
A closed-end drawn tube for a sensor probe is a very small, very simple part, and it has one property that is easy to overlook: the inside is a cavity that the sensor’s accuracy depends on, and the cavity’s geometry is set by the drawing operation rather than by a machined feature.
That is the whole argument on this page. On a drawn probe the internal dimensions are consequences of the blank’s thickness and the punch’s penetration, not something that was machined to a specification – and the difference matters more on a probe than on any other drawn part.
How a drawn closed end is actually made
Carbon steel, 304 and 316 stainless steel, aluminium and brass, with mill certificates and heat numbers on the first article. The probe’s blank is a circular piece and it is drawn into a cup in one or more stages, and the geometry follows from that.
- The wall thickness is the blank’s thickness, minus what the drawing stretches and plus what the corner compresses. So the wall along the side is close to the blank, the wall at the closed end is less than the blank, and the wall at the corner’s inside is the thinnest point on the part.
- The internal depth is the punch’s penetration, and it is set by the tool – not by the drawing. So the cavity’s volume, which sets the probe’s response, is a tooling output that has to be specified and controlled like any other dimension.
- And the closed end’s thickness – the part that touches the process – is the thinnest section and it is the one the drawing stretched. On a probe that is both the thermally sensitive surface and often the pressure boundary’s most stressed section.
Why the cavity’s geometry is the accuracy
A sensor probe’s response is set by the mass that has to heat up. Three terms, and the cavity is the one that is hardest to change after the tooling exists.
- The element’s own mass. Not the housing’s responsibility, but it sets a floor on the response time.
- The cavity’s volume, because the fluid or gas in the cavity has to reach the process temperature before the reading is stable. On a small probe this is small and not a problem. On a longer probe – a thermowell-style immersion probe – it is the dominant term.
- The air gap between the element and the wall, if the cavity is unfilled. Air is a very poor thermal conductor and a small gap adds a lot of lag. This is the reason many probes are filled – with oil or with a thermally conductive potting compound – and it is a manufacturing decision with an accuracy consequence.
So on this part the useful specification is not the outside diameter and the length. It is: the cavity’s diameter, the cavity’s depth, and what is in it. Those three, with the element, set the response – and they are the numbers that a drawing organized around the part’s silhouette will omit.
The blind cavity, and why it is a dead zone
A drawn closed end is a blind cavity – it is closed at one end and it is not through. That has three consequences that apply to any drawn probe and that are worth naming because “blind” sounds like a limitation and is actually the reason the part exists.
- The trapped volume cannot be serviced or replaced. A drawn closed end cannot be opened without cutting the part, so whatever is inside – element, fill, air – is inside permanently. That makes the probe a consumable and it makes the cavity’s specification a one-time decision.
- The trapped air or fill has to be accounted for thermally. A cavity that is sealed at the factory with air in it is an insulator; a cavity filled with a good conductor is a conductor. Same metal, same geometry, different sensor.
- And the temperature at which the cavity was sealed matters. A cavity sealed at room temperature and then used at 200 degrees has air that has expanded, and either the cavity must be vented or it must be sealed with something that can accommodate it. This is the same vent question that comes up on every sealed sensor housing, and on a drawn closed end it is a specific and sometimes overlooked decision.
The mounting end, which is where the machining goes
Drawn shell with machined seats and threads where the print calls for them, at +/-0.02 mm on machined seats and sealing faces flat to the drawing. So the drawn part is the probe’s body and the machined features are its mount, and there are three of them that matter.
- The sealing face, flat and square to the axis, measured as two values. It is a seal and it is often the mount’s thermal couple.
- The thread, where the probe screws into a port, a fitting or a thermowell well. It has to be sealed or the well does not hold pressure, and a thread-sealing probe needs a taper or a bonded seal rather than a plain parallel thread.
- A gland or a spigot, for the lead or the connector, or for locating the probe in a well. Its depth and diameter set the seal’s compression and the probe’s position.
Material, and the specific consequence of the drawing process
Mill certificates and heat numbers on the first article, and four alloys available. On a drawn probe the material is chosen by the process, by the temperature, and by whether the probe is drawn or machined – and on a drawn probe the forming behaviour is part of the material choice.
- 304 and 316L for corrosion resistance, and the L grade where there is any welding in the assembly. On a drawn stainless steel probe the forming is harder – it work-hardens, needs more blankholder force and wears the tooling faster – and that is a cost consideration rather than a design one.
- Carbon steel where the process is benign and the temperature is moderate, with the corrosion protection coming from a coating. On a probe the coating has a thermal consequence – a coating on the process-facing surface adds a thermal resistance – and on a fast-response probe that matters.
- Aluminium where fast response is the requirement, and its forming is easy and its springback is the highest of the four, so its drawn dimensions will shift more than a steel’s.
- Brass where a plated exterior and good machinability matter and the temperature is moderate, and its limitation on a hot or a chemically aggressive service is dezincification.
A drawn probe’s finish is decided almost entirely by what is inside it
Plating, coating or polishing to suit the drawing, with masking and laser marking available. On a drawn probe the finish has three requirements and one of them is specific to this part.
- The sealing face, unmasked. A plated seal face does not seal.
- The thread, masked or specified post-finish with an allowance. A plated thread on a probe that screws into a pressure port is a leak path and it will flake into the process.
- And the process-facing interior or exterior, which is a product surface if the process is a product. In a food, pharmaceutical or medical application the drawn cavity’s inner surface is a documented, inspected surface and it needs its own finish specification and its own passivation record – and it is not covered by a general finish callout.
- Where the finish is thermal rather than cosmetic – a coating on the process side – the thickness is a thermal specification, because it sits in the thermal path. This is worth stating because a coating applied for appearance on a process-facing surface will be interpreted as part of the thermal design.
Tolerance, and why the cavity is not on it
+/-0.02 mm on machined seats, sealing faces flat to drawing, critical dimensions with CMM data. The tight band correctly goes to the machined features, and the drawn features carry the loose band. But the cavity – which is the part that sets the accuracy – falls in the drawn category, and that is a real gap.
- Sealing face: flatness and perpendicularity, measured as two values.
- Thread: class and pitch diameter, gauged.
- Gland or spigot: diameter, depth and concentricity.
- And the cavity: depth and diameter, specified as a requirement even though it is a drawing output. It will vary with the material and the tooling, and stating it as a band – a minimum depth, a maximum volume – is what turns a tooling consequence into a specification. On a probe where the response is a requirement, the cavity’s maximum volume is the number that matters, because it sets the worst-case response.
How fast must this probe answer, and what is going in the cavity?
How fast does this probe have to respond, and what is inside the cavity? Two questions, and they decide whether this part can be drawn at all. If the response requirement is loose and the cavity is going to be filled with a good thermal conductor, then a drawn closed end is entirely adequate – it is the economical answer, it is consistent, and the cavity’s geometry can be controlled by the tooling and specified as a band. If the response requirement is tight, then the cavity’s volume has to be small, the fill has to be a good conductor, and the wall has to be thin – and a drawn closed end starts to be constrained by the blank’s achievable thickness, at which point a machined solid or a welded closure starts to compete. There is also a question that is worth asking on a drawn probe because it is nearly always unanswered: is the cavity vented, and at what temperature was it sealed? A blind cavity sealed at room temperature and used hot has an internal pressure problem, and whether that is solved by a vent, a flexible element, or a fill that can accommodate it is a decision that has to be made before the part is made – and it is much harder to change after the tooling exists.
This part belongs to our Sensor Housings range. The sensor housings pages collect the process notes, common materials and inspection points behind every product in the family.
Specifications
| Item | Stainless Steel Sensor Tube with Center Bore and Base Flange |
|---|---|
| Brand | AUNOV |
| Designing | Driven by your drawing or a physical sample – samples are reverse-measured into a controlled drawing; the approved drawing is kept as the controlled master. |
| Tooling | Tooling is built and held under your part number, so tooling lead time stays under our control, and first-article timing is measured from the tooling start date. |
| Samples | Sample parts are measured and reported before submission, so any deviation is corrected at sample stage, and later batches are gauged back to the signed sample. |
| Materials | Carbon steel (SPCC / DC01), 304 / 316 stainless steel, aluminium and brass are held on site; mill certificates and heat numbers accompany the first article. |
| Surface finish | Plating, coating or polishing to suit the drawing; masking and laser marking available where needed. |
| Processing | Drawn shells receive machined seats and threads where the print asks; filed batch records let a repeat order start from approved data. |
| Equipment | Hydraulic drawing presses and CNC lathes for sealing faces; secondary ops run on CNC turning centres, inspection on the CMM. |
| Tolerance | +/-0.02 mm on machined seats, sealing faces flat to drawing; critical dimensions carry CMM data with the shipment. |
| Delivery terms | FOB, CIF or DDP per Incoterms 2020, T/T with deposit and L/C for larger runs; repeat orders reuse the approved first article. |
Related Products
Frequently Asked Questions
Why is a drawn closed end a blind cavity rather than a through hole?
A closed-end drawn tube is closed at one end and is not through, so its inside is a dead zone that the sensor’s accuracy depends on. The cavity’s geometry is set by the drawing operation rather than by any machined feature, which is easy to overlook on such a small, simple part. A blind cavity sealed at room temperature and then used hot develops an internal pressure problem.
What should the drawing specify instead of outside diameter and length?
On this part the useful specification is the cavity’s diameter, the cavity’s depth, and what is in it, not the outside dimensions. So specify the cavity and leave the outside diameter to follow, because the sensor responds to the cavity, not the silhouette. Drawn shell with machined seats and threads where the print calls for them, at +/-0.02 mm on machined seats and sealing faces flat to the drawing.
When is a drawn closed end adequate, and when is it constrained?
If the response requirement is loose and the cavity will be filled with a good thermal conductor, a drawn closed end is the economical, consistent answer. If the response is tight, the cavity’s volume must be small, the fill a good conductor and the wall thin, and the drawn end starts to be limited by the blank’s achievable thickness. At that point a machined solid or a welded closure starts to compete.
Is the cavity vented, and at what temperature was it sealed?
This question is nearly always unanswered, yet it decides whether the internal pressure problem is solved by a vent, a flexible element or an accommodating fill. That decision has to be made before the part is made, and it is much harder to change after the tooling exists. Mill certificates and heat numbers accompany the first article.
Request a Quote for This Part
Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).




