overview page pulls together the tooling logic, finishing options and tolerance notes that apply across the family.

Specifications

ItemOxygen sensor case
BrandAUNOV
DesigningSend drawings, or send a sample to be measured – DFM notes are returned before any tooling is cut; revisions are re-quoted once rather than silently absorbed.
ToolingOur toolroom covers die design, wire-cut EDM and maintenance, so no tooling step is outsourced, and maintenance is tracked against the part number.
SamplesPrototype and pre-production samples are provided against the drawing, so the sample is retained as the master, and mass production is gated on that approval.
MaterialsStandard stock: carbon steel (SPCC / DC01), 304 / 316 stainless steel, aluminium, brass; special grades are sourced to the drawing when volumes justify.
Surface finishFinish per the drawing: plating, coating, anodising or passivation, plus masking and laser marking where needed.
ProcessingDeep drawing on hydraulic presses, CNC-finished where tolerances tighten; in-process checks sit between stages, not only at the end.
EquipmentPress line for drawing, CNC cells for finishing; first articles and batch samples are checked on the CMM.
Tolerance+/-0.01 mm on turned or milled features, +/-0.03 mm on formed details; GD&T per drawing, PPAP-style reports on request.
Delivery termsFOB Ningbo or Shanghai, T/T or L/C, with D/P accepted on repeat business; each volume tier carries its own quoted price.

Frequently Asked Questions

What is the case actually required to do – close the sensor, or seal it?

Both, and they are separate requirements. Mechanically it retains the sensor against pressure and vibration. Electrically it must insulate, because the same structure that carries the gas side also carries the wiring side. Then it has to be gas-tight between the two. Those are three demands on one part, and treating them as one is precisely how a case passes inspection and still leaks.

Why is the electrical entry described as a seal and an insulator at the same time?

Because those two properties are being demanded from one location, and improving one usually compromises the other. What blocks gas is rarely what blocks current, and both have to work at operating temperature rather than at room temperature. Writing both requirements against the same feature prevents solving one and discovering the other later, which is otherwise the usual sequence.

Why does assembly temperature enter the sizing of a sealing feature?

The seal stack is made of several parts that expand at different rates. A seal line loaded correctly when cold can unload once hot, or become overloaded, depending on which member wins. Sizing the feature for the temperature at which it assembles, rather than for room temperature, is what keeps the seal loaded through the cycle, and that condition belongs on the drawing.

What shortens a case’s dimensional life – cycles or accumulated hours?

Cycles. A case spends its working life going up and down in temperature, and each excursion moves the sealing dimensions a little as the structure relaxes. Steady hours do comparatively little. Validation that simply holds temperature will therefore not predict how long the seal lasts, which is why cycling rather than soak testing is the honest check.

Request a Quote for This Part

Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).