
A stainless steel probe shell with domed top boss is a drawn shell closed at the top by a rounded dome carrying a formed boss that sets the mounting and the cable exit. The dome protects the element and presents it to the process, while the boss is what the shell seats or threads against. The shell’s job is to keep the element thermally and mechanically isolated while staying small enough to fit where the probe has to go.
Deep drawing followed by CNC finishing on critical faces, at +/-0.02 mm on machined seats and sealing faces flat to drawing, with critical dimensions carrying CMM data. So the tight band is on the machined seats – and on this part the seats are where the cleaning happens.
What a food probe has to survive that an instrument probe does not
- A cleaning cycle that is harsher than the process. Dishwasher cycles involve hot detergent, and a probe used in a smoker or a freezer may see thermal cycling between minus forty and two hundred degrees. So the material, the adhesive at the handle, and the seal all have to survive a regime that has nothing to do with what is being measured.
- Being dropped. A food probe is dropped onto a hard floor – out of a sink, out of a rack. That is a shock load on a thin probe with a fragile element inside, and it is the most common way these parts break.
- Being gripped wet and hot. The handle is held with a wet hand and often with tongs, so the handle’s grip and its thermal isolation are functional. A handle that conducts heat from the pan into the hand makes the probe unusable, and a handle that is too smooth is unusable in a wet hand.
- And being scrubbed. Contact with a scourer, a sponge, and detergent means the surface has to tolerate abrasion. On a polished stainless steel probe, abrasion happens and a scratch is a corrosion site.
The cleanability requirement, which is not a surface finish
This is the part that gets handled as a cosmetic note and is not one. A product-contact surface has requirements that a general plating or coating callout does not address.
- Surface roughness with a convention, because the cleaning depends on it. A rough surface retains soil in its valleys; a smooth one drains. On a probe that goes into a crevice and is washed, the finish is what determines whether it cleans.
- Drainability, which is geometry. A probe with a closed cavity between the handle and the shaft will hold water, and the water will be inside it forever. Where a seal separates two sections, the seal has to be drainable at the bottom, and on a probe that is usually a small hole in the handle or a deliberate relief at the joint – which is a design feature and it has to be specified.
- No crevices and no blind pockets on the product-contact side. The same cleanability principle that appears on the hygienic fitting pages applies here: a food probe is a hygienic fitting with a temperature sensor in it.
- And the material’s own requirement. Where the probe is in contact with acidic food, or is cleaned with acidic agents, 316L rather than 304 – because a food product is frequently the most aggressive thing a probe ever sees. Tomato, citrus, vinegar and salt are all more aggressive than the water supply.
The handle, which is where a food probe differs most
A food probe has a handle, and on an instrument probe there is nothing equivalent. The handle does four things and they conflict.
- Thermal isolation. The hand must not feel the pan’s heat, so the handle has to break the thermal path from the probe’s tip to the hand. That means a long enough stem or an air gap or both, and it is a design dimension rather than a comfort item.
- Grip. Wet, greasy hands need a handle with texture or a shape, and a smooth stainless steel handle in a wet hand is a dropped probe. So the handle’s surface or its form is functional.
- Sealing. Where the handle meets the probe’s shaft there is a joint, and if the handle is a different material there is a seal at that joint. That seal is a product-contact-adjacent feature and it is a wear item.
- And the cable’s exit, which on a food probe is the weakest point in the assembly. The cable enters the handle, the cable’s jacket is sealed where it enters, and that seal has to survive the dishwashers and the tugging that comes with using a probe.
So on a food probe the handle carries four requirements and none of them is dimensional, which is why the handle’s specification tends to be the thinnest part of the drawing.
The element and the seal, which is where the food requirement bites
- The element is inside the probe, so the food requirement is on the interior. The interior has to be a cleanable, non-shedding surface, and on a probe with a bonded element that means the bond’s integrity and the interior’s finish.
- The seal between the element’s section and the handle’s section is the boundary between the wetted part and the dry part, and it has to be a food-grade sealable joint – which is a materials specification, not a dimension.
- And on a probe that measures directly in a liquid, the wetted length is specified separately from the probe’s length, because a customer will immerse a defined depth and that depth is part of the measurement.
Accuracy on a food probe, which is different again
A food probe’s accuracy has three contributions and only one of them is the sensor.
- The sensor’s own accuracy – which on an NTC or a thermocouple is a percentage of reading or an offset plus a span.
- The immersion depth error, which is the conduction error from the unimmersed length and which is significant on a handheld probe because the operator’s immersion depth varies.
- And the thermal mass of the probe itself. A probe with a large tip mass reads correctly in equilibrium and lags badly during a transient – and cooking is a transient. So a food probe in a roast that comes out of the oven has a reading that depends on how long it was in there and how thick the food is.
Which produces the practical conclusion that a food probe’s accuracy figure is meaningless without a condition attached: at what immersion depth, and at what response time. Two numbers that turn a generic accuracy claim into a verifiable one.
Food compatibility comes before corrosion on a food probe
Deep drawing presses and CNC lathes for the sealing faces, secondary operations on CNC turning centres, inspection on the CMM. On a food probe the material has three jobs and the first is not the one people think.
- Food compatibility. 316L where the food is acidic, salty or both – which is most food. And on a food-contact application the specific grade and its certification are a documented requirement, not a general “stainless steel” note.
- Dishwasher and thermal cycling survival. Where the probe’s process is a moulded or bonded plastic, the plastic’s ability to survive repeated hot detergent cycles is a design constraint on the housing, not on the sensor.
- And the handle, which may be a completely different material – a plastic overmould, a silicone grip, a stainless steel ferrule – and the junction between them is both a thermal break and a seal.
A food probe’s product-contact surface is a documented release characteristic
Plating, powder coating, anodising or e-coat, with the agreed finish travelling with the part number. On a food probe the finish has four requirements.
- Product-contact surface: passivated stainless steel with a stated finish, or a food-grade material, and documented.
- The handle’s grip surface: a texture or a coating that stays grippy when wet and survives dishwashing. A polished stainless steel handle is the wrong answer here and it is a common one.
- The wetted shaft: smooth enough to clean, resistant to the abrasion of a scourer, and passivated where it is stainless steel.
- And no coating on the product-contact side that can be scratched through – on this application a hard chrome shaft would be a poor choice, because a scratch in a chrome layer in an acidic food is a corrosion site.
Two of the four flagged dimensions on this shell are functional surprises
+/-0.02 mm on machined seats and sealing faces flat to drawing, with critical dimensions carrying CMM data. On this part the flagged dimensions are four, and two of the four are functional in a way that surprises people.
- Sealing faces: flatness and perpendicularity, measured as two values – and on a food probe the seal has to hold against a pressure difference and survive a dishwasher, so it is not a cosmetic face.
- The lead or cable exit’s geometry, because its compression is set by the housing and it is the joint that fails.
- The wetted length, as a functional dimension with a tolerance, because it is the immersion depth.
- And the drain path, which is a hole or a relief and which is a design feature rather than a tolerance – because a probe that cannot drain will hold water against its own electronics for ever.
Cleanability and response are what decide a food probe
First articles and batch samples verified on the CMM. On a food probe two inspection items are not standard, and both are the ones that decide whether the product works.
- A cleanability verification on the product-contact surfaces – a specified method, agreed with the customer, because cleanability is not a measurement.
- A functional immersion test, where the probe is held at a stated immersion depth and the reading compared against a reference. This is the only test that verifies the accuracy claim with its condition attached.
- A leak or dielectric test on the handle joint, depending on whether the handle is sealed against water.
- The dimensional set as normal, and on this part the wetted length’s tolerance matters more than the outline’s.
Dishwasher, and does it touch acidic food?
Does this probe go in a dishwasher, and does it contact acidic food? Two questions that decide the material, the seal, the handle’s construction and the finish – and they are asked in almost every case as an afterthought or not at all. A probe used in a barbecue or in a smoker is in a thermal environment that has nothing to do with the temperature being measured, and a probe used with tomato or citrus or vinegar meets a more aggressive chemistry than most industrial applications ever do. And there is a third question worth asking that is specific to handheld probes and that determines the accuracy claim: how deep will a user actually immerse it? Because on a handheld probe the immersion depth is an operator’s behaviour rather than a drawing dimension, and the accuracy figure moves with it. So a probe specified as accurate to a degree and immersed to half its rated depth is a probe with an unstated accuracy of several degrees – and the fix is not a better sensor, it is a stated immersion depth on the drawing that the instructions repeat and the packaging shows.
Sensor Housings is the range this part sits under; the overview page pulls together the tooling logic, finishing options and tolerance notes that apply across the family.
Specifications
| Item | Stainless Steel Probe Shell with Domed Top Boss |
|---|---|
| Brand | AUNOV |
| Designing | Driven by your drawing or a physical sample – a manufacturability review comes back with the quotation; the approved drawing is kept as the controlled master. |
| Tooling | Die design and toolmaking stay in house, so no tooling step is outsourced, and maintenance is tracked against the part number. |
| Samples | Samples are issued for approval before the run, so the approved first article becomes the gauge reference, and later batches are gauged back to the signed sample. |
| Materials | Carbon steel (SPCC / DC01), 304 / 316 stainless steel, aluminium and brass are held on site; grade and temper are confirmed in writing before tooling. |
| Surface finish | Zinc, nickel or chrome plating, anodising, passivation or e-coat; the agreed finish travels with the part number. |
| Processing | After deep drawing, critical faces are CNC finished; the whole flow is verified on first articles before the run is released. |
| Equipment | Hydraulic drawing presses and CNC lathes for sealing faces; secondary ops run on CNC turning centres, inspection on the CMM. |
| Tolerance | +/-0.02 mm on machined seats, sealing faces flat to drawing; critical dimensions carry CMM data with the shipment. |
| Delivery terms | FOB, CIF or DDP per Incoterms 2020, T/T or L/C, with D/P accepted on repeat business; price breaks tie to annual volume. |
Related Products
Frequently Asked Questions
What does a food probe survive that an instrument probe does not?
It is the one temperature sensor here where the product touches something that will be eaten, so the part becomes closer to a piece of kitchen equipment. It has to be cleanable to a standard, usually survive being dropped into a dishwasher, and be gripped by a wet hand. Deep drawing followed by CNC finishing on critical faces runs at +/-0.02 mm on machined seats and sealing faces flat to drawing, with critical dimensions carrying CMM data.
Why is cleanability not the same as a surface finish?
The cleanability requirement is not a surface finish, it is about there being no crevice or ledge where product can lodge and no texture that traps residue. A product-contact surface has requirements that a general plating or coating callout does not address. Food compatibility comes before corrosion on a food probe, and the product-contact surface is a documented release characteristic.
Why is the handle where a food probe differs most?
The handle is gripped by a wet hand and often dropped, so its geometry and finish are driven by ergonomics and hygiene rather than by measurement. The element and the seal are where the food requirement really bites, because ingress at the lead exit is a contamination path. Accuracy on a food probe is different again, with cleanability and response deciding it.
Dishwasher, and does it touch acidic food?
Those two decide the material, the finish and the seal, and two of the four flagged dimensions on this shell are functional surprises for that reason. Plating, powder coating, anodising or e-coat is selected to suit the drawing, with the agreed finish travelling with the part number. Deep drawing presses and CNC lathes make the sealing faces, with secondary operations and CMM inspection.
Request a Quote for This Part
Send a drawing or sketch — get material advice, tooling cost and a per-piece price within 24 hours (working days).




