This Stainless Steel 6x50mm 6x30mm Sleeve Temperature Sensor PT100 is an Aunov Tech production part in stainless steel, quoted and built to customer print. In service, the sensor housing protects the electronics from vibration, fluid and electromagnetic noise. Die work, machining and CMM inspection are all in-house, so repeat orders stay aligned with the approved sample without re-quoting the job elsewhere.
Product overview
For this stainless steel sensor, the drawing centres on, the draw ratio, corner radii and the faces that must stay flat, each measured at first article and gauged on production batches.
Toolroom, presses and machining centres used on this stainless steel sensor operate on the same site, so revisions do not wait on outside suppliers, with process data archived for repeat orders.
Production route
Every stainless steel sensor follows the same routed path: Coil is blanked and drawn through progressive and single-stage dies; secondary machining holds the seats, threads and faces that forming cannot produce.
Each stepped sleeve shipment is verified against the master sample before it leaves the shop. The signed stepped sleeve sample remains the reference and is kept with the job file.
Materials and surface finish
Working stock covers SPCC / DC01 carbon steel, 304 / 316 stainless, aluminium, brass, copper and bronze with 304 / 316 stainless steel specified on the drawing for this stainless steel sensor.
The finish is chosen for a clean working surface: plating, anodising, powder coating, electrophoresis and passivation. Once approved, the finish for this stainless steel sensor is fixed and does not get re-decided.
The approved sample governs later runs, with mill certificates filed per heat.
Quality control
Quality management is certified to ISO 9001: material traceability starts with mill certificates, a full CMM report approves the first article, and every production run is inspected against the first-article report. Threads are gauged and seal faces inspected on each stepped sleeve batch. If the assembly calls for torque, leak or pressure proof, the test is built into the quality plan, with certificates included in the shipment file.
Applications
This stainless steel sensor is used in sensor and thermostat assemblies in both OEM and aftermarket supply.
One part number for this stainless steel sensor frequently serves several assemblies, so the specification is set by the toughest of them, and the die does not have to change.
Customization and options
Frequently varied options
The parts of the print for this stainless steel sensor that get adjusted: material and coating for the duty, wall bands, flange forms, threads and bosses, closed ends and finishes matched to the working environment, and whether the programme starts as a sample or a full release.
Each quote for this stainless steel sensor states which variations are already tooled, so new tooling is only quoted where it is genuinely required. The stepped sleeve stays as approved until a written revision says otherwise.
Specifications
| Item | Stainless Steel 6x50mm 6x30mm Sleeve Temperature Sensor PT100 |
|---|---|
| Brand | AUNOV |
| Designing | Driven by your drawing or a physical sample – samples are reverse-measured into a controlled drawing; the approved drawing is kept as the controlled master. |
| Tooling | Dies, fixtures and gauges are made in our own toolroom, so die cost stays transparent, and ownership is confirmed on the quotation. |
| Samples | Pre-production samples come with a full inspection report, so the sample is retained as the master, and later batches are gauged back to the signed sample. |
| Materials | Standard stock: carbon steel (SPCC / DC01), 304 / 316 stainless, aluminium, brass; special grades are sourced to the drawing when volumes justify. |
| Surface finish | Finish selected from the drawing: plating, coating, anodising or passivation; alternatives quoted with the quotation, samples approved in writing. |
| Processing | Deep drawing on hydraulic presses, CNC-finished where tolerances tighten; in-process checks sit between stages, not only at the end. |
| Equipment | Deep drawing presses plus CNC turning centres for machined faces, with CNC turning centres for secondary operations and CMM inspection. |
| Tolerance | +/-0.01 mm on thread pitch diameters, +/-0.05 mm on drawn body; finer bands confirmed from capability data before quoting. |
| Delivery terms | Freight is quoted to your door in FOB, CIF or DDP terms, payment by T/T or L/C. |
Packaging and delivery
This stainless steel sensor is packed to protect the finish: interleaving, bagging or tray packing is matched to the surface, in sealed export cartons, palletised and marked as you direct.
