NTC Thermistor Sensor Housings

Stainless Steel Bullet Probe Tips, Ten-Piece
Stainless Steel Bullet Probe Tips, Ten-Piece

An NTC thermistor’s housing has one job that no other sensor housing on this site has to do: it has to hold a glass-encapsulated bead without letting the glass and the metal touch in a way that matters. Glass beads are brittle, they are sensitive to thermal shock, and they have leads that have to be anchored. So this housing is a mechanical and thermal design that happens to protect a piece of glass.

Deep drawing followed by CNC finishing on critical faces, at +/-0.01 mm on sealing faces and +/-0.05 mm on drawn profiles. So the tight band is on the sealing faces, and the rest of the part is a drawn shell – which is right, because the accuracy of this product is not in the metal.

The glass bead, and the three things that can kill it

A glass-encapsulated NTC bead is a small piece of glass with two leads coming out of it. Three things threaten it, and each has a corresponding requirement on the housing.

  • Thermal shock. Glass is a poor conductor and it is brittle, so a rapid temperature change across it will crack it. The housing’s contribution to this is its thermal mass: a heavy housing that heats slowly will protect the bead from a step change. That is the one place on a sensor where a heavy wall is an advantage rather than a defect, and it directly conflicts with the response time requirement. So a glass-bead thermistor in a heavy housing is a slow sensor with a protected element, and in a light housing it is a fast sensor with a fragile one.
  • Mechanical shock. A glass bead inside a housing can be broken by a shock transmitted through the housing – a drop, a hammer blow, a careless installation. The housing’s contribution is whether the bead is located with clearance or is in contact with the housing at one point. A bead that sits in a pocket with room around it survives; a bead that is bonded or crimped at one end transmits shock straight into the glass.
  • Lead failure. The two leads are fine wires coming out of the glass, and they are the part that fails first – usually by fatigue at the anchor point, where the wire is stressed by the element’s expansion. So where the leads are anchored is a design point and it is usually the weak point of the whole sensor.

Anchoring the leads, which is the real design task

Three arrangements, and each one fails differently. This is worth stating because it is the part of an NTC housing that nobody specifies.

  1. Bonded leads. The leads are bonded to the inside of the housing’s end wall. Cheap and it works thermally, but the adhesive’s temperature limits the sensor, and the bond is what fails on a thermal cycle. It also means the housing has to be designed for a bond rather than for a pocket.
  2. Crimped or pressed leads. A mechanical anchor, usually at the housing’s end or on an internal tab. It survives temperature better than an adhesive, and it is a controlled interference, so it is repeatable. Where it fails is on a thermal cycle if the crimp loses force – and then the leads move, and the element’s position moves with them.
  3. A loose bead in a pocket. The bead sits in a shaped pocket and is retained by the housing’s closure. This is the most robust mechanically and it is also the least thermally accurate, because the bead is surrounded by air and the air is an insulator.

And the design question that ties them together: is the bead touching the housing’s thermal path or not? A bead that touches the process wall conducts well and the housing is a sensor. A bead that sits in air behind a wall is a sensor with a wall between it and the process, and the wall’s thickness and material are the accuracy. Those are two different products and the drawing should say which.

The pocket’s geometry, if there is a pocket

Three dimensions, and all three are functional rather than dimensional.

  • Diameter, with clearance. A pocket sized to the bead’s nominal diameter leaves no room for the bead’s tolerance, and a pocket sized loosely lets the bead rattle and it can crack. So the pocket is a fit with a stated clearance and the clearance is a durability specification.
  • Depth and the position of the leads’ exit. The leads have to come out of the pocket without being pinched, and the slot they exit through is a stress concentration on the bead’s anchor. On a small sensor this slot is a laser cut or a punched opening and its edges are sharp, and those edges are where the leads fatigue.
  • And the pocket’s bottom’s position relative to the process wall, which is the thermal decision from the previous section stated as a dimension.

Surface finish, and one specific trap

Plating, coating or polishing to suit the drawing, with the finish inspected with the dimensional report on the first article. On this part there is one requirement that is a genuine trap.

  • If the leads are bonded, the bonding surface must be bare. A plated or passivated surface will not bond reliably – the adhesive keys onto the oxide, and passivation is deliberately producing an oxide. So if the design uses adhesive, the pocket and the anchor surface have to be masked from the plating or specified pre-finish, and on a drawn pocket the masking is a process step. This is a contradiction that is only discovered at assembly.
  • The sealing face, unmasked.
  • The thread, masked or specified post-finish with an allowance.
  • And the interior generally, where an element will sit: it should be clean and free of any residue, because a plated interior in a sensor whose leads are bonded is a build that will fail its own functional test.

Material, and the temperature limit

Carbon steel, 304 and 316 stainless steel, aluminium and brass, with the final grade fixed at the drawing review. On this part the material is bounded from both sides and one of those bounds is unusual.

  • The process side sets the corrosion requirement. 316L for chloride-bearing and for cleaning regimes, and the L grade if the housing will be welded.
  • The temperature is bounded from above by the glass and the bonding, not just by the metal. A glass bead’s thermal shock limit and an adhesive’s softening temperature are both lower than the metal’s capability. So a stainless steel housing on a high-temperature service can be perfectly adequate metal that cannot be used – and that is a real and frequently-missed constraint.
  • Aluminium where the wall needs to be thin and light, and its consequence is that an aluminium housing conducts better and is also a harder surface on the bead – which helps the thermal shock case and makes any contact between the bead and the housing a wear point.
  • Brass where good machinability and moderate temperature are the requirements, and its limit on a hot or a damp service is dezincification, which on a small sensor body is a loss of section rather than a visible failure.

The bead pocket’s diameter belongs to the customer’s element, not your band

+/-0.01 mm on sealing faces and +/-0.05 mm on drawn profiles, with capability checked on the first article. On this part the flagged dimensions are three, and none of them is the bead pocket’s diameter – which is because the pocket’s diameter is a fit to the customer’s element and it belongs on the drawing as a fit rather than as a band.

  • Sealing face: flatness and perpendicularity, measured as two values.
  • The pocket’s depth, because it is the element’s position in the thermal path and therefore the accuracy.
  • The lead-exit slot’s position and its edge condition, because the leads fatigue there.
  • And the pocket’s diameter as a fit with a stated clearance, not as a band – a clearance fit to the bead with the bead’s tolerance named.

Inspection, and the test that matters

First articles verifying the whole flow before the run is released. On an NTC housing supplied empty the inspection is dimensional. On one supplied with an element it is functional, and that difference is the difference between a component and a sensor.

  • Sealing face flatness and perpendicularity, on every part.
  • Pocket depth and a gauge check against the specified bead where an element is involved.
  • A functional resistance check against the curve at a reference temperature, on a sampled basis, where the housing is supplied with the element. This is the only test that verifies the element’s position, the leads’ anchor and the housing’s thermal coupling together.
  • And a thermal cycling check if the housing is bonded – because an adhesive anchor is the part most likely to fail and it fails on cycling rather than on a bench test.

Does the bead touch the thermal path, or sit behind a wall of air?

Does the bead touch the housing’s thermal path, or does it sit behind a wall of air? That one question decides the housing’s wall thickness, its material, its pocket’s depth and the sensor’s response time – and it is the difference between a thermistor that follows the process and one that follows the process slowly. Everything else follows from it. There is a second question worth asking because it is the one that actually breaks these products: how is the element’s lead anchored, and what happens to the anchor on a thermal cycle? Because a bonded anchor softens and creeps, a crimped anchor relaxes, and a loose bead is protected but thermally insulated – and on a product that will be cycled between a cold start and a hot process, hundreds of times over its life, the anchor is the failure mode. And there is a third, which is a commercial rather than a technical question but has a technical consequence: is this housing supplied empty or with the element fitted? Because an empty housing is a component with a price and a lead time. A housing with the element fitted is a sensor with a calibration, a functional test, and an accuracy claim – and the tolerance on the pocket, the material of the anchor, and the surface finish of the bonding surface all change depending on which of the two you are making.

You will find this part in our Sensor Housings range. Process notes, common materials and inspection points for every product in the family are collected across the sensor housings pages.

Specifications

ItemNTC thermistor temperature sensor housing
BrandAUNOV
DesigningQuotation follows the print, not a catalogue – unusual walls, threads or tolerances are feasibility-checked first; the approved drawing is kept as the controlled master.
ToolingProgressive and drawing dies are designed and built in house, so die cost stays transparent, and maintenance is tracked against the part number.
SamplesSample parts are measured and reported before submission, so the part is proven before it is made in volume, and the signed sample is kept for future reorders.
MaterialsCarbon steel (SPCC / DC01), 304 / 316 stainless steel, aluminium and brass are held on site; the final grade is fixed with the drawing review.
Surface finishPlating, coating or polishing to suit the drawing; the finish is inspected with the dimensional report on the first article.
ProcessingDeep drawing comes first, then CNC finishing on the critical faces; first articles verify the whole flow before the run is released.
EquipmentHydraulic drawing presses and CNC lathes for sealing faces, with CNC turning centres for secondary operations and CMM inspection.
Tolerance+/-0.01 mm on sealing faces, +/-0.05 mm on drawn profiles; capability is checked on the first article before the run continues.
Delivery termsCIF or DDP, with FOB available, T/T or L/C, with D/P accepted on repeat business; call-off schedules are supported.

Frequently Asked Questions

Why is an NTC thermistor housing a glass-handling problem?

The bead is glass-encapsulated, brittle, sensitive to thermal shock and has leads that must be anchored, so the housing protects glass rather than only enclosing a sensor.

How is the bead kept from touching metal where it matters?

The bore and lead path are drawn and finished so the glass sits in a recessed seat with clearance at the points that see shock, and the leads are anchored without stressing the bead.

What tolerances apply to the sealing faces?

Sealing faces are held to +/-0.01 mm and drawn profiles to +/-0.05 mm, because the accuracy of this product is in the seat, not the shell.

Can the housing be made from stainless steel and aluminium?

Both are offered – stainless steel for corrosion resistance and aluminium where weight or thermal mass matters, each drawn then finished on the critical faces.

Request a Quote for This Part

Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).