
A surface-mounting controller probe is a temperature sensor built for a control cabinet or a machine panel, and its whole reason for existing is that it has to be both a sensor and an electrical connection in one part. That is what makes it different from every other housing on this site, and it is why the mounting surface – rather than the process – is its critical feature.
Drawn shell with machined seats and threads where the print calls for them, at +/-0.02 mm on machined seats and sealing faces flat to drawing. So the tight band is on the machined features, and on this part the machined features are about mounting and about the electrical connection rather than about sealing.
A controller probe is three things, and each has its own requirements
- A temperature sensor. It measures, and the measurement’s accuracy depends on its thermal path to the process. On a surface-mounting probe the process is reached through the mounting surface, which is usually a thermal pad on a moulded plastic housing or a heatsink – and that path is not controlled by this part.
- An electrical housing. It carries a PCB or a terminal block, it has creepage and clearance requirements if it is mains-powered, and it may have an insulation or grounding requirement. This is a requirements set that has nothing to do with temperature.
- And a mounting interface. It bolts or clips to something, and the mounting surface has to be flat and, if the probe is also a heatsink, thermally conductive. So the mounting surface is a mechanical requirement and a thermal requirement at once.
And these three conflict, which is the design content on this page.
The mounting surface, which is the accuracy
On a surface-mounting probe the temperature reading is dominated by the path from the process through whatever the probe is mounted to and through the probe’s mounting face. That means the mounting face is a measurement surface and it needs three things.
- Flatness, over the full mounting area. A mounting face that is dished will rock on the heatsink or the panel, and a probe that rocks does not have a defined thermal path – it has a varying one, and the reading varies with the mounting pressure.
- Continuity of the contact area. This is a specific and frequently-missed requirement: the mounting face has to have a defined contact area, and where there are bosses or a recess in the middle the contact happens on the periphery. That is fine as long as it is intended, and it is not fine if the drawing specifies a flat face and the machining produces a pocket in the middle that the customer’s pad will not seat on.
- And a surface finish suitable for the thermal interface material. A ground or lapped face with a stated finish, so that a thermal pad or paste makes contact over its area rather than bridging the high points. This is the same thermal-interface requirement that appears on every heat-carrying part on this site, and it applies here with the difference that the interface material is usually somebody else’s.
So the practical question on this part’s mounting surface is: what is the probe being mounted to, and what interface material goes between them? Because a mounting face designed for a thermal pad and a mounting face designed for a metal-to-metal bolted joint are different geometries – the second needs to be flat and stiff, and the first needs to be flat and slightly compliant.
The electrical side, and why it changes the material question
Mill certificates and heat numbers on the first article, and a machined housing with seats and threads. If the probe is mains-powered or carries a switching signal, the electrical requirements arrive and they are not compatible with everything else.
- Creepage and clearance between the terminals and the housing. On a small housing the terminal spacing is fixed by the terminal block, and the housing’s walls have to stay a defined distance from it. This is a plastic-and-metal geometry question and on a drawn shell the wall’s thickness is set by the process, so the creepage requirement can conflict directly with the shell’s strength.
- Grounding and shielding. A controller probe often has a shield or an earth connection, and if the housing is conductive and part of that path then its surface finish and its connection to the terminal are functional. A passivated stainless steel housing conducts; an anodised one does not, which is a real and specific difference between two finishes that look similar.
- And the material choice shifts from thermal to electrical. An anodised aluminium housing is a good thermal part and a poor electrical one; a stainless steel housing is a good electrical part and a poor thermal one. So a probe that is both needs either a deliberate compromise or two parts – a metal shell for the earth and a thermally conductive mount for the temperature – and that decision belongs at the enquiry.
The drawn shell, and the machining that has to happen
Drawn shell with machined seats and threads where the print calls for them. On a controller probe the drawn features are the enclosure and the machined ones are the mounting pads, the terminal seats, the seal faces and any thread. Three design points on the boundary between them.
- The mounting pad has to be machined flat, and it has to be machined on a face the part can be held against. On a drawn shell the natural choice is the open end, but that means the pad is machined while the part is held on its outside – so the clamping has to be on something that is not a sealing surface and is not the mounting surface. That is a design decision: a part needs a clamping land, and where it is has to be planned.
- The terminal seat’s position and the mounting pad’s position have to be related to a single datum. A terminal block that is a tenth of a millimetre off the mounting pad’s centreline is a minor mechanical error and a major assembly problem, and it is free to avoid by naming one datum for both.
- And the enclosure’s sealing, if it has one. A controller probe in a cabinet is often not sealed – it is inside an enclosure – and if it is not sealed then the drawn shell does not need a sealing face and the tight band on the sealing faces is not applicable. If it is sealed, then the seal face is a real flatness requirement and it needs a datum.
Material, and the specific case of an anodised aluminium probe
Stock runs to carbon steel, 304 and 316 stainless steel, aluminium and brass. On a controller probe the usual answer is anodised aluminium, and it is worth being clear about what that gives and what it costs.
- It gives: good thermal conductivity – by far the best of the four for a surface-mounting probe – a corrosion-resistant surface, an insulating layer that prevents galvanic coupling to the mounting surface, and an appearance that suits a control panel.
- It costs: the anodised layer is a thermal insulator on the mounting face, so the mounting face has to be masked or the interface has to be designed around it. And an anodised layer is electrically insulating, so if the housing is part of an earth path it will not conduct through the anodic layer.
- Where the mounting face is masked and left bare, the probe is a good thermal part with a good-looking insulated body, and that is normally the right answer.
- Stainless Steel where the probe is in a conductive or a shielding requirement, or where corrosion is severe, with the thermal penalty accepted and the interface material specified to bridge it.
Three of the four requirements here are about the mounting face
Surface treatment matched to the duty, with masking and laser marking available. Four items, and on this part three of them are about the mounting face.
- The mounting face, masked if the design relies on bare metal for the thermal interface, or deliberately anodised if the design accepts the insulation and has specified the interface accordingly. What cannot be done is leaving it undecided.
- The terminal seat, masked where a screw terminal or a soldered connection is involved, because a plated seat changes the fit and a plated surface will not solder reliably.
- Any earth or shield connection, unmasked and with a defined finish, because that connection’s conductivity is a requirement.
- And the exterior appearance, which on a control-panel product is a real requirement and should be settled against an approved sample rather than a finish name.
A controller probe is flagged on its mounting features, not its outline
+/-0.02 mm on machined seats and sealing faces flat to drawing, with dimensional reports accompanying the first article. On this part the flagged dimensions are the mounting features rather than the outline.
- Mounting pad flatness – the primary requirement, and it should be tight enough to define the thermal interface.
- The position of the terminal seats relative to the mounting pad, as a relationship to a named datum. This is the tolerance that makes the part assemblable.
- Any mounting hole or spigot’s position, held so the probe locates rather than floats.
- Sealing faces, if the enclosure is sealed, as flatness and perpendicularity.
- And the drawn profile at the general band, with the wall’s minimum stated where the design depends on it.
Terminal seat position only means something relative to the mounting pad
Dimensional reports accompanying the first article, with a climate-controlled inspection room. On a controller probe the inspection items follow the three functions.
- Mounting pad flatness, on every part.
- Terminal seat position relative to the mounting pad, on the CMM, reported as a relationship.
- A thermal interface check – a contact pattern or a thermal resistance measurement against the specified pad – on a sample. On a surface-mounting probe this is the only test that verifies the thing the probe is for.
- Creepage and clearance verification, where the probe is mains-powered, as a measured value.
- And the earth or shield connection’s continuity, where there is one.
What is this probe bolted to, and through what interface material?
What is this probe being mounted to, and with what interface material? One question, and it decides the mounting face’s geometry, its finish, the masking list, and whether the probe’s material is chosen for thermal or for electrical reasons. Mounted on an aluminium heatsink with a thermal pad – and the mounting face is bare or masked, the material is anodised aluminium, and the probe is a fast thermal sensor. Mounted on a moulded plastic enclosure with a pad – and the probe’s wall thickness is now fighting against the pad’s compression and the design has to accommodate that. Mounted on a steel bracket with an earth requirement – and the housing may need to be conductive, which means stainless steel or a masked anodising scheme. And there is a second question that is nearly always missed on a surface-mounting probe: is the probe’s temperature accuracy measured at the mounting surface or at the process? Because a surface-mounting probe usually has no direct process contact at all – it is measuring through whatever it is bolted to – and so its stated accuracy is an accuracy at a remote point that depends entirely on the mounting. Two probes on the same drawing can therefore both be correct and read differently by several degrees, and the only thing that settles it is stating what the accuracy is claimed at.
Parts like this one sit under the Sensor Housings range, whose overview page gathers the tooling logic, finishing options and tolerance notes shared across the family.
Specifications
| Item | NTC thermistor temperature sensor surface mounting controller probe |
|---|---|
| Brand | AUNOV |
| Designing | Made to your 2D/3D drawings (PDF, DWG, STEP, IGS) – unusual walls, threads or tolerances are feasibility-checked first; the approved drawing is kept as the controlled master. |
| Tooling | Die design and toolmaking stay in house, so no tooling step is outsourced, and the charge is refundable against agreed volumes. |
| Samples | Sample approval is documented: dimensions, finish and material recorded for later comparison. |
| Materials | Stock runs to carbon steel, 304 / 316 stainless steel, aluminium and brass; mill certificates and heat numbers accompany the first article. |
| Surface finish | Surface treatment matched to the duty: plating, coating or polishing; masking and laser marking available where needed. |
| Processing | Where the print calls for them, seats and threads are machined into the drawn shell; batch records on file mean repeat orders start from approved data. |
| Equipment | Hydraulic presses for drawing, with CNC turning for finishing, backed by CNC turning centres and a climate-controlled inspection room. |
| Tolerance | +/-0.02 mm on machined seats, sealing faces flat to drawing; dimensional reports accompany the first article. |
| Delivery terms | FOB, CIF or DDP per Incoterms 2020, T/T or L/C, with D/P accepted on repeat business; each volume tier carries its own quoted price. |
Related Products
Frequently Asked Questions
What makes a surface-mounting controller probe different from other housings?
It is a temperature sensor built for a control cabinet or a machine panel, and its whole reason for existing is being both a sensor and an electrical connection in one part. That combination is what separates it from every other housing on the site. Drawn shell with machined seats and threads where the print calls for them runs at +/-0.02 mm on machined seats and sealing faces flat to the drawing.
Why is the mounting surface the critical feature rather than the process?
Here the mounting pad outranks the process as the critical feature, because three of the four requirements here are about the mounting face. The drawn features form the enclosure; the machined ones are the mounting pads, the terminal seats, the seal faces and any thread. Terminal seat position only means something relative to the mounting pad.
What does anodised aluminium give a controller probe, and what does it cost?
Anodised aluminium is the usual answer, and it gives a light, easily machined enclosure with a durable surface. Where the probe is bolted to a steel bracket with an earth requirement, the housing may need to be conductive instead, which points to stainless steel or a masked anodising scheme. Mill certificates and heat numbers accompany the first article.
What is this probe bolted to, and through what interface material?
Mounted on an aluminium heatsink with a thermal pad, the mounting face stays bare or masked for a fast thermal response. Mounted on a moulded plastic enclosure, the wall thickness now fights the pad’s compression and the design has to accommodate it. Stock runs to carbon steel, 304 and 316 stainless steel, aluminium and brass.
Request a Quote for This Part
Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).




