
A stainless steel tall thin-wall cylinder tube is a long, slender drawn tube whose wall is a small fraction of its diameter – the geometry that gives it both its compliance and its vulnerability. Being tall and thin, its behaviour is dominated by stiffness and by how the wall holds dimension through handling, not by pressure alone. The draw has to keep the wall uniform end to end, because any variation shows up directly in the bore.
So this page is about adsorption and desorption, and about why a stainless steel tube is unusable for that purpose unless it has been lined – and about what the lining actually has to be.
What the tube’s interior is for
In a capillary system – gas chromatography, and the sampling and transfer lines around it – the analyte is a molecule at trace concentration travelling through a gas stream. It is carried to a detector. The tube it travels through is not a pipe; it is a surface that the analyte is in contact with for the whole journey.
- And a surface attracts molecules. A stainless steel surface is polar and it will adsorb polar analytes. The analyte that sticks to the wall is not measured – it is simply delayed, and delayed differently depending on how much wall the sample touched and for how long.
- The consequences are specific and they are the whole problem on this page: peak broadening, because the analyte comes off the wall over a long tail; peak splitting, where a sample injected in two slugs leaves in two slugs; and quantitative error, where a heavy analyte is lost more than a light one and the calibration no longer describes the samples.
- Which means the tube’s material is not a mechanical choice at all. It is an analytical choice, and it is made before anyone thinks about pressure or temperature.
Why stainless steel is the wrong answer and lining is the right one
- Deactivated or lined stainless steel is the industry answer, and the lining is what makes it work. A thin layer of an inert polymer – a fused-silica coating, a polyimide or PTFE-type layer, or a passivation treatment that reduces the surface’s polarity – covers the metal and provides the inert surface the analyte needs.
- The lining has to survive the whole duty. On a GC column the temperature goes to several hundred degrees and the pressure is moderate; on a sampling line the temperature is lower and the pressure higher. So the lining’s temperature limit and its pressure limit both matter, and a lining that is inert but will not survive the temperature is the same as no lining.
- And a lining is a wear item. It is a thin layer on a tube that is going to be bent, connected, and possibly abraded by the fittings. Where it is scratched or chipped, the exposed stainless steel is back, and it will adsorb. So a lined tube’s performance degrades with handling, and that is worth telling the customer.
What this means for the mechanical design
This is where the analytical requirement meets the mechanical one, and on a lined tube there are three places where they interact.
- Every cut end must be lined, or the cut edge is exposed stainless steel inside the flow path. A tube cut for length has a raw edge, and on a lined tube that edge is bare metal sitting directly in the gas stream. So the end has to be re-lined or sealed, and that is a manufacturing operation which is why lined capillaries are usually supplied with formed ends rather than cut ones.
- Every connection has the same problem. A compression fitting on a lined capillary compresses the tube and may crush the lining at the ferrule, and if the tube is then flanged the ferrule’s grip region is exposed. So the connection method is a design decision about the lining as much as about the pressure.
- Bending has the same problem. A bend tight enough to kink will crack the lining, and a bend merely tight enough to oval the tube will crack it too. So the minimum bend radius on a lined tube is set by the lining’s integrity rather than by the metal’s, and it is usually a larger number.
Surface finish, and it is a processing specification
Plating, coating or polishing per the print, with alternatives quoted alongside the quotation and samples approved in writing. On this part the finish is not the last operation – it is the functional one.
- External finish: conventional corrosion protection and handling. It does not affect the analysis, though a coating that flakes at a connection will put flakes into the flow path, so the external finish has a cleanliness requirement even where it has no analytical one.
- Internal finish: the functional specification, and it should be stated as a requirement rather than as a roughness. “Inert to trace analysis of the specified analytes”, or “deactivated”, is the kind of note that belongs on the drawing, and it is a note that requires an agreed test method – a blank run – rather than a measurement.
- End treatment: the ends are where the lining is either finished properly or destroyed, and the drawing should state the required end condition rather than leaving it to the fitting.
Dimensional accuracy, and where it does and does not matter
+/-0.02 mm on machined seats and sealing faces flat to drawing, with critical dimensions carrying CMM data. On this part the tolerance scheme’s priority is different from most of the tubes on this site, and the reason is worth stating.
- The bore matters, and it matters for a reason that is analytical as well as dimensional. A narrow bore increases the surface-to-volume ratio, and on an adsorption-limited system a larger ratio means more loss. So the bore’s size affects both the flow and the recovery, and the bore’s tolerance affects both.
- The wall matters because the lining has to fit on it, and a wall that varies along the length will carry a lining of varying thickness – and on a fused-silica coating that is a variation in the surface the analyte sees.
- And the flatness of any end that seals is as usual, because a connection that leaks is a connection that introduces air and contaminates the stream.
- What does not matter on this part: the outside diameter’s precision, except where it is a fitting interface. It is a handle and a support, not a functional dimension.
Inspection, and what verifies an analytical requirement
Drawn shell with machined seats and threads, batch records filed so a repeat order starts from approved data, and inspection on the CMM. Two kinds of check, and the second is the one that verifies the part’s purpose.
- Dimensional: the bore, the wall, the ends, and the fitting interfaces.
- A blank run or an analytical verification, on a sample, against the analyte of interest. This is the only test that verifies the lining, and it is a test with an agreed method rather than a measurement with a tolerance. On a lined capillary this is the acceptance criterion that matters, and if a customer is not going to do it then the lining’s specification is effectively unverified.
- Surface and interior inspection for scratches, chips and exposed metal, particularly at the formed ends – because an exposed edge is the failure mode that degrades performance slowly.
- And a pressure or leak test where the tube is a pressure line, which is a different requirement from the analytical one and does not substitute for it.
What analytes go through the tube, and at what temperature?
What analytes go through this tube, and at what temperature? Those two answers decide whether a lining is needed at all, which lining, and whether the tube can be plastic or has to be metal with a lining at all. They also decide the diagnostic requirement: a blank run with a specific analyte is a different and more demanding verification than a generic cleanliness check, and on a low-level application the customer’s expectation will be the blank run. And there is a second question that is nearly always missed on a lined capillary and that turns out to matter more than the lining: how is the tube handled between delivery and installation? Because the lining is a thin surface layer and a lined capillary that is scratched in transit, or bent below its radius, or gripped with a tool, will adsorb at those points for the rest of its life – and the degradation is not visible and not reversible. So the answer may be that the tube must be supplied with formed ends and a stated minimum bend radius and a handling note, and that note is a functional requirement rather than a courtesy. On a high-sensitivity application, the difference between a properly handled lined tube and a scratched one is often the difference between a result and a repeat.
Sensor Housings is the range this part sits under; the overview page pulls together the tooling logic, finishing options and tolerance notes that apply across the family.
Specifications
| Item | Stainless Steel Tall Thin-Wall Cylinder Tube |
|---|---|
| Brand | AUNOV |
| Designing | Made to your 2D/3D drawings (PDF, DWG, STEP, IGS) – DFM notes are returned before any tooling is cut; changes are priced before they are made. |
| Tooling | Our toolroom covers die design, wire-cut EDM and maintenance, so the die charge appears as its own quotation line, and the charge is refundable against agreed volumes. |
| Samples | Prototype and pre-production samples are provided against the drawing, so the approved first article becomes the gauge reference, and production starts only after your written sign-off. |
| Materials | Materials held include carbon steel, 304 / 316 stainless steel, aluminium and brass; grade and temper are confirmed in writing before tooling. |
| Surface finish | Zinc, nickel or chrome plating, anodising, passivation or e-coat; finish thickness and adhesion checked on the first article. |
| Processing | Where the print calls for them, seats and threads are machined into the drawn shell; batch records on file mean repeat orders start from approved data. |
| Equipment | Hydraulic presses for drawing, with CNC turning for finishing, backed by CNC turning centres and a climate-controlled inspection room. |
| Tolerance | +/-0.02 mm on machined seats, sealing faces flat to drawing; critical dimensions carry CMM data with the shipment. |
| Delivery terms | FOB as standard, with DDP offered for EU and US addresses; T/T or L/C, sea or air freight quoted to your door. |
Related Products
Frequently Asked Questions
Why is a chromatography support tube described as lined rather than stainless steel?
The requirement here is about adsorption, not pressure, so a bare steel surface would steal the analyte from the moving gas and the tube has to be lined. Everything follows from presenting a surface that will not adsorb or desorb the analyte.
What has the surface to do with a moving gas and its analyte?
It has to present a surface to a moving gas that will not steal the analyte, which is why a stainless steel tube is unusable for that purpose unless it has been lined, and why the lining is the actual specification. Plating, coating or polishing is per the print, with alternatives quoted and samples approved in writing.
Why is the tolerance scheme’s priority different on this tube?
Because the analytical requirement, not a pressure or fit dimension, is what inspection has to verify. Drawn shell with machined seats and threads, batch records filed so a repeat order starts from approved data, and inspection on the CMM, at +/-0.02 mm on machined seats and sealing faces flat to the drawing.
What analytes go through the tube, and at what temperature?
Those two decide what the lining has to be and how it is applied. What analytes go through the tube, and at what temperature, is the question that fixes the surface specification.
Request a Quote for This Part
Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).




