Hex Head Sensor Housing – Deep Drawn SS

Hex Head Sensor Housing - Deep Drawn SS | Aunov Tech
Hex Head Sensor Housing – Deep Drawn SS

A hex head is not a shape, it is an assembly contract

A hex head on a sensor housing looks decorative and is anything but. It exists so that the housing can be gripped by a wrench, dropped into a panel or a manifold with a hex drive, held by a nut rather than a thread, and located against a flat face without rotating. Every one of those functions places a requirement on the hex that is separate from the sensor’s requirements – and the two sets of requirements frequently conflict, because the hex wants flat faces and square corners while the housing wants a thin drawn wall.

We make these as a drawn shell with machined seats and threads where the print calls for them, on hydraulic drawing presses with CNC lathes for sealing faces, secondary operations on CNC turning centres, and CMM inspection. Stepped bores are held to +/-0.03 mm with concentricity per the print, and capability is checked on the first article before the run continues. Standard stock is carbon steel in SPCC and DC01 grades, 304 and 316 stainless steel, aluminium and brass, with grade and temper confirmed in writing before tooling. This page covers what a hex actually has to do, and why it is often the hardest feature on the part.

What a hex has to satisfy

A wrench does not grip a hexagon; it grips the corners. Across flats, the wrench applies force and the load is carried by the flat faces. That produces a short list of real requirements:

Across-flats dimensionThe size the wrench fits. This is the one dimension everybody specifies, and it is a wrench-fit dimension rather than a thread dimension – which is why it is often specified loosely and then causes a problem.
Corner radiusNot optional. A sharp corner in a hex is the first thing to deform, and a wrench on a sharp corner rounds it immediately. A specified corner radius is what makes the hex repeatable across a batch.
Height of the hexToo short and the wrench bottoms out on the housing wall and rounds it. Too long and it projects into the space the sensor needs.
Flatness of each faceThe wrench bears on the face across its width. A crowned or dished face concentrates load at the edges, which is both a marking problem and a durability problem.
Parallelism of opposite facesTwo faces that are not parallel make the part sit unevenly in a wrench and wear asymmetrically.
Concentricity to the boreWhere the housing has a bore, the hex has to be centred on it or the part will not sit square in whatever it is mounted into.

Now the conflict: a hex head wants substantial material for rigidity and to resist rounding, while a drawn sensor housing wants thin walls for a small package and for easy forming. The resolution is usually a machined or extruded hex boss – a raised feature with real section depth – rather than a hex formed in a thin drawn wall.

How a hex gets made, and what each method implies

  1. Formed in the draw. A hex formed during drawing flows material into the corners. It works for a relatively shallow hex in a reasonably thick wall, and it produces a hex whose corners are naturally radiused. It is the cheapest method and the one most likely to distort, because forming a polygonal feature creates material flow in two directions at once.
  2. Formed in a secondary operation. A hex drawn or machined after the shell is made, in a separate press stroke or on a lathe. Better control on the corner radius and the flatness, and it keeps the hex’s forming forces out of the sensor shell – which protects the shell’s dimensional accuracy.
  3. Machined from solid. Full control on every feature, and the only route to a tight tolerance on the bore with a hex around it. It is the most expensive and it is what tight parts need.
  4. A separate hex nut or insert. The housing has a thread or a bore and a separate hex-bodied component provides the wrench interface. This is the right answer when the hex needs to be in a different material, or when it needs to be replaceable, or when the housing’s own wall is too thin for any hex.

The choice worth discussing at review is usually between a formed hex and a machined one, and it turns on three questions: how tight is the bore, how much torque will the wrench apply, and how thin is the wall the hex has to be carried on.

Stepped bores at +/-0.03 mm, and why concentricity is separate

The stepped bore is where the sensor locates and where fluid is sealed, and the tolerance structure around it is worth reading carefully:

  • Size at +/-0.03 mm controls fit – whether the element enters, and whether an O-ring is correctly compressed.
  • Concentricity per print controls the relationship between the bore and something else, almost always the hex or the outer diameter. It is a separate call because a bore can be perfectly in size and perfectly round while sitting off the part’s axis.
  • Runout, if specified, controls the whole surface including taper. On a bore that has been machined, this is the more meaningful control.

The practical reason concentricity matters on a hex head specifically: if the bore is off-axis relative to the hex, then mounting the part in a wrench, a nut, or a hex-drive socket puts a side load on the bore, and side load on a sensor bore is what causes the element to bind and the seal to wear unevenly. It is a low-probability fault that produces an intermittent, hard-to-diagnose failure, which is exactly the kind of thing the concentricity callout exists to prevent.

Drawn shell + machined features: the interaction

The route on this part is a drawn shell with machined seats and threads. The interaction between those two stages produces a few requirements worth stating:

  • The machining allowance has to exist. A machined seat is cut from a drawn surface, so the drawing must show that the drawn feature is oversize. Without it, the machined seat ends up short and the part does not seal.
  • The drawn shell distorts under machining. Clamping a thin drawn shell to machine a face can deform it, and it springs back afterwards. Where the sealing face is being machined, the support has to follow the part’s shape and the allowance has to be enough to clean up the distortion rather than lock it in.
  • Sequencing matters for the hex. If the hex is machined, it should generally be machined after the shell is finished, or in a fixturing arrangement that locates from the shell’s own datum. Machining the hex first and drawing afterwards would put the drawing’s forming forces through a machined feature.
  • Batch records are filed so a repeat order starts from approved data – which on a hex part matters because hex across-flats drifts with tool wear on a forming punch in a way that a general tolerance will not catch.

Finishes on a hex part, and the one that gets missed

Zinc, nickel or chrome plating, anodising, passivation or e-coat are all available, with masking and laser marking where needed. For a hex head specifically, one requirement dominates: the flats must not be coated in a way that changes the wrench fit.

  • A plated hex grows. Plating adds thickness on every surface, so across flats increases and across corners increases more. Where a hex is driven by a fixed wrench, that growth is a fit problem. The drawing should say whether across flats is specified before or after plating – and on a driven hex, after plating is usually what matters.
  • The corners build up more. A corner has more surface than a flat per unit of projection, so plating thickness there is effectively greater, and the corner radius grows. This is normally beneficial – it softens a sharp corner – but it means the corner radius is not the bare-steel radius.
  • E-coat or powder coating on a wrench feature is a nuisance. A thick dielectric film on flats means the wrench marks the coating rather than the metal, and repeated tightening cuts through it. Where the hex is a working surface rather than a visual one, a thin metallic plating is usually the right choice.
  • Passivation on stainless steel is the default and needs no masking – unless the part is also plated, in which case the plating route is a separate decision.

Masking on a hex part is usually specified for the threaded portion and for the sensing or mounting face, and less often for the flats. Each of those is a separate decision, and the cheapest is to make them all on the drawing at once.

Materials, and a note specific to hex heads

Carbon steel, 304 and 316 stainless steel, aluminium and brass are all held, with grade and temper confirmed in writing before tooling. The hex-specific consideration is hardness: a hex that is too soft rounds; a hex that is too hard in a brittle material cracks at the corner. Steel in the harder tempers resists rounding and is fine in normal service. Aluminium hexes round quickly and are usually specified with a generous corner radius or with a separate steel insert. Stainless Steel hexes are the standard case for galling to be considered at the mating nut, which is an assembly decision and is worth raising at review rather than after the first service complaint.

What to review before tooling

Your drawing sets the part, DFM notes come back before any tooling is cut, and the same drawing is used for every repeat order. Dies, fixtures and gauges are made in our own toolroom so the die charge appears as its own quotation line and ownership is confirmed on the quotation. Samples are issued for approval before the run, the sample is retained as the master, and mass production is gated on that approval.

Six things that make a hex-headed sensor housing repeatable:

  1. Across flats stated before or after finishing. The single most consequential line on the drawing for this part type.
  2. Corner radius specified, rather than left to the tool.
  3. Flatness and parallelism of the hex faces, because the wrench bears on them.
  4. Concentricity of the bore to the hex or the outer diameter, as a separate call from bore size.
  5. Where the part is clamped for machining, or at least a surface designated as non-functional so it can be.
  6. Which tolerance on the drawing is functional – the seal, the sensor seat, or the wrench fit.

And the question worth asking: does the hex need to be part of this part at all. A separate insert, a nut, or a different mounting method can remove the hardest feature on the design, and on a part with a thin drawn wall that is often the right question to have asked at the start.

This part belongs to our Sensor Housings range. The sensor housings pages collect the process notes, common materials and inspection points behind every product in the family.

Specifications

ItemHex Head Sensor Housing – Deep Drawn SS
BrandAUNOV
DesigningYour drawing sets the part – DFM notes are returned before any tooling is cut; the same drawing is used for every repeat order.
ToolingDies, fixtures and gauges are made in our own toolroom, so the die charge appears as its own quotation line, and ownership is confirmed on the quotation.
SamplesSamples are issued for approval before the run, so the sample is retained as the master, and mass production is gated on that approval.
MaterialsStandard stock: carbon steel (SPCC / DC01), 304 / 316 stainless steel, aluminium, brass; grade and temper are confirmed in writing before tooling.
Surface finishZinc, nickel or chrome plating, anodising, passivation or e-coat; masking and laser marking available where needed.
ProcessingDrawn shell with machined seats and threads where the print calls for them; batch records are filed so a repeat order starts from approved data.
EquipmentHydraulic drawing presses and CNC lathes for sealing faces; secondary ops run on CNC turning centres, inspection on the CMM.
Tolerance+/-0.03 mm on stepped bores, concentricity per print; capability is checked on the first article before the run continues.
Delivery termsFOB, CIF or DDP per Incoterms – payment by T/T or L/C, with shipping quoted door-to-door.

Frequently Asked Questions

Why put a hex head on a sensor housing instead of a plain round body?

The hex lets the housing be gripped by a wrench, dropped into a panel or manifold with a hex drive, and held by a nut or a flat face rather than a thread, so it locates and stays put without rotating. That job is separate from the sensor’s own requirements, and the hex is the feature that takes the assembly load off the thin drawn wall.

How is the hex held square to the drawn sensor body?

The hex is a machined or extruded boss located off the same drawn datum as the rest of the shell, so its faces relate back to the body in one setup rather than being measured in afterwards. Concentricity and the across-flats band are verified on the CMM because a hex that runs out will not seat the wrench or the panel square.

Which stainless steel is used for a hex-head sensor housing?

304 is the default for general duty, with 316 for chloride or marine exposure, and the grade is matched to the environment the housing sees. Mill certificates with heat numbers accompany the first article so the shipped parts trace to the coil and the approval.

What tolerance holds the stepped bore on a hex-head sensor housing?

Stepped bores are turned on the CNC lathe and held to a few hundredths of a millimetre, with concentricity to the print, because a sensor seats on those bores and they must repeat across the run. Capability is checked on the first article before the full run begins, and the band is confirmed against the drawing rather than assumed.

Request a Quote for This Part

Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).