Aluminum CNC Machined Mounting Brackets

Black Powder-Coated L Bracket with Round Bore
Black Powder-Coated L Bracket with Round Bore

A small aluminium mounting bracket is one of the most frequently specified and most frequently mis-specified parts on this site, and the reason is that it looks like a plate with two holes and it is actually a structural part whose whole job is to resist a moment. The two holes are the interface. Everything else about the bracket exists so that the two holes stay in the right places under load.

This part is stamped rather than machined, which changes its tolerance philosophy completely and is covered in detail on the stamping page. What is worth saying here is specific to aluminium brackets and to the way they are designed.

The load, and what it does to a thin plate

A bracket that mounts something to something is usually asked to resist three loads, and they produce different failure modes.

  • Shear, where the load is parallel to the mounting face. This is the easiest case and it is the one most brackets are sized for. The bolt holes’ bearing strength is the limit and it is a straightforward calculation.
  • Tension or compression, where the load is perpendicular to the face and pulls the bracket off or pushes it onto its mounting surface. This is where a thin sheet bracket fails at the bolt hole – the bearing stress plus the tearing of the material between the hole and the edge.
  • Moment, where the load is offset from the mounting face. This is the case that decides most brackets, and it is the one that is usually under-designed because it is the one that is not obviously a load.

And the moment case produces a specific structural conclusion: the bracket will fail at the mounting face, not at the load’s application point. A cantilever bracket loaded at its end will typically tear at the bolt hole or at the section where it meets the mounting face, because that is where the moment produces the highest bending stress in the bracket’s own material. This is worth stating because it means the whole design effort goes into the root of the bracket rather than into the far end, and it is where additional material pays off.

Where to put the material

On a thin aluminium bracket this is the central design question, and the answer is a property of bending that is worth understanding.

  • Depth in the direction of the load beats width. A section’s stiffness depends on the square of its depth and only linearly on its width. Doubling a bracket’s width roughly doubles its stiffness; doubling its depth roughly quadruples it. On a bracket that is too weak, deepening the flange at the root is the single most effective change, and it costs nothing if the space is there.
  • A flange at the root is worth more than a thicker web. A bracket with a small flange at the mounting face will carry considerably more than a bracket that is simply uniformly thicker, and it uses less material.
  • A gusset or a web between the root and the load. On a bracket carrying a real moment this is the standard answer and it is frequently absent from an initial drawing.
  • The bend is the weak section, and this is specific to a stamped bracket. The bend’s outside fibre is at its strain limit from the forming, so it has no margin left. A cyclically loaded aluminium bracket will fatigue at the bend, and the response is a bend relief, not a thicker material.

Aluminium, and the specific reason a bracket might not be aluminium

1050, 3003, 5052 and 6061 at 0.5 to 3.0 mm stock, with the temper matched to the route. Three points that are specific to a stamped aluminium bracket.

  • Temper is a forming requirement and a service requirement. A bracket with two or more tight bends needs a temper that will form without cracking – a quarter-hard or dead-metal temper for 5052 and 6061. But a dead-metal temper has low yield, so the formed bracket will be weaker than the same bracket in a half-hard temper. On a bracket whose strength matters, the temper and the number and tightness of the bends have to be considered together, and this is a genuine trade that is usually resolved by adding a bend relief rather than by changing the temper.
  • Aluminium’s fatigue strength is low. On a cyclically loaded bracket this is a design limit. A 5052 bracket will outlast a 6061 bracket in a fatigue application because 5052 has considerably better fatigue resistance even though 6061 is stronger. This is counterintuitive and it is a real result.
  • 5052 versus 6061 versus 1050: 5052 for general structural sheet with good formability and corrosion resistance; 6061 where higher strength is needed and the forming is gentle; 1050 and 3003 where the bracket is not structural and appearance and formability are all that matter.

Surface treatment, and the four things a bracket needs masked

Surface treatment matched to the duty, with the finish inspected with the dimensional report on the first article. On an aluminium mounting bracket the treatment is often a powder coat or an anodise for appearance, and there are four specific items that need masking or a stated allowance.

  • The bolt holes. A coating closes them, which is generally acceptable on a clearance hole and a problem on a locating hole. But a coated hole on an aluminium bracket also means the fastener’s bearing is on a coating, and a powder coat’s thickness under a washer head is a soft layer that will compress – which changes the clamp preload and which is a functional consideration.
  • Any hole that has to accept a dowel or a pin should be masked, because the coating changes the fit and a locating pin in a coated hole will not locate the same way.
  • Any face that seats against something to transmit a clamp load. This is a real one: on a powder-coated bracket, the clamping force has to crush the coating to reach the metal, and a powder coat’s yield strength is low enough that the joint can lose preload at temperature or over time as the coating creeps slightly.
  • Any thermal contact face, and this is the anodising case again. An anodised bracket that is supposed to conduct heat through its mounting face is an insulator at exactly the wrong place.

Where the bracket is powder coated, there is also a thickness specification that is not cosmetic: a typical powder coat is 60 to 120 microns, which is a meaningful fraction of a 1 mm sheet’s bend allowance and which changes the effective thickness at every bend. On a bracket where the bend’s angle is a fit – a hook, a lip, a slot – the coating’s thickness has to be in the geometry.

Flag the stamped features that springback does not touch

+/-0.05 mm to +/-0.1 mm across the part, GD&T per drawing, PPAP-style reports on request. On a stamped bracket the flagged dimensions should be chosen by asking which features are not affected by springback, because that is the discipline that makes a stamped part’s tolerance scheme sensible.

  • The mounting holes’ positions to each other and to the part’s outline, where the outline is pierced in the same operation. Pierced features in the same die station are positioned to the feed, and they are much more repeatable than features that come from bending.
  • The holes’ position to the part’s functional datum, and the datum named. On a bracket the datum is almost always the mounting face, because that is what registers against the thing it mounts to.
  • Flatness of the mounting face, because the bracket’s whole job is to bear on that face.
  • Any locating hole’s diameter and position, tightly, and masked from coating.
  • Bend angles and bend positions, held to a general band and accepted as varying with the material lot. Trying to hold a bend angle tightly on a stamped part is asking to spend money where the material’s own variation will not let you.
  • The overall outline at the general tolerance, unless it locates something or it is a mating edge.
  • Thickness as a minimum, on the structural sections, because the gauge is the bracket’s strength and stiffness.

Flatness means nothing unless the bracket is in its real support condition

  1. The mounting holes’ position, on the CMM, and the hole pattern’s relationship to the mounting face.
  2. Flatness of the mounting face, checked with the bracket in its actual support condition.
  3. Bend angles and the bend’s position, verified against a master, and – this is the specific point for a stamped part – verified across more than one material lot after the first production run, because a first article from one coil proves nothing about the next one.
  4. Burr and edge condition on the outline, the holes and every formed feature. On a stamped aluminium part this is a real inspection item and a common cause of handling complaints.
  5. A functional fit check against the mating part, on a sample. On a bracket this tests the hole pattern, the flatness and the mounting face together in seconds.
  6. Coating thickness and adhesion on the first article, with the masked holes and faces verified.

Steady load or cyclic, and a moment or a pull

Is this bracket loaded steadily, or does the load cycle – and is the load a moment, or is it a direct pull? Those two questions decide whether this is an ordinary stamped plate or a fatigue-critical structural part, and the difference is large enough to change the design. A steadily loaded bracket carrying a direct tension is the simple case: the hole bearing and the tear-out are the design, and a general tolerance bracket in a general alloy is entirely adequate. A bracket carrying a cyclic moment – a hinged arm, a door bracket, a bracket on a machine that vibrates – is a different part, and its whole design effort goes into the root section and the bend. The bend in particular: a cyclically loaded aluminium bracket will crack at the bend’s outer fibre, and the fix is a bend relief, which is a small change to the flat pattern and costs nothing. There is also the third question worth asking at the same time, which is whether the bracket could be an extrusion or a machined part instead – on a bracket with a constant cross-section, an extruded profile removes the bend entirely, which on a fatigue-critical bracket is the single best improvement available. Three questions, and on a bracket they can turn a stamped plate into an extruded structural section.

Custom Metal Stamping Parts is the range this part sits under; the overview page pulls together the tooling logic, finishing options and tolerance notes that apply across the family.

Where this part is used

A small aluminium mounting bracket is one of the most frequently specified and most frequently mis-specified parts in this range, because it looks like a plate with two holes and it is actually a structural part whose whole job is to resist a moment. The two holes are the interface; everything else on the bracket exists so that the two holes stay in the right places under load.

You will find them everywhere light structures are assembled – control and instrumentation panels, small motor and gearbox mounts, sensor and camera brackets, electronics enclosures, and the mounting plates inside machinery. They are almost always aluminium, because that is what the surrounding structure is, and the specific reason a bracket might not be aluminium is worth checking early: galvanic corrosion against a steel or zinc fastener is a real failure mode in exactly this kind of assembly.

What we need to quote it

Send the hole spacing, the material and temper, the stock thickness, and the load – a steady weight, a cyclic load, and whether it is a moment or a pull-off. Those three answers determine whether the bracket is a stamped pressing or a machined part, and whether the thickness has to go up rather than the geometry. Tell us what it bolts to and what it is bolted with, so we can check for galvanic pairing, and state which surfaces must be masked for anodising or coating.

Specifications

Frequently Asked Questions

What thickness and geometry does an aluminium bracket need for a given load?

Direct answer: It depends on which load case governs, and for a small stamped bracket it is usually the moment rather than the shear. Shear at the bolt hole is the easy case and is what most brackets are sized for, but a bracket loaded away from its mounting face fails at the root section rather than at the load point, because that is where the bending stress is highest. So the design effort goes into the root – a deeper web, a thicker section, a longer foot – rather than into the hole area, and we will say which case governs on your drawing.

Aluminium bracket – stamping or machining, and which suits which load?

Direct answer: When the load is high relative to the bracket’s size, when the hole positions have to hold to a tight band, or when the aluminium grade available will not form cleanly at the required depth. We hold 0.5 to 3.0 mm aluminium stock and can form 1050, 3003, 5052 and 6061, with temper matched to the forming depth. What disqualifies a stamped route is usually the tolerance on the hole pattern rather than the material – and if the holes have to be located precisely, a machined route can be the cheaper answer.

How do we stop an aluminium bracket corroding against steel fasteners?

Direct answer: By separating them deliberately rather than hoping the coating is enough. Aluminium and steel in direct contact with moisture present a real galvanic coupling, and the aluminium is the anode that corrodes. The options are a stainless steel or passivated fastener, a plating or coating system that isolates the surfaces, or an insulating washer or shim between them. We mask the contact faces during finishing so the coating actually reaches them, and we can specify the fastener material on the drawing if you tell us what is bolting it.

ItemAluminum CNC Machined Mounting Brackets
BrandAUNOV
DesigningSend drawings, or send a sample to be measured – a manufacturability review comes back with the quotation; the agreed version governs every later batch.
ToolingProgressive and drawing dies are designed and built in house, so the die charge appears as its own quotation line, and first-article timing is measured from the tooling start date.
SamplesThe sample you approve becomes the gauge reference for production.
Materials1050 / 3003 / 5052 / 6061 aluminium, 0.5-3.0 mm stock – temper matched to the forming depth or machining route of this bracket.
Surface finishSurface treatment matched to the duty: plating, coating or polishing; the finish is inspected with the dimensional report on the first article.
ProcessingCoil-fed stamping, deburred and finished to the print; in-process checks sit between stages, not only at the end.
EquipmentPress shop with 5-250 T mechanical presses and dedicated dies; secondary ops run on CNC turning centres, inspection on the CMM.
Tolerance+/-0.05 mm to +/-0.1 mm across the part; GD&T per drawing, PPAP-style reports on request.
Delivery termsFOB, CIF or DDP per Incoterms 2020, payment by T/T, L/C at sight or D/P; repeat orders reuse the approved first article.

Request a Quote for This Part

Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).